-
product
15-Pin D-Type Connector, Male
40-963-015-SM
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 15-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
product
8 Pin Power D-Type Male Connector, 40A, PCB Mount
40-963-008-RM
This connector is suitable for Pickering Interface's modules that use the 8-Pin Power D-Type connector. It is designed to allow users to make a termination via a PCB.
-
product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to 2x68 Female VHDCI Connectors
510150126
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2x68 Female VHDCI Connectors
-
product
Metal Cored PCB
Teledyne Labtech is at the forefront of complex metal-cored PCB design and manufacture. The PCB use a thin metal core <2 mm, which acts as isolation between the RF/Microwave circuit and the Analogue/Digital circuitry and creates an excellent thermal path.The major advantages are reduced size and no need for complex microwave feed-thru's. The ability to laser cut pockets allows the designer engineer to mount the high power MMIC directly on to the metal core.
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type C, Ø1.50mm, 230gf
K100-C150230-SKAU
K100 Series, Pitch 100mil, Tip Style C, Tip Diameter Ø1.50mm, Spring force 230gf, Steel with Gold Plating.
-
product
Pin Point Range Systems
The PinPoint Alpha system is a flexible, adaptable and modular PCB and IC fault finding system, which allows you to apply different electronic test methods to obtain maximum test coverage and fault detection. Test signals can be applied at the PCB edge connector or through test clips and DTIs to perform fixtureless in-circuit testing.
-
product
Signal, Contact, ITA, QuadraPaddle, Male PCB Pin
610138123
Signal, Contact, ITA, QuadraPaddle, Male PCB Pin.
-
product
MPI PCB Probe Systems
MPI Advanced Semiconductor Test
Every MPI manual probe systems can be configured with a variety of different holders for printed circuit boards (PCB’s) in order to provide in addition to on-wafer, versatile, convenient, and accurate Signal Integrity (SI) measurements with single-ended or differential RF probes. Measuring signals at the end of the channel for eye-patterns, deterministic jitter, distortion, TDR (Time Domain Reflectometry) impedance, cross-talk, coupling, and losses, or even S-parameters is easily accomplished.
-
product
PCB Design and Assembly
Innovative Circuits Engineering, inc
Turnkey services for Printed Circuit Boards: Design, Fabrication, Assembly and Testing
-
product
PXI Pull-Thru Adapter, PCB, QuadraPaddle, 68-Pin Male VHDCI
510140125-2
PXI Pull-Thru Adapter, PCB, QuadraPaddle, 68-Pin Male VHDCI
-
product
Printing / Squeegee Force
CmPrint
Measurement of the Force-Time Curve while Printing. The first step into the manufacturing of electronic printed circuit boards (PCBs) is printing. The solder paste is printed on the PCB using a stencil. The equal distribution of the paste pressure is crucial and affects the overall quality of the finished circuit board. An important influencing factor is the accuracy and reproducibility of the squeegee force.
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type K, Ø1.50mm, 230gf
K100-K150230-SKAU
K100 Series, Pitch 100mil, Tip Style K, Tip Diameter Ø1.50mm, Spring force 230gf, Steel with Gold Plating.
-
product
VXI Rev 4.0 Module Shield Kits
*One, two and three slot-wide kits for VXI Modules with 150-pin connectors. Shroudless design fits rev 4.0 chassis. All kits include side shields, a pre-machined blank front panel, ejector handles, all necessary hardware and assembly instructions. *Easy PCB layout using our CAD layout aids. All kits are available with customized front panels and side shields.
-
product
EDA Software
Shorten design cycles to achieve first-pass design success. Our next-generation integrated electronic design automation (EDA) software provides engineers with new tools and enhancements to bring efficiencies into their printed circuit board (PCB), RF and microwave, 5G / 6G, and high-speed digital design flows.
-
product
High Voltage Dry Reed Relays For up to 10kV
Series 67 & 68
Series 67 PCB mounting with switch and coil connections in a Single-in-Line format.Series 68 PCB connections on the underside for coil connections. Flying leads from the top face for high voltage connections.The Series 67 and 68 are constructed using former-less coils. The absence of a coil supporting bobbin allows a device smaller than the industry norm. The unusual package design gives some interesting possibilities for high density packing.The option of flying leads for the high voltage connections makes it possible to keep this away from lower voltage circuitry on the pcb.Form A (energize to make) contacts are available with the option of 5, 12 and 24 volt operating coils.
-
product
PCB Data Logger
DL-3
The PCB Data logger is a proprietary data logger designed by DLM for use in the offshore industry. Comprising of multiple on-board sensors and with extra capacity for external mV or mA inputs, the DL-3.0 can sample on-board and external sensors at customisable sample rates of up to 800Hz.
