Showing results: 8851 - 8865 of 9914 items found.
-
40-728A-001-L -
Pickering Interfaces Ltd.
The 40-728A-001-L (PXI) and 42-728A-001-L (PXIe) are 16x2 50 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
42-728A-001-L -
Pickering Interfaces Ltd.
The 40-728A-001-L (PXI) and 42-728A-001-L (PXIe) are 16x2 50 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
RCNIC-A2PA3 -
Abaco Systems Inc
The RCNIC platform is a high performance, 3U CompactPCI module (PMC on carrier card) for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation. An IRIG-B receiver/generator is included for synchronization to an external IRIG-B time source and for synchronization between multiple RCNIC boards.
-
40-592-121-186X8-2P -
Pickering Interfaces Ltd.
The 40-592 FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC™ format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short-circuits to ground or battery, or short-circuits between input/output lines.
-
40-592A-115 -
Pickering Interfaces Ltd.
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
M9192A -
Keysight Technologies
The Keysight M9192A DSR Pattern Editor Software adds additional advanced capability to the Keysight M9195A/B PXIe digital stimulus/response (PXI DSR) modules by providing a graphical user interface for the development system. M9195A/B error log files can be dragged-and-dropped into waveform editor which speeds up the debugging of tests; this gives immediate visibility of discrepancies between the expected state in the ATE patterns with that of the DUT.
-
782458-01 -
NI
8-Slot, Virtex-5 LX85 FPGA, MXI-Express CompactRIO Chassis - The NI‑9155 is a rugged MXI‑Express chassis for high-performance, high‑channel‑count applications. With the NI‑9155, you can add C Series I/O modules to your PXI system or industrial PC. You can daisy chain up to six NI‑9155 chassis in a single chain and connect up to eight chains to a single controller.
-
782457-01 -
NI
8-Slot, Virtex-5 LX50 FPGA, MXI-Express CompactRIO Chassis - The NI‑9154 is a rugged MXI‑Express chassis for high-performance, high‑channel‑count applications. With the NI‑9154, you can add C Series I/O modules to your PXI system or industrial PC. You can daisy chain up to six NI‑9154 chassis in a single chain and connect up to eight chains to a single controller.
-
786598-01 -
NI
PXIe, 1-Channel, SMF28 Fiber, 1x4 PXI Optical Switch - The CohSol SwitchPXIe-1003-1 is a PXI Express, 1x4 multiplexing switching module that supports optical switching at wavelengths from 1,260 nm to 1,630 nm using single-mode fiber. The switch provides either SC/PC, FC/PC, SC/APC, … or FC/APC fiber-optic connectors. You can use the CohSol SwitchPXIe-1003-1 for repeatable, low-loss switching.
-
781316-01 -
NI
14-Slot, Virtex-5 LX85 FPGA, MXI-Express CompactRIO Chassis - The NI‑9157 is a rugged MXI‑Express chassis for high-performance, high‑channel‑count applications. With the NI‑9157, you can add C Series I/O modules to your PXI system or industrial PC. You can daisy chain up to six NI‑9157 chassis in a single chain and connect up to eight chains to a single controller.
-
781315-01 -
NI
14-Slot, Virtex-5 LX110 FPGA, MXI-Express CompactRIO Chassis - The NI‑9159 is a rugged MXI‑Express chassis for high-performance, high‑channel‑count applications. With the NI‑9159, you can add C Series I/O modules to your PXI system or industrial PC. You can daisy chain up to six NI‑9159 chassis in a single chain and connect up to eight chains to a single controller.
-
DAQStream -
Delphi Engineering Group, Inc
DAQStream is a family of high-performance data acquisition and processing systems that combine Delphi Engineering Group’s industry leading wideband digital receivers and StreamServer™ – multi-channel, streaming software for unparalleled high-speed data recording and processing performance. Delphi’s wide variety of FMC, FMC+, ADC and DAC modules enable DAQStream users multiple configuration options to meet the most stringent application requirements.
-
40-780A-522 -
Pickering Interfaces Ltd.
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
40-615A-013 -
Pickering Interfaces Ltd.
The 40-615A-013 is a 20-bank, 4-channel, 1-pole (SP4T) MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Copper Mountain Technologies
With our USB VNAs your automated test equipment works as one software system running on a single computer. We can customize the analyzer module to fit in your system, provide extra frequency range coverage as compared to our standard VNA models should you need it in your specific application or characterize the expected performance outside the frequency limits of our standard VNAs.
