Filter Results By:

Products

Applications

Manufacturers

Phase

the difference between two features of a waveform, measured in any of multiple manners (distance, time, angle, wavelength, etc.)

See Also: Phasing, Phase Standards, Phase Meters, Phase Angle, 3 Phase, Time


Showing results: 1231 - 1245 of 1608 items found.

  • Tensile Strength Tester

    Atico Export

    Capacity of Tester with accuracy of 100g : 250 Kgf. and 500 Kgf.Capacity of Tester with accuracy of 10g : 20 Kgf, 50 Kgf and 100 KgfS Type Load Cell fixed with Top GripTraverse Speed: 300 & 100mm /min.Grip Separation: 1000 mmGrip Separation: 25 mmTop Grip is fixed and Bottom Grip is Movable Type.Elongation measurement by Steel Scale and Digital Counter Meter Both.Digital Display of Load and Elongation.Peak value of last test can be read.User friendly key panel with switch of zero setting and peak value of last testMotor: 1/2 HP single phase 220V 50 Hz. ( for Capacity up to 100 Kgf )Motor: 1 HP single phase 220 V 50 Hz ( for Capacity up to 500 Kgf)Power: 220 V AC 50 Hz.Safety device by limit switch to protect from over traverse.

  • Automotive Protocol Decode/Trigger Software (CAN, CAN FD, CAN XL, LIN FlexRay, SENT) for Infiniium Oscilloscopes

    D9010AUTP - Keysight Technologies

    - Set up your scope to show CAN, CAN FD, CAN XL, LIN, FlexRay, and SENT protocol decode in less than 30 seconds- Support CAN XL protocol trigger and decode of the SIC mode (or slow mode) signal in the arbitration phase as well as the FAST mode signal in the data phase- Get access to a rich set of integrated software-based protocol-level triggers- Save time and eliminate errors by viewing packets at the protocol level- Use time-correlated views to quickly troubleshoot serial protocol problems back to their timing or signal integrity root causeThis application (for Infiniium Oscilloscopes) includes a suite of configurable protocol-level trigger conditions specific to CAN, CAN FD, CAN XL, LIN, FlexRay, and SENT. When serial triggering is selected, the application enables software-based triggering. Application supports CAN-dbc symbolic debug.

  • 3207a GPS/GNS Frequency and Time Reference

    GlobalTyme2 - Precise Time and Frequency, Inc.

    The ptf 3207A GlobalTyme2 GNS Receiver introduces a new level of advanced capability from a second generation, based on the highly successful ptf 3203A and ptf 3204A GlobalTyme receivers.The unit is both a frequency standard and a time standard and has been used as a precision frequency reference with low phase noise, in satellite communications applications around the world.

  • 3207a GPS/GNS Frequency and Time Reference

    Precise Time and Frequency, Inc.

    The ptf 3207A GlobalTyme2 GNS Receiver introduces a new level of advanced capability from a second generation, based on the highly successful ptf 3203A and ptf 3204A GlobalTyme receivers.The unit is both a frequency standard and a time standard and has been used as a precision frequency reference with low phase noise, in satellite communications applications around the world.

  • Data Stream Digital Transducers

    CR MAGNETICS, INC.

    The Data Stream Series provides a digital stream of data that can contain complete electrical properties information including current, voltage, power, phase angle and frequency. Additionally, an energy totalizer can be configured to give total energy calculations. All data is transmitted via an RS485 bus, and a single bus can communicate with multiple devices. MODBUS capable programming is also available.

  • Voltage Indicators

    Greenlee Tools

    *Measures voltage from 100V to 138kV line‑to‑line.*Can be used individually as voltage indicators or together for phasing operations up to 100 ft (30 m) apart.*Two LED displays are automatically synchronized during phasing operations.*Clear in-phase and out-of-phase indication.*Versatile for overhead and underground applications.*Capacitive Test Point and Peak Hold modes

  • Testing & Quality

    Ecoprogetti srl

    The solar simulator, electroluminescence and hi-Pot testers are the main machines used to test photovoltaic modules. These machines can be positioned at the end of the production line and along the production chain to keep the quality and efficiency of the photovoltaic modules under control after the most sensitive production phases. Each machine uses the best technologies in order to guarantee the best and most accurate measurements.

  • Saluki CSA Series Signal Analyzer (Modular)

    Saluki Technology Inc.

