Showing results: 31 - 45 of 297 items found.
-
CozIR®-LP -
Gas Sensing Solutions Ltd.
The CozIR®-LP is part of a new generation of ambient CO₂ sensors optimised for low-power applications. The CozIR®-LP uses NDIR solid-state LED optical technology to create a sensor with a small footprint and ultra-low-power consumption. This makes it ideal for a new generation of portable and battery powered ambient measurement applications that require highly accurate CO₂ measurement capability.
-
Spanawave Corporation
Measure CW power from 10 MHz to 50 GHz at more than 17,500 readings per second over GPIB. Measure up to 90 dB with a single sensor, and select from a variety of high power sensors up to 50 W.
-
DARE Electronics
DC voltage sensors monitor input voltages ranging from 3 to 500 volts DC with a trip point accuracy of up to 1% in airborne, military and ground power applications. Using internal electronic circuits to detect, monitor and/or sense DC voltage, DARE DC voltage sensors, monitors, and voltage sensing relays can open or close a circuit when a certain pre-set over or under voltage condition exists or the DC voltage falls outside the specified voltage band window.
-
KD-5100 -
Kaman Fuzing & Precision Products
* Two precisely matched sensors per channel give resolution to a nanometer.* Superior thermal and long-term stability of 5x10-6 inches/month or better.* Small package size: 2 x 2.12 x 0.75 inches thick.* Cryogenic sensors available.* High sensitivity: up to 10 V/mil (394 mV/mm).* Low power consumption: less than 2W @ ±15 Vdc typical.
-
7250 -
AMETEK Drexelbrook
The 7250 Series digital stiks take field proven magnetostrictive sensing technology and packages it for greater reliability and easier installation. This liquid level sensor is ideal for liquid level monitoring, interface level and leak detection in a variety of liquid media in above ground and underground storage tanks. It was designed to meet EPA Leak Detection and API Inventory Monitoring requirements and has been approved for use in hazardous environments.The 7250 Series is series has an inherently lower cost design which results in savings. It provides the same performance and reliability as sensors that consume more power.
-
MT322-107 -
ALTINEX, Inc.
The MT322-107 distributes AC power from a single AC source to multiple AC outlets. These outlets can be connected to any type of audio/video equipment. The total current supplied to all outlets must be less than 10 A. Built-in sensors alert the user by flashing the LEDs when the load exceeds 8.5 A and a warning message is sent to the RS-232 bus when the current draw is near maximum.
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitter for load cells and the evaluation of strain gages in 6 mm housing with calibrated range selection.Detection signals from sensors for physical variables such as displacement, angle, pressure or force. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
WIKA Alexander Wiegand SE & Co. KG
For on-site display of pressure values, pressure sensors can be combined with attachable indicators, for the central pressure indication there are digital indicators for panel mounting available. Our electrical accessories also include power supply and control units, intrinsically safe repeater power supplies and also pre-assembled connectors with cables.
-
N Series -
IDS Imaging Development Systems GmbH
The compact and robust aluminum housing of the camera with lockable GPIO connector for trigger and flash and GigE connector, has two monochrome CMOS sensors and a projector. The projector is available either with blue lights in the visible area or with infrared lights. Via Power over Ethernet a data transfer and power supply are possible with long cable lengths.
-
Thorlabs, Inc.
These interfaces provide communication between an attached sensor and a PC or other external control unit. They are designed to be controlled via an external device or operated autonomously using the analog output; there are no controls or display screens.
-
DARE Electronics
DARE?s frequency sensors and monitors are available in both AC powered and DC powered models in a wide variety of standard or custom enclosures. Used in aircraft, ground support equipment (GSE), ground power applications, and other military and industrial applications, DARE frequency sensors, monitors, and frequency sensing relays will protect equipment that is sensitive to fluctuations in power line frequency from damage due to over and / or under frequency conditions.
-
X005 Series -
Positek Limited
The X005 Galvanic Isolation Amplifier provides a regulated and resistively limited +5V dc power supply required by the sensors, it can be connected in three or five wire modes. Used in five wire mode positive and negative sense inputs enable the X005 to dynamically adjust the sensor supply thus ensuring the correct voltage across the sensor. Connected in this way the X005 can compensate for 15 conductor resistance. The sense terminals are linked internally so the end user can use the X005 in three wire or five wire mode without the need to fit or remove external links.
-
Ultima® X -
MSA
The Ultima X Series Gas Monitors with X3 Technology bring the power of multi-sensing, signal boost and ModBus output to the Ultima X line of MSA gas monitors. The units are crafted from either stainless steel or NEMA 4X-rated plastic, and our patented SafeSwap sensor disconnect-underpower feature allows all sensors to be replaced in hazardous areas without area declassification.
-
BW-AED-500 -
B&W Engineering Corp.
The input can range from 40Hz to 160KHz from sensors with similar ranges. The output can be delivered to a speaker, oscilloscope and an LED for threshold detections ranging from 0-Infinite. The power supply features regulated +5VDC, -5VDC, +12VDC, +15VDC, -15VDC and +/- unregulated 20VDC. Voltage input of 110VAC @ 60Hz or 220VAC @ 50Hz.
-
Framos Technologies d.o.o.
FRAMOS is the first company in the market to integrate Analog Devices’s new GMSL3 technology into an embedded vision environment. GMSL3 can transmit high frame rates (4K, 90 fps) as far as 14 meters with unprecedented efficiency. This interface is well suited for applications where the MIPI CSI-2 (D-PHY) length restrictions are not sufficient, while at the same time, a highly durable cable with low power consumption and low cost are essential. Camera developers can use the flexible FRAMOS Sensor Module Ecosystem to validate a variety of image sensors in the lab and in the field while taking advantage of the interface’s features.