-
product
24-Pin SOWIC-to-22-Pin 0.400" CRT DIP Adaptor for 75ALS162 and Others
1111903
24Pin SOWIC IC to 22Pin .4 CTR DIP Adapter for 75ALS162 and other IC?s. A cost effective means of upgrading to SOIC without changing your PCB layout.
-
product
µHELIX® Test Probes
Series S200, S300, S400, and S500
Test Probes for fine-pitch applications: CSP, BGA, SiP, SoC, flex-circuits, micro pcb, sub-mm center-to-center spacing, half mm, quarter mm spacing. Excellent for use in sockets, fixtures, and contactors for semiconductor testing and in coaxial installations.
-
product
Signal, Contact, ITA, TriPaddle, Round Post, PCB Mount
610110000
Primary mating contact 610110179. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAAVG Mating Force(lbs) 0.41Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 Cycles
-
product
General Purpose Pressure Sensors For High Frequency
PCB® Series 113B dynamic pressure sensors set the standard for extremely fast, micro-second response with a wide amplitude and frequency range. These characteristics allow them to excel in high-frequency applications, where minimum sensor diameter is required.
-
product
Loudspeaker Cable Testers
EMO E450
The EMO E450 cable tester will test for continuity, cross connection, and open circuit in cables fitted with NL8FC 8-pole and NL4FC 4-pole Speakon connectors, 3-pin XLR connectors, and 2 or 3 pole A-gauge jacks. EP retrofit kits are available to allow cables fitted with EP 4, 5, 6, or 8 pin connectors to be tested. The EP connectors fit in two pre-punched holes on the rear of the tester accessed by removing the blanking panel. The kit's flying leads plug directly into connectors mounted on the tester's PCB.
-
product
Heavy Copper PCB
Your product descrVictory is a professional Advanced Circuit Manufacturer, We provide 3OZ ~ 6OZ Heavy Copper PCB.Heavy Copper PCB are generally used for high power distribution, heat dissipation, planar transformers, and power convertors. We can make up to 6oz Heavy Copper PCB.iption goes here.Monthy Capability: 3500 Sq M/MonthLayer: 4 LayersMaterial: FR4 TG170Dimension: 350.56mm*580mmFinished board thickness: 2.3mmOuter layer Finished copper thickness: 6ozInner layer base copper thickness: 6ozMin Trace Width/Space: 14milMin hole size: 0.2mmMin hole wall copper: ≥25UMSoldermask Color: Gloss BlackSilkscreen Color: WhiteSurface finishing: HALApplication field: Communication Field
-
product
24-Pin SOIC w/Package-to-22-Pin 0.400" DIP
22-304504-18
24Pin SOIC w/ Package to 22 Pin .4 DIP. A cost effective means of upgrading to SOIC without changing your PCB layout.
-
product
Pressure, Force, Torque and Acoustic Measurements
STI Technologies Inc. is uniquely positioned, through its relationship with the PCB Group of companies, to offer a range of pressure, force, torque and acoustic measurement services and a full range of data analysis tools for evaluation and resolution, as well as access to a host of pressure, force, torque and acoustic sensing devices.
-
product
2-Port Optical Tunable Filter
Optoplex's Tunable Optical Filter, also known as Optical Tunable Filter or Tunable Bandpass Filter, is an integrated module, consisting of micro optics and electronics. When receiving a stream of optical signals of a plurality of wavelengths from the Input-Port (IN), the 2-port tunable optical filter directs a selected channel to the Output-Port (OUT). The selected channel can be varied (tuned) within the operating wavelength (frequency) range by a remote command sent through the built-in control PCB and firmware.
-
product
PCB Transmission Line Field Solver
Si9000e
With its fast, accurate, frequency-dependent transmission line modelling, the new Si9000e is designed to model transmission line loss, impedance at given frequencies and extract full transmission line parameters over a wide range of popular PCB transmission lines (over 90 structures).
-
product
50-Pin D-Conn Female Straight PCB, HV
40-963-050-SF-HV
Ideal for user created termination schemes where the termination is to be on the front or remotely connected to the module by cable. Suitable cables for this product are detailed in the data sheet. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
product
Linear Testfixture (Cassette Not Included), UTT 586 x 248 mm
MG-03
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 586 x 248 mm (wxd• Outer dimensions: 750 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for changeable cassette
-
product
15-Pin D-Type Connector, Female
40-963-015-RF
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 15-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
product
PCIe Gen3 4K Compact, High Speed Camera for Testing
CB120CG-CM-X8G3
4K, compact, high speed camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