    Saluki CSA series signal analyzer reaches the frequency from 100 kHz to up to 26.5 GHz with a maximum of 40 MHz analysis bandwidth. It can test signal power, frequency, phase, P-1, TOI, OBW, channel power, spurious, ACPR, CCDF, SEM, EVM, and other indicators. It can be used independently or combined with the chassis to form a test system.

  • Mezzanine System

    5093 - Abaco Systems Inc

    ECM P/N 5093 provides 2 independent full bridge circuits. The two full bridge circuits can be used together to drive one small two phase stepper motor. Each full bridge circuit can drive one small dc motor or other bipolar load. Note all inductive loads should employ transient protection.

  • Microwave / RF Synthesizers, Test & Measurement

    Berkeley Nucleonics Corporation

    The 825-M is an agile ultra-low phase noise RF signal source from 8 kHz to 20 GHz RF Synthesizer. It is available in single-channel or multichannel configurations. A single channel 825-M is packaged in a compact enclosure, or can be ordered with a touch-screen display, or a 1U 19" rackmountable version. The multi-channel version (2, 3, or 4 channels) is packaged in a 19” 1U rackmount enclosure.

  • Frequency Response Analyzer

    1253A - Ametek Scientific Instruments

    The 1253A Frequency Response Analyzer (FRA) is an instrument that is capable of meeting today's measurement requirements for dynamic system analysis. Using the Single Sine Correlation technique (SSC), it provides precise data relating to the gain and phase between any points in a dynamic system. This instrument enables engineers to perform searching analysis to assess performance of both simple or complex systems.

  • Signal & Spectrum Analyzer

    FSVA3000 - Rohde & Schwarz GmbH & Co. KG

    Analysis bandwidth of up to 1 GHz, outstanding phase noise of –120 dBc/Hz and a high dynamic range give the R&S®FSVA3000 signal and spectrum analyzer everything needed for demanding 5G NR measurement applications. High measurement speeds and easy usability make it ideal for demanding signal analysis, both in the lab and on the production line.

  • TEST BOX

    6280 TB - Standard Electric Works Co., Ltd

    ● Wide range of operating voltage from AC 210V/50Hz to 250V/50Hz.● For checking AC voltage.● For checking a RCD tester's test current & time in mA(ms).● For checking a loop tester.● For wiring check (Phase, Neutral, Earth).● For checking continuity.● For checking insulation (The maximum is 1.2kV).● For checking UK16th edition.● Safety standard: EN 61010-1 / EN 61326-1

  • Power Analyzers

    PCE Instruments

    At PCE Instruments you will find a power quality analyzer to measure the power in W, kWh or to analyze and measure harmonics. This power analyzer is a multi-function power analyzer device that measure precisely direct current, alternating current, AC-voltage, DC-voltage the intensity of DC or AC, phase rotation and idle, apparent and effective power. The reading of AC power is considered the real value and has a maximum range of 6000 Watts. While a reading is being taken, the polarity changes automatically, if negative values are taken then a minus sign will appear on the device display.Nowadays, power quality analyzers have many features such as, insulated current input, measurement of harmonics, AC and DC current measurement, AC and DC voltage measurement, frequency measurement, phase rotation measurement and idle, apparent and effective power measurement. All this data can also be logged and analyzed with the delivered PC-Software. Power analyzers of the type PCE PA 6000 can determine the energy in single-phase systems.Power quality analyzers of type PCE-GPA 62 allow the energy measurement in symmetrically loaded three-phase systems. Power analyzers of type PCE-PA 8000, PCE-360 and PCE-830 support professional power and energy measurements in single and three-phase systems.Apart from being used as energy-measuring devices, power analyzers like the PCE-830 can also be used for network analysis and the determination of harmonics and phase rotation. On our website you will find other power analyzers used in the field of electronics.

  • Multi SDI Monitors

    LV 5333 - Leader Electronics Corp.

    LV 5333 Waveform Monitor is a powerful, versatile video production tool that is compact and portable. LV 5333 has a high quality TFT LCD screen which produces high quality picture images. Waveform, Vector, Audio, Status and 5 Bar gamut displays are all included in this precision instrument. These can be displayed full screen or in various multi-display combinations. LV 5333 can also display the levels of an embedded audio signal. Plus, Cable Length, External Phase Difference, and Field Frequency Deviation measurements are standard along with CINELITE® II. Now with HD HDR monitoring as an option, the LV 5333 can be carried as a portable unit or rackmounted for studio or flypack use.

Get Help