Filter Results By:

Products

Applications

Manufacturers

LCD

Analyze Liquid Crystal Displays.


Showing results: 916 - 930 of 1368 items found.

  • Automotive Emission Analyzer

    MEXA-584L - HORIBA, Ltd.

    The MEXA-584L simultaneously measures CO, HC, CO2 (non-dispersive infrared: NDIR) and air-to-fuel ratio (AFR) or excess air ratio (A) in idle state. lt optionally measures O2, NO, engine speed (RPM) and oil temperature (TEMP). Lightweight and compact with a clear LCD and effortless operation, it can be used as a simple measurement instrument in any work situation.

  • Mini Digital Multimeter

    HH2103 - Colluck Company Limited

    Basic Accuracy 1.0%. LCD display 2000 count, 12.8mm figure height. Manual Ranging at your choice (19 Range). Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 2000KΩ. Diode test. Square Wave Signal Injection

  • High Resolution Precision Milliohm Meter (220VAC) - Benchtop Meter Provides Resolution Down to 0.01mΩ

    Extech 380562 - Extech Instruments Corporation

    Compact and precise, the Extech 380562 Milliohm Meter has 7 ranges and measures down to 0.01mΩ using 4-wire Kelvin clip test leads. Measurements are displayed on the unit's large 0.8", 1999-count LCD. Built-in comparator for Hi/Lo/Go resistance testing or selection. Complete with 4-wire cables with Kelvin clip connectors and power cord.

  • 100KHz LCR Meter

    MCH-2817 - MCH Instruments Co.,Ltd.

    Is a high accuracy, wide measuring range impedance tester. With test frequency upto 100kHz, three test signal levels and capacity of measuring parameters such as Resistance(R), Capacitance(C), Inductance(L) and etc. It's equipped with a 240 × 128 dot , back-lighted LCD display which provides user friendly interface for measurement and operation.

  • Computer system control Elmendorf Tearing Tester

    SKZ156B - SKZ Industrial Co., Ltd

    It is suitable for the determination of tear strength (Elmendorf Method). It adopts single chip for data detection and processing, pneumatic component performance process control, large-sized LCD dot matrix display screen, which prompts operation procedures and tests data. With serial and parallel output, it can output the detection report via printer, and also get connected with the computer.

  • Digital Inspection Cameras

    Maxivideo MV208 - Autel

    This premier Autel MaxiVideo MV208 digital videoscope is an ideal tool for examining difficult- to- reach areas normally hidden from sight. It features the ability to record digital still images and MPEG2 or MPEG1 videos either on its internal flash memory or on the removable Micro SD Card(Optional). The ergonomic tool not only features a 2.4" full color LCD screen, auto focus and viewing capacity as close as 1" with crystal clear output, but also offers the capability to stream digital video directly to a PC. The Multipurpose Videoscope is an economical solution to inspect machinery, facilities and infrastructure in the safest, quickest and most cost-effective manner possible.

  • Digital Inspection Cameras

    Maxivideo MV400 - Autel

    This premier Autel MaxiVideo MV400 digital videoscope is an ideal tool for examining difficult- to- reach areas normally hidden from sight. It features the ability to record digital still images and MPEG2 or MPEG1 videos either on its internal flash memory or on the removable Micro SD Card (Optional). The ergonomic tool not only features a 3.5" full color LCD screen, auto focus and viewing capacity as close as 1" with crystal clear output, but also offers the capability to stream digital video directly to a PC. The Multipurpose Videoscope is an economical solution to inspect machinery, facilities and infrastructure in the safest, quickest and most cost-effective manner possible.

  • Fiber Endface Inspector

    CA-EASYGET - UC Instruments, Corp.

    The CA-EASYGET fiber endface inspector is the masterpiece of our engineer which withexcellent performance and convenient operability, trust it is the best choice for fiber endface inspection. Taking use of 220k pixel of TFT sharp and finely LCD, which magnify about 200 times of object, it makes you easier to judge the status of fiber endface. And its compact size made it ideal tool of connector endface inspection before fiber network installation, varies of adapters meet different requirements on inspect male fiber connectors&female fiber connectors, such as FC SC ST E2000 LC MU and TOSA ROSA fiber endface.

