Showing results: 6331 - 6345 of 11103 items found.
-
148 -
Elcometer Limited
The Elcometer 148 sensor has automatic temperature compensation, ensuring like-for-like measurements can be taken for meaningful comparison of the results.Simultaneously displays pH and temperatureMeasurement hold / freeze functionRecord maximum and minimum readings over a series of tests°C / °F user switchableWaterproof to IP57 and floats on waterAuto power off
-
PS-625 RVSM -
Preston Products
The PS-625 Pitot-Static tester is designed specifically for those who need an economical RVSM tester. It is a low-maintenance, digital tester that is truly portable. An internal re-chargeable battery enables the test set to be used completely independent of any external power source for 3 hours. $8,995 PURCHASE DIRECT FROM FACTORY
-
11612B -
Keysight Technologies
The Keysight 11612B broadband high power bias network can be used in a wide variety of biasing applications for test and measurement requirements in laboratory and production environments. Bias networks provide the means of supplying dc bias to the center conductor of the coax connector for your device while blocking the dc to the RF port.
-
11590B -
Keysight Technologies
The Keysight 11590B broadband high power bias networks can be used in a wide variety of biasing applications for test and measurement requirements in laboratory and production environments. Bias networks provide the means of supplying DC bias to the center conductor of the coax connector for your device while blocking the DC to the RF port.
-
BKP3-CEN07-15.2.3-4 -
Kontron
his 7 slot Hartmann Open VPX BKP3-CEN07-15.2.3-4 profile system chassis provides an intelligent, practical packaging solution for high-performance processors. The 50HP wide, rack-mountable enclosure for vertical mounting of boards is outfitted with a 600W plug-in power supply and a 1U removable, bottom mount fan tray.
-
11612A -
Keysight Technologies
The Keysight 11612A broadband high power bias network can be used in a wide variety of biasing applications for test and measurement requirements in laboratory and production environments. Bias networks provide the means of supplying DC bias to the center conductor of the coax connector for your device while blocking the DC to the RF port.
-
Teledyne e2v
Spark gaps are high-energy, voltage-controlled switching devices that are unique in their ability to repeatedly switch currents of thousands of amperes.They are commonly used as protection where high-energy transient electrical surges are anticipated, such as voltage protection, lightning protection and crowbar circuits. They are also used to power the lithotripters used to treat kidney stones.
-
VOA 1000 / 1100 / 1300 Series -
Quantifi Photonics Inc.
The VOA Series is a MEMS-based variable optical attenuator with fast attenuation speed, low insertion loss and in-built power meter. Its advanced power stabilization function lets you set and maintain the output power stability even when the input power fluctuates.It is available in singlemode, multimode and polarization maintaining fiber types and various wavelengths to suit a wide range of applications.With 1 or 2 channels in a single PXIe slot, it provides high channel density solution for easy integration in the versatile PXI platform.
-
LXinstruments GmbH
The load system is intended for testing satellite power supply systems; due to the integration with a solar array simulator and a battery simulator, it can perform validation and commissioning of satellite power supplies. The system is equipped with regenerative electronic loads and customer-specific high-power switching matrices for routing the DUT channels to the relevant loads. The individual voltages and currents for each channel can be read back via a Keysight Technologies switch mainframe.The system is equipped with high electrical power; its loads are capable of feeding the energy back into the power grid.
-
34938A -
Keysight Technologies
The Keysight 34938A is a high power general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 20 independent single-pole, single-throw (SPST) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Its 30VDC/250VAC, 5A contacts can handle up to 150W on a single channel, enough for many power line switching applications. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
SHERLOG -
KoCoS Messtechnik AG
Fault recorder systems with a power quality analyser for comprehensively monitoring and assessing low, medium and high voltage networks in power plants and transformer substations. The measuring devices of the SHERLOG range make very high-resolution recordings of all the disturbances which occur in power supply systems. The behaviour of protection and switchgear devices during these system disturbances is recorded at the same time.
-
DCZCT-20MH -
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement for solar power system*Least affection from the magnetization of core and temperature fluctuation*DC leakage current measurements*Convenient +5V single polarity power supply
-
RL -
Junxy Energy
Resistive & reactive load banks are able mimic motor loads and electromagnetic devices within a power system as well as purely resistive loads by offering the ability to set a specific power factor (pf). Many backup generators and turbines are rated at 0.7, 0.8 or 0.85 power factor and need to be commissioned at nameplate capacity using a combination of resistive and reactive load to fully qualify their operating capability. Using a resistive & reactive load bank enables comprehensive testing from a single unit. JUNXY has an extensive range of resistive & reactive load banks to simulate these types of loads on a power source and the transformers, relays, and switches which will distribute the power throughout your facility.
-
MT-1A -
Mitech Co., LTD.
MT-1A digital portable magnetic flaw detector, adopts large capacity lithium battery power supply. DC is exchanged into AC by the inverter and the phase shifted signal processor to provide power for the detector, it solves the shortcomings of traditional magnetic particle detector relying on the 220V power supply. It has low power consumption and can continuous work for more than 4 hours. The battery can be charged while working or off. It can real-time monitoring, process image, save data, print the test report, track inspection results, meet the requirements of standard operation and management. Especially suitable for the field without power supply field testing and high-altitude operations, it realizes the innovation of magnetic powder digital inspection.
-
RVG-SD1 -
Curtiss-Wright Defense Solutions
The RVG-SD1 is a rugged, size, weight, power and cost (SWaP-C) optimized 3G-SDI video switch designed for use in the harsh environmental conditions occurring in aerospace and defense applications. Part of the Rugged Video Gateway (RVG) family, its small size allows it to be incorporated into space-constrained manned and unmanned vehicles of all types.