Showing results: 451 - 465 of 851 items found.
-
PP401 -
Matco Tools
*Electronic circuit and component tester that supplies battery ground and power along with 8 diagnostic testing modes to provide automotive technicians with detailed information on the circuits and signals being tested*Diagnostic Modes include: AC/DC Voltmeter, Ohmmeter, Frequency, Pulse width (Positive and Negative) Fuel Injector Tester, PCM/ECM Driver Tester and PPECT3000 Signal tracer*Tests for AC/DC voltage in 100ms and 50s resolutions, AC volts RMS and volts peak-to-peak, measure resistance, frequency and pulse width (negative and positive)
-
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2710 is a residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE). RCD testers let a fault current flow and thus determine at which fault current the RCD triggers. The tripping time is also measured. These two parameters, tripping current and tripping time, are the safety-relevant parameters of an RCD. The various selectable test currents and characteristics that can be set with this device make the PeakTech 2710 the ideal companion for every electrician.
-
Freese Enterprises Inc.
Freese Enterprises (FEI) has vast experience, in many industries, in the custom design and construction of physical test fixtures to consistently test a feature or operation of a device or piece of software. FEI can develop test solutions for modules or fully assembled products such as key fobs, RF filters, and cell phones - from complex integrated circuits and custom electronics to automotive components and RF communication devices. In general, the advantages of FEI test fixtures include the separation of the test initialization and destruction from the testing, reusing a known state for more than one test, and assumption by the testing framework that the fixture set-up works.
-
MPK-253 -
MEGABRAS srl
The MPK-253 digital very low resistance ohmmeter is a portable, microprocessor-controlled instrument used to accurately measure resistances of switches and circuit breaker contacts, transformer and motor windings, wire and cable samples, joints in busbars, etc., using test currents from 1mA up to 10 A.
-
AVJoG Rack -
CableJoG Ltd
*A single box solution for testing AV cables. *Easy to use with only one button operation. *Detects Open, Short and Crossed circuits. *LCD display for test results. *All major AV connectors present, no need for extra adaptors. *40+ preprogrammed cable types.
-
OMICRON electronics
The Primary Test Manager™ (PTM) software supports you during diagnostic testing, condition assessment and data management of medium- and high-voltage assets, such as circuit breakers, rotating machines, grounding systems, instrument and power transformers as well as bushings and on-load tap changers (OLTC).
-
QT-8000 Series -
PowerTECH Co,Ltd.
Tester is applicable to regularDC/AC parameter testing and IC device performance testing. Main application: Power Management; Digital Consumer Products; Communication& Interface; Automotive; Energy Conservation electronics; Standard Linear Circuit; Memory; CPU Chips; Special Customized IC and Wafer Test.
-
CBV-19 -
Zensol Automation Inc.
We conceived the CBV-19 to provide the best range of testing for electrical facilities such as circuit breakers (using gaz, oil, air, vacuum…) or synchronous condensers all the way up to 800kV and more. It combines Timing, Motion, Dynamic Resistance Measurements, and Vibration, all in a single test.
-
CBV-32 -
Zensol Automation Inc.
We conceived the CBV-32 to provide the best range of testing for electrical facilities such as circuit breakers (using gaz, oil, air, vacuum…) or synchronous condensers all the way up to 800kV and more. It combines Timing, Motion Dynamic Resistance Measurements, and Vibration, all in a single test.
-
Langer EMV-Technik GmbH
Used for EMI suppression in printed circuit boards during the development phase. The developer can use the E1 set to quickly identify the causes of burst and ESD interference. This allows the developer to design suitable measures to solve the causes of the interference. It can also be used to test the effectiveness of the measures taken.
-
AC, DC, AC and DC -
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Panel mounted controls & indicators with easy to read legend.• Continuously variable output from zero to full voltage.• Low end ground test.• Multi range analogue kV meter and current meter.• Fast acting overload circuit breaker.• Zero start interlock.
-
TEL5 -
Standard Electric Works Co., Ltd
● Fast, easy wiring check.● Easy to read light indication.● Confirm the correct wiring of AC socket.● Test GFCI for correct wiring & operation.● Detect 5 wiring faults.● GFCI circuit trips to confirm the tester is working.● The testing current for GFCI is about 8mA.
-
KT-200SG -
Kast Eng Co. LTD.
This test instrument stands for the EMI(Electro Magnetic Immunity) ability test to the electric devices, electronic circuit boards & electric equipments. Recently this instrument is widly used in many companies in Korea & other countries to test the immunity to thier products-power supply, drive PCBs, communication systems, LCD display panels whether they are safe or not against the impulse & noise.All for the purpose, of this object, it generates 4 ~ 5 kinds of different impulse test waveforms.Output test voltage level : 5 ~ 200 V ImpulseOutput voltage polarity : Positive, NegativeType of waveforms
-
Circuit Wizard - CW409 -
Qmax Test Technologies Pvt. Ltd.
CW 409 –Circuit Wizard PCB Test System has all the features of QT9627 such as Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test.Maximum Digital Test Speed 10MHz in the QT9627 .It can be connected to any PC/AT or Laptop with Windows 10 operating system through USB Plug and play interface. It operates on user friendly Qmax Test Director software platform with different modes like Test Station for operator level use Test Sequencer mode for Programmer level use and Interactive Workstation mode for quick working.
-
UTP 6010 RF -
NOFFZ Computer Technik GmbH
The UTP 6010 is one of our smallest test systems and therefore a cost-effective entry into our UTP tester series.The fast system is used to implement scalable functional test applications for a test item (single device under test) with multiple RF channels and mixed-signal test options. Depending on the adapter, the DUT can be tested at circuit board level (FKT) or when installed at the end of the line (EOL).Depending on the test item requirements, we configure the appropriate number of channels and integrate the necessary interfaces directly in the adapter or tester. The test speed, production volume and overall complexity of the UTP 6010 interfaces can be varied according to your requirements.
