Showing results: 8731 - 8745 of 10608 items found.
-
LT-4123 -
Lambient Technologies
The LT-4123 Liquid Dielectric Test Cell is designed for testing the quality of materials such as the insulating oils used in transformers and the resins used in the manufacture of thermosets. With the LT-4123 Liquid Dielectric Test Cell, users can measure the AC loss characteristics and permittivity of liquids. The data gleaned from these measurements are used to set quality benchmarks for fluids during testing and manufacturing.
-
RPT-5 -
DeltaTech Electronics
The RPT-5 device is used for performing an independent, parallel pressure measurement in storage fuel systems such as Common Rail (Diesel) and GDI/FSI (petrol). The tester, apart from pressure value, also diagnoses power supply of a sensor. Additional advantage is the capability of automatically detecting the terminals of the sensor, which is useful especially when using needle probes.
-
MEXA-584L -
HORIBA, Ltd.
The MEXA-584L simultaneously measures CO, HC, CO2 (non-dispersive infrared: NDIR) and air-to-fuel ratio (AFR) or excess air ratio (A) in idle state. lt optionally measures O2, NO, engine speed (RPM) and oil temperature (TEMP). Lightweight and compact with a clear LCD and effortless operation, it can be used as a simple measurement instrument in any work situation.
-
RESON TC 4035 -
Teledyne Marine RESON B.V.
The TC4035 is a miniature probe hydrophone specifi cally designed as a standard reference hydrophone for sound measurements in the frequency range 100 to 500kHz. The hydrophone incorporates a 10dB low-noise preamplifier, which includes an insert calibration circuit for convenient electrical testing of the hydrophone condition. The pre-amp has a drive capability for cable length up to 25 meters.
-
3λ-PM -
Notice
•Simultaneous wavelength detection and calibration.•B / E / G – PON 3 wavelength power meter and insertion loss tester (1310 / 1490 / 1550 nm)•Simultaneous measurement of 3-wavelength PON signals•Automatic wavelength detection to save time and cost•Rugged, shock and water-proof for field use•Compact, lightweight and cost-effective•Quick and easy to operate
-
Mode Stir -
MVG EMC
Our mode stir chamber or reverberation chamber is particularly suited for immunity testing for EMC measurement and special applications for very high-field strength applications (200V/m - 7000V/m). The paddle system ensures that the widest range of frequencies and particularly low frequency performance is maximized. This system meets testing requirements of the IEC61000-4-21 EMC testing specification.
-
Universal Wireless Tester -
NOFFZ Computer Technik GmbH
Wireless communication standards are increasingly integrated into vehicles as well as smart home and Internet-of-Things applications. They form the basis for connected services, advanced HMIs, and autonomous driving. The combination of constantly evolving standards and the integration of multiple wireless technologies with many RF channels into new product designs means that measurement speed and quality are becoming a priority.
-
MIG0603CLV1 -
EMC Partner AG
The MIG0603CLV1 is a generator for testing varistors. It has circuits with three different source impedances and up to 11 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 200A which is maintained over the entire load range.
-
PX32103 -
LinkedHope Intelligent Technologies Co.,Ltd.
Based on Intel® 3rd Generation Core™ i7 and Celeron® processors, PX32103 is a high-performance PXI system controller up to 4x2.3GHz 8 threads. Low power consumption (maximum of 65w) and thermal solution design guarantee working stability and reliability of PX32103, making PX32103 applicable for multiple environments test and measurement applications.
-
GM8019 + GM83001E -
UC Instruments, Corp.
The UC INSTRUMENTS GM8019 + GM83001E 1310/1550 nm dual laser source back reflection meter and power meter is a compact, direct display instrument for the convinent measurement of backreflection, insertion loss and power connector, fiber optic components, and system. With a single output port, the meter is very easy to use and ideal for fiber cable jumper manufacturers.
-
SITEX SCU286 -
Teledyne ICM
The SCU286 has a system for direct measurement of the high voltage delivered by the X-Ray generator to guarantee the accuracy of the radiological parameters. Based on this data the control system maintains the stability of mA and kilovolts to within ± 0.5% in any selection range.SITEX & XS units offer a totally constant quality of exposures, as they are virtually exempt from fluctuations in the power supply.
-
Model 91091 -
Coaxial Dynamics
The Coaxial Dynamics 'Digital Wattchman' Rack Mounted Station Monitor/Alarm is similar in function and appearance to our 81090 Series except it is designed for the accurate measurement of complex RF Waveforms such as CDMA (Code Division Multiple Access), DAB (Digital Audio Broadcast), DTV (Digital TV) and HDTV (High Definition TV), as well as CW, AM and FM.
-
ADLINK Technology Inc.
From entry-level to high-end, data acquisition to digital input/output, ADLINK provides a diversity of modular instruments with market-leading price/performance ratio, for bigger and better measurement and automation systems. Now high-speed digitizer, switching, simultaneous data acquisition, high-density multi-function data acquisition, analog output, digital multimeter, and arbitrary waveform generator categories are all available.
-
Guided Wave
The sample interface is a virtual “windows into the process” and is a critical component of any optical analyzer system. Guided Wave sample interfaces (probes, flow cells) are designed for use with NIR or UV/Vis fiber optic coupled analyzers. They are designed to be rugged and reliable in harsh chemical and physical process conditions while providing optimal transmission for long-term reliable measurements.
-
COMBI519 -
HT Italia Srl
COMBI519 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.