Filter Results By:





sense, display, measures; gas, water, electricity, particles, vibration, light or quanta.

See Also: Sensors, Measurement

Showing recent results 4141 - 4155 of 4299 products found.

  • Instrumented Runway Visual Range Transmissometer System

    AGIVIS 2000 - Aeronautical & General Instruments Ltd.

    AGIVIS 2000 is a transmissometer-based Runway Visual Range (RVR) system that provides the highest possible levels of accuracy.The first generation of AGI RVR systems were developed in co-operation with the UK Met Office and CAA, and AGI has been supplying RVR systems for more than 25 years. AGIVIS 2000 systems are currently operational at major international airports certified for instrument landings up to and including CAT IIIB.AGIVIS 2000 is fully compliant with ICAO, WMO and CAA requirements. The system consists of transmissometer field sites, background luminance meters, runway lighting interfaces, data processing equipment and archive storage and backup. It can drive multiple full-colour dedicated RVR displays and may operate as a stand-alone system or integrated to an AWOS.Systems can be supplied fully installed with comprehensive engineering and operator training, and post-installation support is available worldwide.

  • LCR-Reader Probe Shielded Two-Wire Connector

    Siborg Systems Inc

    Siborg''s LCR-Reader Probe Shielded Two-Wire Connector allows to use LCR-Reader as a probe station. It also allows users to measure components that are beyond the tweezers allowable spread. The Connector is fully compatible with other tweezer-like meters in particular all models of Smart Tweezers. The kit comes with 7 different kinds of probes; 2 alligator clips, 1 longer pin-probe, 1 medium pin-probe, 2 multimeter 4 mm jack plugs, 1 spade connector. Each tip screws into the end of the connector cable. The LCR-Reader Probe Connector is simple to install: simply unscrew one of the gold-plated probes from LCR-Reader; place the flat side of the connector cable on the LCR-Reader''s probe arms with the gold flex cable and the connector cable''s flat end with two gold stripes. Return screws to the holes and start measuring.

  • Non-Contact Voltage Tester

    NCVT-3 - Klein Tools, Inc.

    Provides non-contact detection of AC voltage.Detects 12 – 1000V AC with simultaneous visual and audible voltage indicators.Bright flashlight illuminates work area and may be used independent of voltage detection function.Visual LED bar graph indicates the presence of voltage – the higher the voltage sensed, or the closer to the voltage source, the more LEDs light up.Bar graph visual voltage indicator utilizes up to five vibrant LEDs for easy interpretation/viewing.Audible voltage indicator beeps at a greater frequency the higher the voltage that is sensed, or the closer to the voltage source.“Auto Power-Off” conserves and extends battery life.Screw-thread battery cap with O-ring ensures protection against dust and water ingress.Lightweight, compact tool with pocket clip provides convenient storage and quick access.IP67: Dustproof and waterproof.6.6 feet / 2 meter drop protection.CAT IV safety rating for 1000V.Conforms to CE requirements.

  • Stages

    Aerotech, Inc.

    Aerotech manufactures a large selection of linear, rotary, and lift and Z-axis positioning stages that utilize our own brushless linear direct-drive servomotors, as well as ball-screw models driven with Aerotech brush or brushless rotary motors. Travels for our linear tables range from 25 mm to 1.5 meters. Aerotech''s positioning stages are utilized in high-performance applications in industrial robots, fiberoptics and photonics, vision systems, machine tools, assembly, semiconductor equipment, medical component laser machining, micromachining, electronic manufacturing, and other industrial automation applications. We even offer a complete line of nanopositioning stages that provide nanometer resolution, accuracy, repeatability, and in-position stability with travels from 25 mm to 160 mm. In addition, Aerotech manufactures drives and motion controllers that perfectly complement our positioning stages.

  • ST VL53L0X Time-of-Flight Range/Distance Sensor

    SEN-36003 - Playing With Fusion Inc

    Highly integrated breakout board for the ST Micro VL53L0X Time of Flight (ToF) range finder sensor, which builds on the absolute ranging technology introduced with the VL6180X. The VL53L0X drops the ambient light sensing capability of it's predecessor for a 10X improvement in absolute ranging capability, bringing the maximum possible range to 2 meters! As a result, this sensor has even more uses in the robotics, cell phone and gesture recognition space. The SEN-36003 includes the VL53L0X IC mounted between two 4-40 sized mounting holes with on board 2.8V LDO and high-speed signal translation to handle interface voltages from 3V to 5V. The board is interfaced via an I2C interface and function pins have been broken out to a 0.1" pin header. All pins are translated to allow interfacing with any microcontroller in the 3V to 5V operating range.

  • Surface DC Voltmeter

    SVM2 - Alpha Lab, Inc.

    The SVM2 has high sensitivity (resolution), and can detect even a 1 volt charge anywhere within its full range of +29,999 to -29,999 volts. Thus it is easy to measure whether a given process is increasing or decreasing the static electricity present, even if the increase or decrease is by a tiny fraction. The meter reads the actual static signal, but it also captures and stores the highest positive and highest negative signals that were experienced since the last time that the "Reset" button was pressed. These peak + and can be displayed at any later time. The peak function has a "window" time of 0.005 seconds (which is much faster than the display) so even very quick peaks are captured and stored. There is also a user-settable alarm. The alarm will sound if the signal (whether + or -) ever exceeds the value set by the user for at least 0.005 seconds. The alarm can be reset or muted at any time.

