Showing results: 2836 - 2850 of 3752 items found.
-
Becker & Hickl GmbH
Designed and manufactured by Becker & Hickl – bh delivers prominent picosecond diode lasers with wavelengths from the NUV to the NIR. All bh pulsed diode lasers work with simple +12V power supply or pull their power from the USB port of a PC or Notebook Computer. Other features are high repetition rate, short pulse width, unprecedented timing and power stability, and extremely low electrical noise level.
-
Mors Smitt Group
Are solid state voltage sensing relays with electromechanical output contacts built in a fully draw out case format. Designed for application on AC & DC voltage systems, these relays are ideally suited to monitor power supply voltage levels wherever high accuracy and reliable, maintenance free operation is essential. All power to operate the relays is derived from the sensed input voltage therefore an auxiliary supply is not required.
-
AF-OLK5NNextGen Series -
Advanced Fiber Solutions
The AF-OLK5NNextGen series test kits are the latest addition to the AFS product family. This inexpensive optical test kit is the complete solution necessary for the installer to test and trouble shoot both multimode and single mode fiber optic systems. These test kits are designed to allow testing of all parameters of fiber optic networks, including output power levels from the fiber, coupled source power and attenuation loss in a cable.
-
DURST Motor & Electric Industries Pty Ltd.
DURST Measurement & Diagnostic Products; circuit tester, vehicle battery analyzer, multimeter, dedicated automotive multimeter, clamp meter, sound level meter, oxygen sensor tester, diesel engine tachometer, multisystem ignition analyzer, faultfinder, circuit tester, diode tester, regulator tester, growler for testing motor insulation, armature/commutator tester, diagnostic testers, current clamps, optical photo/contact tachometer, etc.
-
Huntron® Trackers® -
Huntron
Adding diagnostic tools to enhance your circuit board test capabilities is an important part of any electronic repair environment.Huntron Tracker power-off circuit board test uses analog signature analysis to detect and isolate component faults on boards beyond power-on functional testing. By comparing Tracker signatures from a working circuit board to the signatures of a non-working board, you can troubleshoot down to the component level.
-
FIME SAS
FIME laboratory equipment qualified for RF testingValidate the analogue behaviour of RF devices with a single set of laboratory tools and services before seeking contactless Level 1 type approval or launching mass production. FIME RF test benches are built for RF testing of: EMV contactless cards and readers; ICAO e-passports and readers; ISO devices (PICC and PCD), HF and UHF RFID tags and readers.
-
Si-CA 8500 -
Sauermann Group
Accurate, reliable, robust & fast, the Si-CA 8500 Combustion Analyzer is the most powerful and advanced portable emissions analyzer on the market. Complete portable tool for emissions level monitoring of boilers, engines, and other combustion equipment, this emissions monitoring device can boast as many as 9 gas sensors, detecting one of the widest spectra of gases: O2, CO, NO, NO2, SO2, CO2, CxHy, High CO, VOCs and H2S.
-
UVISEL Plus In-Situ -
HORIBA, Ltd.
The UVISEL Plus in-situ spectroscopic ellipsometer can be easily mounted on process chambers (PECVD, MOCVD, sputter, evaporation, ALD, MBE) for the real-time control of thin film deposition or etch processes.The UVISEL Plus in-situ provides the unique combinations of very high speed, sensitivity, dynamic range and accuracy making the instrument able to control deposition / etch at the atomic layer thickness level, even for rapid processes.
-
VME850P2 -
Silicon Control Inc.
The VME850P2 analyzer is an optional plug on module for the VME850 analyzer that adds analyzer and exerciser functions to the VME850 analyzer for the P2 connector. This module allows the user to monitor and stimulate the A, C and D rows of the 160 pin P2 connector. Although the VME850P2 analyzer is in a PMC form factor it is not compatible with the PMC protocols and signaling. The signaling levels on the P2 connector must be less then 5V in order to prevent damage of the analyzer.
-
IST Engineering, INC.
Burn-in generally involves the extended operation of a product in a temperature-controlled environment. With possible humidity and supply voltage margining - the burn-in process can then be extended to include power stress (levels and on/off cycles) tests, high humidity environmental simulation as well as the classic "four corner test" of high voltage + high temperature, high voltage + low temperature, low voltage + high temperature and low voltage + low temperature.
-
AMI D9650 -
Nordson Corporation
Specifically designed to serve as a general purpose tool for failure analysis, process development, material characterization and low volume production inspection, the capabilities of the D9650 are truly unmatched. Representing the latest in C-SAM acoustic micro imaging, the D9650 delivers the unrivaled accuracy and robustness that you would expect from Nordson Test & Inspection instruments, plus improved electronics and software that raises the performance level for laboratory acoustic microscopes.
-
Extech CO240 -
Extech Instruments Corporation
The CO240 measures Carbon Dioxide (CO2), Air Temperature and Humidity, as well as Dew Point and Wet Bulb calculations. The user settable high alarm with audible beeper is perfect for conducting a quick check of CO2 level to help adjust the environmental conditions in an enclosed area, such as a greenhouse or nursery, to insure optimal plant grown. Complete with six AAA batteries, USB cable, PC software and soft case.
-
MasterFiller -
JFM Engineering
The MasterFiller is an instrument designed to deliver measured quantities of distilled water as required in the service of Aircraft Nickel-Cadmium batteries.· The MasterFiller consists of a microprocessor controlled pump with a level sensing probe, a keypad and display and an external 12VDC power supply (or optional battery).· The MasterFiller is part of a system comprising Intelligent Charger-Analyzers and Software for Battery Data Acquisition and Analysis, designed to improve the accuracy and efficiency of the process of testing batteries for airworthiness certification.
-
Sierra M122A -
Teledyne LeCroy
The Sierra M122A is Teledyne LeCroy’s two port SAS / SATA analyzer with special licensing to allow 6 Gb/s protocol capture. This multifunction platform is available with an integrated traffic generation option capable of host and device emulation. There is also a “Jammer” option for stress testing at the system and component level. This model of the Sierra M122A is configured for 6Gbps SAS & SATA protocol capture and can be field-upgraded to support 12Gb/s SAS testing.
-
MaxiWave® -
Sercel Group
MaxiWave® is the most cost effective digital multi-level downhole seismic array for very large sized downhole seismic surveys. With 100 digital 3-components levels, MaxiWave® benefits from the most advanced developments in terms of real time telemetry and mechanical reliability, that make the system the optimal solution to address today’s challenges for cost effective acquisitions with high volumes and high quality data.
