Showing results: 1561 - 1575 of 1792 items found.
-
ADC-2575 -
TestVonics, Inc.
TestVonics ADC-2575 Air Data Calibrator is a high accuracy pitot static calibrator. The calibrator is capable of controlling and measuring Altitude and Airspeed pressures with the highest degree of accuracy. The control and measurement range of the test system can meets or exceed requirements for both commercial and military applications. The ADC-2575 is a derivative of the ADC-2550 Series. It features a touchscreen interface, a mid range 23PSIA sensor. It is ideally suited for Automated Test Equipment (ATE) applications.
-
ULD-420 -
Amprobe Test Tools
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-420 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure. When working in unpressurized systems or the pressure is not sufficient enough to detect or verify a leak with the Receiver alone use the Transmitter.
-
Extech EN100 -
Extech Instruments Corporation
The EN100 is a Compact Hygro-Thermo-Anemometer with Light Sensor. 11-in-1 Environmental Meter for indoor and outdoor conditions. Built in light sensor measures light level. Auto-rotating display depending on selected function. Also measures Air Velocity, Air Flow, Temperature, Humidity, Wet Bulb, Dew Point, Heat Index, Wind Chill, Barometric Pressure and Altitude. Complete with built-in multiparameter sensors, wrist strap, and CR2032 battery.
-
OBS-ONE SPN10 Unit -
HORIBA, Ltd.
The OBS-ONE SPN10 unit is an on-board emissions measurement system for analyzing the SPN10 (solid particle number emissions >10 nm) under real-world driving conditions. It meets the latest trends in particle number regulations in the future.The SPN10 unit combines with the GAS unit and the NH3/N2O unit to measure the specified exhaust gas components, along with the exhaust gas flow rate, the GPS position, and the atmospheric conditions (temperature, humidity, pressure).
-
SG3005 -
Shanghai Jiuzhi Electric Co., Ltd.
The instrument can measure DC positive and negative value of DC voltage, ripple voltage, ripple factor. It can measure AC sine wave (power frequency) and the AC of non-sinusoidal wave voltage peak (positive peak value, negative peak value, peak-peak value), peak value/ √ 2 (true RMS), RMS value of waveform deviation factor and higher harmonics. And can display and save the voltage waveform, pressure raising curve.
-
WIKA Alexander Wiegand SE & Co. KG
For high-precision online monitoring of the gas density, temperature, pressure and humidity of SF6 gas in internal and external systems of SF6 gas-insulated equipment, WIKA gas density sensors are exceptionally suited. The instruments are notable for their high-accuracy sensor technology which guarantees very good long-term stability and EMC characteristics. Optionally, there are hybrid solutions available which combine gas density transmitters with conventional gas density monitors with switch contacts.
-
Nautilus WM10-250 -
Teledyne Marine ODI
Trends in subsea oil & gas production are moving towards deeper water and longer step out distances. These trends drive demand for higher power equipment and higher power delivery and distribution capabilities subsea with high pressures and temperatures. Teledyne ODI'™s Nautilus WM10-250 is designed with the benefit of advanced material science testing and certification, and with insulation and redundant sealing systems for reliable performance in long-term harsh environments.
-
Model T703U -
Teledyne Advanced Pollution Instrumentation
The Model T703U is a microprocessor controlled ozone calibrator for precision gas analyzers. Expanded ozone audit levels have created a need for precise ozone calibration well below the capabilities of standard calibrators. The Model T703U is designed to meet the requirements of ultra-low ozone production.In addition to a high range with similar performance to the Model T703, the Model T703U has the capability to generate ozone in a low range, or "fractional" mode, for producing ozone levels down to 3 ppb, with exceptional accuracy. Flow rate and lamp intensity are adjusted to deliver a specified ozone concentration by volume. The temperature and pressure compensated photometer, identical to that of the Model T400 ozone analyzer, provides feedback control of the UV lamp intensity, assuring stable ozone output. A nearly unlimited number of calibration sequences may be programmed into the non-volatile memory of the T703U, covering time periods up to a year.
-
ADSE 650 -
ATEQ Aviation
The ADSE 650 caters fully for all aircraft types and the different electrical power supplies.It can be used for testing high performance civil and military aircraft, fix and rotary wings. This Pitot Static Tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems.The large touch screen display, with on-screen help ,enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator.
-
Si-AQ VOC Monitor -
Sauermann Group
The SI-AQ VOC Monitor is the ideal instrument for you should your specific application require testing for Volatile Organic Compounds (VOCs) or potentially harmful gasses such as Carbon Monoxide (CO). In addition, the (Si-VOC) Si-AQ VOC Monitor can an also be outfitted with up to three (3) Gases sensors in total among VOC, CO2, CO, Formaldehyde, NO2, NO, O2, SO2 & H2S in addition to measuring Relative Humidity, Ambient Temperature and Barometric Pressure.
-
ADC-2555 -
TestVonics, Inc.
TestVonics ADC-2555 Air Data Calibrator is a high accuracy pitot static calibrator. The ADC-2555 is capable of controlling and measuring Altitude and Airspeed pressures with the highest degree of accuracy. The control and measurement range of the test system can meets or exceed requirements for both commercial and military applications. The ADC-2555 is a derivative of the ADC-2500 Series. It features a touchscreen interface, a mid range 23PSIA sensor and features TestVonics automated calibration software for the TTu-205J Pressure-Temperature Test Set.
-
DPM -
Bee Instruments
Digital panel meters are digital displays intended to be mounted in a panel, such as a control panel. They typically read some type of input, be it a voltage, current, or resistance, and display its value digitally. Often this input is a measurement from a sensor which is converted and displayed as a temperature, pressure, or other system variable. These meters may also act as simple controllers which trip a switch or perform a simple function when the reading reaches a preset measurement.
-
SY081 -
Synectic Electronics
The SY081 Strain Gauge Indicator is a hi-resolution 24bit load indicator. The meter can measure scaled loads on a variety of tranducers. It can display weight, pressure and also torque and offers 10 channels, and 7 point linearisation. The meter is easy to calibrate by applying a known load, or you can enter the mV/V of the load cell from a calibration certificate. The SY081 has a shunt calibration option and a fine adjustment facility to correct for drift over time in transducers.
-
AQ377 -
6TL Engineering
- Compact, transportable and modular test platform.- Ready for ICT, FCT, Boundary Scan, HiPot, Vision or any combination of the previous technologies.- Mass interconnect 9025 Receiver from Virginia Panel.- 100% Compatibility with Inline Test Fixtures (P/N: AT799, AN133 and EB773).- Free available rack space: 47U height- Multi-stage pressure at 3 levels.- FastATE Technology & YAV Modules compatible.- Phi6 Dispatcher Interface.- CE Compliant.
-
DS-0323 -
Ono Sokki
This software analyzes the 1/1 and 1/3 octave bands for 2 - 32 channels (2 - 64 channels when two units are connected ) in real-time from 0.5 to 20 kHz. The filter is compatible with the IEC, JIS, and ANSI standards. The equivalent continuous A-weighted sound pressure level (Laeq) and the single-shot sound exposure level (Lae) are calculated simultaneously by setting measurement time. Variations in level (time series) for each band can be saved for up to 2,000 points.