  • Trace Level Chemiluminescence NO-NOy Analyzer

    Model T200U NOy - Teledyne Advanced Pollution Instrumentation

    The Model T200U NOy analyzer has been developed and refined specifically to address the challenges of NOy monitoring as required, for example, in the US NCore network. It uses the proven chemiluminescence principle and is coupled with a remote NOy converter via umbilical to allow measurements with a lower detectable limit of 50 ppt.The Model T200U NOy analyzer combines a gold plated reaction cell with an enhanced performance pump, special low noise photomultiplier tube, and unique signal conditioning to provide exceptional sensitivity. In addition, a pre-reactor separates the NO-O3 reaction from background chemiluminescence to allow accurate auto-zero of the analyzer. The remote NOy converter is provided with a stainless steel, NEMA 4X (IP65) enclosure and custom sample umbilical to allow a mounting height of 10 meters. In addition, the converter features a unique purge circuit designed to remove residual calibration gas.

  • UPS (Uninterruptible Power Supply)

    Allied Edison LLC

    The UPS (Uninterruptable Power Supply) by Allied Edison is a light weight (7.2 lbs), portable, non-variable source that converts  a 12 Vdc Lithium Ion battery to output 110 vac sine wave at 60 hertz. It also has four 12Vdc output jacks, and 4 USB ports to power electronic equipment such as computers or used to supply cell phone chargers, etc. It has a strong built in flashlight. The UPS plugs into a standard 120 Vac, 60 hertz receptacle for charging and indicates percent battery capacity remaining on a digital meter located on the front panel. The UPS can also be charged by a solar cell, sold separately or can be plugged into a vehicles cigarette lighter receptacle for use in remote areas. The UPS is an excellent compliment to the VS-3 power supply where a technician needs a variable AC/DC source and cannot run a power cord due to the remoteness of the work area.

  • Geiger Counters

    PCE Instruments

    A geiger counter detects nuclear radiation by measuring the emission of ionizing radiation of alpha particles, beta particles and gamma rays. Also referred to as a radiation detector, a geiger counter consists of two main elements: the processing electronics and the geiger tube. The geiger tube is filled with low-pressure inert gas like helium, argon or neon. If radioactive radiation occurs, the inert gas is ionized. An anode within the geiger tube registers the quantity of ionized particles numerically correlating with the strength of the radioactive radiation. The radioactivity measurement is then displayed on the LCD screen of the geiger counter or radiation detector.It is very important to measure radioactivity as well as to classify radioactivity values. For example, terrestrial gamma radiation is measured according to general values from 0.03 - 0.3 µSv/h (microsievert / hour). This "normal" oscillation range is conditioned by natural radioactive elements in the ground such as uranium and potassium. To calculate this factor, one must take into consideration cosmic radiation. For example, when considering cosmic radiation, the maximum radioactivity content at Schneefernerhaus, the highest-located German environmental research station, is approximately equal to 110 µSv/h.At PCE Instruments, you will find three types of geiger counter or raditation detection devices to help you measure radioactivity: 1) alpha radioactivity meters, 2) meters for detecting alpha, beta and gamma radioactivity and 3) radioactivity meters for human beings.

  • Fluke Test Equipment


    Fluke Test Equipment includes electrical test equipment, environmental test equipment, mechanical test equipment and more. Fiberinthebox supply a large range of Fluke Test Equipment, such as Fluke Fluke NetTool Inline Network Service Kit, Fluke Networks AirCheck Wi-Fi Tester, Fluke Networks Cable Strippers, Fluke Power Meter, Fluke Power Analyzers.

  • Capacitance Tester


    Is a piece of electronic test equipment used to measure capacitance, mainly of discrete capacitors. Depending on the sophistication of the meter, it may display the capacitance only, or it may also measure a number of other parameters such as leakage, equivalent series resistance (ESR), and inductance. For most purposes and in most cases the capacitor must be disconnected from circuit; ESR can usually be measured in circuit.

  • Density (Densitometer)

    MRC ltd.

    The oscillating U-tube densitometer method is a technique to determine the density of liquids and gases based on an electronic measurement of the frequency of oscillation, from which the density value is calculated.Density meters work by measuring the oscillation of a glass tube containing the sample.Specific gravity and refraction index can be measured. They are used in many industries such as: oil, chemical, food and beverage industries for quality control and research and development.

  • Moisture Test Chamber

    Thermotron Industries

    The chamber features a self-contained water recirculation system that eliminates the cost and inconvenience of plumbing in a facility water supply. Water is injected into the test enclosure through specifically-sized nozzles. Flow meters with adjustment valves supply the spray at specified flow parameters. A rotating test platform can be incorporated to promote even moisture distribution over the surface of the products under test.

  • Current To Pressure Measurement Trainer

    UITM-17 - Unitech Scales And Measurements Pvt. Ltd

    Pressure to Current (P to I ) Trainer:This setup comprises of pressure chamber fitted on a base board. A pressure transducer and bourdon pressure gauge are fitted to the chamber. Digital pressure indicator with transmitter output is provided to display the pressure sensor by the pressure transducer. Transmitter output 4 to 20mA can be measured by a current meter. Foot air pump is provided to build the pressure.

  • 500 AMP Carbon Pile Load Tester

    710 - Electronic Specialties Inc.

    The #710 will perform variable load testing on 12 volt batteries rated as high as 1000 Cold Cranking Amps. Use this battery tester to simulate actual cranking loads. Also tests alternator charging voltage and relative starter current draw. The #710 features large dual meters to display the battery voltage and load current simultaneously, during the test.