Showing results: 196 - 210 of 264 items found.
-
GAO Tek Inc.
Gloss meters are used devices designed for measuring the specular reflection gloss of a surface. The gloss is determined by the measuring of the amount of reflected light at an equal, but opposite angle from the light beam. The quantity of light is determined by shining light from a defined angle at a surface and then measuring the light opposite the source of light at the same angle. The measurement is then compared to a standard. The most common angle for measurement is 60°.
-
International Light Technologies
If you are using a UVC light-based disinfection system you are probably scrambling to deploy tools to combat the COVID-19 outbreak. Increasingly facilities are looking to disinfect everything including air, surfaces, instruments, and personal protective equipment (PPE) using UV-C light. Verifying the intensity of the light, or dose, reaching the target is a critical step in validating that the correct UV dose is being applied to ensure proper decontamination.
-
24-400xg -
JFM Engineering
The 24-400XG is an instrument designed to charge, trickle charge and analyze (discharge) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries.With its multiple modes of operation of Constant Current Charge (dual and single rate), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge (analysis), Resistance Discharge (analysis) and Full Discharge (deep cycle), the 24-400XG can satisfy the requirements of most small (0 to 10 A-hr) rechargeable battery systems.The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit (no load) and Overvoltage conditions.Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights inform of the status of the operation.
-
LAP GmbH
A glowing hot wire is pulled through the rolling mill at about 120 meters per second during ongoing production. Speed, high temperatures and dirt are special challenges for a high-precision measuring system. Our solution is the Contour Check Wire. It is specially designed for the geometric measurement of wires, rods and rebar and, at 800 Hz, offers the optimum measuring rate for accurate data acquisition. In the uniaxial version, you can check the diameter; in the two- to three-axis version, the ovality can also be determined. The small dimensions and light weight allow a quick and easy integration of the Contour Check Wire into the existing line.
-
CDMS-1000 -
Focused Photonics Inc.
CDMS-1000 is designed with light scattering technology for continuous real-time measurement of particulate concentration along with noise and meteorological parameters. This combination consists of a particle analyzer, camera, sound level meter, and GPRS module.
-
F-750 -
Felix Instruments
The F-750 Handheld Brix & Dry Matter Meter uses near-infrared (NIR) spectroscopy to estimate quality metrics such as dry matter, Total Soluble Solids (TSS or brix), titratable acidity, and color. Working like a high-powered flashlight, the F-750 sends particles of light into a commodity, then measures the NIR light interactance with molecular components inside of the commodity to quantify user-selected traits. The F-750 has a wide range of applications, from determining optimal harvest timing by assessing fruit maturity, to providing an objective analysis of produce quality of fruit in packing houses and upon import. The F-750 is a handheld, fully integrated system, allowing users to operate it out in the orchard or inside the QA lab. Its simple, intuitive user interface makes it easy for anyone to use, while its model building software makes it customizable and versatile.
-
GUVx-T1xS7-LA9-H -
Genicom Co., Ltd
High Power UV Intensity Meter (Max. 10 W/㎠. Applications: UV Lamp Intensity & Aging. High power UV LED intensity measuring of Curing system. UV light transmittance measurement. Spectral Detection Range: 230 - 445 nm.
-
LD-LTSS-A10 -
Labodam
TSS meterLD-LTSS-A10is a tabletop meter with a dual-beam infrared scattered light photometerdetection system for enhanced stability. Built-in self-diagnosis function to ensure dataaccuracy. Optional cleaning brush for automate cleansing function to reduce the sensormaintenance.
-
Dymax Corporation
UV Intensity Meters & Visible Intensity Meter for Light Curing Systems. Dymax UV and visible radiometers are simple to operate and allow operators to monitor and document a UV/Visible light curing process. A low UV/Visible intensity measurement signals an operator to replace the bulb, reflector, or lightguide. Radiometers can also be used to confirm that operators are properly shielded from UV/Visible exposure. Degradation of curing bulbs, lightguides, and reflectors can decrease intensity, resulting in incomplete cures.
-
Extech EN100 -
Extech Instruments Corporation
The EN100 is a Compact Hygro-Thermo-Anemometer with Light Sensor. 11-in-1 Environmental Meter for indoor and outdoor conditions. Built in light sensor measures light level. Auto-rotating display depending on selected function. Also measures Air Velocity, Air Flow, Temperature, Humidity, Wet Bulb, Dew Point, Heat Index, Wind Chill, Barometric Pressure and Altitude. Complete with built-in multiparameter sensors, wrist strap, and CR2032 battery.
-
Extech 45170 -
Extech Instruments Corporation
This 4-in-1 meter measures Humidity, Temperature, Air Velocity and Light. The dual LCD simultaneously displays Temperature and Air Velocity or Relative Humidity. High Temperature air or surface measurements can be made using the built-in Type K input. Comes complete with built-in Humidity sensor, Light sensor and Vane wheel, wrist strap, and 9-Volt battery.
-
Extech LT40 -
Extech Instruments Corporation
The LT40 LED light meter is useful for measuring and optimizing environmental light levels in a wide range of environments, including office buildings, manufacturing plants and warehouses, university campuses, schools, hospitals, and many other locations. OSHA regulates workplace lighting because illumination must be adequate for assigned tasks, and light meters are used to verify regulatory compliance, as well as state and local public safety codes and ordinances. Use of LED lighting is on the rise because it is more efficient to operate, it emits stable, high quality illumination, and the technology is dropping in price. Besides LED lighting, the LT40 can measure standard light sources fluorescent, metal halide, high pressure sodium and incandescent up to 400,000 lux (40,000 Fc). The LT40 comes with a built-in sensor with protective cover, 2 AAA batteries, storage pouch, and user manual.
-
Extech LT300 -
Extech Instruments Corporation
Insufficient lighting can create security risks or result in OSHA crackdowns. The Extech LT300 light meter can determine whether you have adequate illumination to protect workers, students, visitors, patients or attendees of different venues. This handheld instrument measures up to 40,000 Fc (or 400,000 Lux) utilizing a remote light sensor connected via 12 in. coiled cable (expandable to 24 in.). A prominent LCD readout displays a digital calculation and complementary analog bar graph for quick, reliable assessments. Complete with 9V battery, light sensor with protective cover, protective holster, and soft case.
-
Extech 407026 -
Extech Instruments Corporation
This 407026 Heavy Duty Light Meter has 4 lighting type settings for enhanced accuracy (Tungsten/Daylight, Fluorescent, Sodium, Mercury). Additional features include Data Hold, Min/Max/Average, Auto power off and a % reading of the differential from a reference point. Built-in RS-232 interface with optional Data Acquisition Software and Data logger. Complete with 9V battery, light sensor with 45" (1.1m) cable, protective cover, and holster with stand.
-
Extech UV505 -
Extech Instruments Corporation
The Extech UV505 pocket-sized UV light meter measures UV-AB light from natural and artificial light sources used in outdoor activities and indoor medical testing, laboratory/research, industrial, education, electronics, and forensics/criminology applications. It offers a backlit display, cosine corrected sensor, two selectable ranges, zero function, display hold, and auto power off. Includes a pouch to protect and store your meter.