  • Fully Automatic Transformer Oil Test Set

    OTS-A series - The Motwane Manufacturing Company

    OTS-A series is fully automatic microprocessor based transformer oil test set designed with advanced features to measure breakdown voltage of insulation oil accurately. The OTS-A Series preprogrammed with worldwide acceptable standards.The user can define customized standards. The large LCD display with menbrane key pad for easy operation. It is provided with internal memory for 100 data storage & built-in thermal printer for onsite report. The kit is protected by automatic detection of poor input ground.The acrylic oil test vessel provided with adjustable electrode gap setting. The voltage calibrator for on site calibration saves cost & time of user.

  • LCR Meter, Hand Held, 100 kHz, 2 kH, 20000 µF, 0.2 Gohm

    72-10465 - Tenma

    The 72-10465 from Tenma is a LCR meter in orange and grey colour. It features an easy to read dual LCD (40mm x 63mm) display measurement of 19999/1999 (main/auxiliary). It also has series and parallel measurement modes which can be used to select quality factor, loss factor, phase location angle and equivalent resistance of measure articles. Intelligent detection and five different test frequencies enable accurate readings for all sizes of capacitors and inductors. The user can also access the stored data on a PC with the included USB connection and interface software. The compact size and case make this unit far more portable than a benchtop meter.

  • Open Circuit Locator

    A994 - AGM Elettronica

    The A994 is an open circuit locator for electric and telephone cables wind on the reel; it gives the position of the fault from the inside or outside end of the cable, in percentage to the total cable length. The instrument measures the ratio of the capacitances of the two sections of failed conductor using two high precision i/v converters. The advantage of this method is due to the fact that the measurement error depends almost exclusively on the dimensional inhomogeneity of the cable. The A994 has the unique feature to permit the location of fault in cables with all broken wires. This instrument locates breaks in cables with a total capacity between 2 nF and 5 uF. The distance to fault is displayed on a large LCD display.

  • Short Circuit Locator

    A694 - AGM Elettronica

    The A694 is a short circuit locator designed for fault location in metallic cables. The instrument measures the ratio of the resistances of the two sections of failed conductor using a four-wire "Kelvin" connection, thus eliminating errors associated with contact resistances of the test leads. With the A694 you can determine if the cable has more than a short and locate the first and the last fault. The instrument locates fault with an insulation resistance up to 5 Mohms in cables that have a total resistance greater than 0.1 ohm and less than 40 kohms. The distance to fault is measured as a percentage of the total length of cable and is displayed on a large LCD display.

  • Wood Moisture Meters

    PeakTech Prüf- und Messtechnik GmbH

    High quality wood and material moisture meter, which is characterized by its ease of use and universal applicability. The device has an LCD display, in which measured values ​​of humidity and ambient temperature are displayed. In addition, it is equipped with an LED display, which enables a quick good-bad assessment of the measured values. When burning wood in a wood-burning stove with a high moisture content, the efficiency of the stove decreases, while at the same time the emission of pollutants, such as soot and fine dust, increases. In addition, there is a build-up of soot in the chimney, which can lead to a fire. Therefore, this device is ideal for wood storage, control during the heating season or use in construction.

  • Thermistor Power Meter

    N432A - Keysight Technologies

    Keysight N432A is the replacement for Keysight's legacy 432A analog thermistor power meter. The single-channel, average RF power meter operates with the Keysight 8478B and 478A thermistor mounts. The N432A-and-thermistor-mount pair is ideal for applications that require high measurement accuracy, particularly in metrology and calibration laboratory environments. The enhanced thermistor power meter comes with a digital color LCD display, and user-friendly front panel interface. Its built-in calibration factor table provides a more convenient and accurate method of storing calibration factors as compared to the old knob-turning approach of the 432A. The N432A is LXI compliant, and programmable via GPIB, USB and LAN.

  • On-line UPS, Rackmount & Tower 700VA To 3kVA

    SC Series - Falcon Electric, Inc

    *Reliable, online UPS. When deciding on a UPS solution, be aware of the UPS type. The SC is an online UPS, meaning its inverter is always “on” to provide new, clean AC power.*User-friendly LCD display. The SC UPS has an easy-to-use display for quick access to UPS status, battery and load levels – and more.*Advanced communications. The supplied software supports unattended shutdown and UPS management. An optional SNMP/HTTP agent board is available.*Rack/Tower configuration. Simply rotate the LCD display on a rackmount model to use as a tower UPS.*User-programmable frequency converter. The SC UPS is easily programmable as a 50 or 60 Hz frequency converter.*Falcon is recognized for quality and reliability. Falcon Electric is a leading manufacturer of reliable online UPS for over 30 years. Our technical expertise assures you find the right solution – the first time.

Get Help