Showing results: 856 - 870 of 9914 items found.
-
ROM-2820 -
Advantech Co. Ltd.
Advantech ROM-2820 OSM 1.1 Computer-on-Module is powered by NXP i.MX 93 SoC which includes Cortex-A55 Dual-core in combination with one Cortex-M33 real time processor, Ethos®-U65 Neural Processing Unit (NPU) and 2D graphics engine. It provides USB2.0, Gigabit Ethernet, MIPI-CSI, I2C, SPI, GPIO, CAN-FD and MIPI DSI display for embedded applications
-
Dewesoft d.o.o.
Human and Whole Body Vibration TestingThe human and whole-body vibration module tests and measures the effect of vibration on the human body. The extracted parameters allow the simple assessment of the injuries risk for workers, exposed to constant vibration. Our solution supports the whole-body and hand-arm vibration measurement are supported according to all relevant international standards - ISO 5349, ISO 8041, ISO 2631-1 and ISO 2631-5.
-
HY-TTC 30XSH -
TTTech Computertechnik AG
HY-TTC 30XSH, a member of the HY-TTC 30X family, is certified by TÜV Nord according to the EN 13849 standard and fulfills Performance Level c (PL c) requirements. Just as the other family members this certified unit must be used in combination with a master module. For safe communication the standardized CANopen Safety protocol is applicable since compliance to the European standard EN 50325-5 for CANopen Safety is provided.
-
Unitech Scales And Measurements Pvt. Ltd
The setup is a table top module, it comprises of source and measuring tank. The measuring tank is made of acrylic material with gradation marked in liters. A small FHP pump is fitted to circulate the water. A rotameter with control valve is used to measure the flow rate. Digital timer is provided to note down the duration of flow and the volume of water is measured by the markings on the measuring tank to calculate the actual flow rate
-
Framos Technologies d.o.o.
Embedded Vision applications have specific vision requirements. Image sensors (IMS) are not only part of stand-alone camera systems anymore. Today, IMS are very tightly integrated with processors into heterogenous “Embedded Systems“. The FRAMOS Ecosystem of Sensor Modules and Adapters provides vision engineers and developers with ready-to-use compositions of hardware, software and reference designs to accelerate time-to-market and optimize resources.
-
Bloomy Controls, Inc.
Bloomy’s 8-Channel Thermocouple Simulator Module provides eight channels of galvanically-isolated thermocouple simulation and simulates types E, J, K, M, N, and T thermocouples. High-precision digital-to-analog converters which are isolated from each other and from system power provide sub-microvolt resolution and accuracy. Built-in switching provides open-circuit faults as well as switching to system calibration resources.
-
MNS-300EM -
Silex Technology
MNS-300EM is an embedded module that provides mesh connectivity for low-power portable devices to connect to a 802.11s capable mesh network. It features an 802.11ac radio, and a complete TCP/IP network protocol stack with an optimized QCA9377 wireless radio driver and security supplicant in a self-contained hardware package. It also supports enterprise security which ensures data integrity and privacy for highly sensitive applications.Embedded Wi-Fi Mesh with Enterprise Security
-
TFMC900 -
TEWS Technologies GmbH
The TFMC900 is an FMC (FPGA Mezzanine Card) Mezzanine Module designed to test ANSI/VITA 57.1 FMC Carriers during development or series production. Additionally, it offers the possibility to realise various I/O solutions for connected FMC Carriers. Interconnection of the High Pin Count FMC Connector signals can be verified by JTAG and by functional tests. A loop-back of the 10 multi-gigabit transceiver interfaces allows interconnection checks for the high-speed serial interfaces.
-
EXC-4000VME/xx / EXC-4000VXI/xx -
Excalibur Systems, Inc.
The EXC-4000VME/xx and EXC-4000VXI/xx cards for VME & VXI systems supports up to eight dual redundant MIL-STD-1760 channels using the M4K1553Px(S)-1760 module and is compatible with all common variations of MIL-STD-1760 (A, B). Each channel can operate simultaneously as a Bus Controller and up to 32 Remote Terminals and as a Triggerable Monitor. In addition, Checksum, SRQ bit and Header Words are supported on each channel.
-
SCANIO Family -
Corelis, Inc.
The Corelis family of SCANIO™ modules turn any IEEE standard 1149.1 boundary-scan controller into a powerful digital boundary-scan tester. The SCANIO family of products use boundary-scan gate arrays to add control and visibility to connectors, traces, and logic that can not be tested using traditional boundary-scan techniques.The SCANIO products, when combined with a boundary-scan controller, operate as a traditional “bed-of-nails” tester except access to the stimulus and response I/O’s is achieved via boundary-scan.
-
JT 2139 -
JTAG Technologies Inc.
The JT 2139 is a TAP signal isolation module designed for use in combinational test systems that utilise multiple instrument interfaces. To avoid parasitic capacitance effects and/or unwanted ground loops the JT 2139 can be used to completely galvanically isolate any JTAG Technologies boundary-scan controller from the remainder of the instrumentation system. JT 2139 isolators are a standard component of the JTAG Technologies ‘Symphony’ systems that integrate boundary-scan with In-Circuits Testers etc..
-
Pasternack Enterprises, Inc.
The Pasternack / Vubiq 60 GHz development system provides rapid evaluation of Pasternack’s 60 GHz waveguide modules and customer prototyping for system development. This 60 GHz developer kit is created from a partnership between Pasternack and Vubiq (pronounced “View-bik”), an industry expert in designing 60 GHz RF systems. Our 60 GHz wireless development system makes it easy to design new products and applications in the emerging unlicensed millimeter wave ISM band.
-
BRIC, -
Pickering Interfaces Ltd.
High Density Packaging and Integrated BackplanesWith Pickering's BRIC Large PXI Matrix Modules, the use of high density packaging and integrated backplanes enables a large matrix to be implemented with no user configuration or special matrix expansion kits. These matrices use thru-hole mechanical relays (not surface mount) and can be serviced using standard de-soldering tools simplifying repair and reducing down time. Our BRIC's integrated design ensures high matrix performance with high signal bandwidth and fewer system implementation errors.
-
Diamond SA
MAT active device transmitter modules permit the direct coupling of signals into fibers terminated with E-2000™ connectors. MAR receivers perform the reverse receiving function. Both types are carefully designed to offer a high degree of optical stability over widely-varying environmental and mechanical-stress conditions. Rugged construction ensures stable, repeatable operation over 1000 mate/demate cycles. MAT and MAR incorporate the following features: positive latching mechanism, spring-loaded shutters for eye-safety and compact footprint.
-
Acery Technologies
The 34950A module has 64-bit bi-directional lines and can be configured with 8 8-bit digital I / O channels with handshaking capability. Each 8-bit channel has programmable polarity and a threshold of up to 5V. The memory can be used to generate or capture digital patterns up to 10 MHz. It provides seven configurable handshaking protocols for a wide range of applications. In addition, two counter / totalizer channels can be used to compute events, frequency, period, duty cycle, accumulation, and pulse width.
