Showing results: 256 - 270 of 851 items found.
-
Vacuum Interrupters, Inc.
Until now, the accepted field service test for vacuum interrupters has been a simple Go/No-Go test performed with an AC high potential test. Today, testing with our Magnetic Atmospheric Condition (MAC) test sets can prevent unnecessary damage to your circuit breakers and contactors by predicting the usable life of the vacuum interrupter.
-
1928 -
Peaceful Thriving Enterprise Co Ltd
*Handy pocket clip.*Bright neon indicator.*With UL and cUL Approval.*Insulated housing and test leads.*Check voltage on 90-300V AC/DC.*Built-in lamp will glow if the circuit is live.
-
EverythingPCB
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
69127 -
Klein Tools, Inc.
Device for checking live 6-24V, AC or DC circuits.Tests for shorts in automotive and truck electrical systems, motor field coils, radio and low-voltage circuits, ground circuit of all lamps, wiring, fuses, etc.Bulb in handle glows when circuit is complete (bulb included).Pointed 3-3/4'' (95 mm) probe makes checking easier.Deluxe 3.5'' (89 mm) long handle with nylon top holds replaceable bulb.36'' (914 mm) test lead with alligator clip.Replacement bulb: Cat. No. 69130
-
Extech LCR203 -
Extech Instruments Corporation
The LCR203 are SMD component tweezers for use with Extech's LCR200 LCR meter. These tweezers make it easy to test and sort simultaneously for single handed operation. Tweezers complete the circuit with components easier than separate test leads. Comes with a 6 month warranty.
-
Circuit Check, Inc.
Flash programming stations allow you to offload flash programming from functional test systems, increasing test throughput while improving capital utilization. Circuit Check flash programmer fixtures support multiple programmer types and multiple I/O configurations.
-
TA-400 -
Tech-Aid Products
A Universal ADI Test Panel built to test one of the Astronautics indicators. Panel includes meter drive capability and a specific synchro auto-rate transmitter circuit that allows rates of up to 355 deg/sec. The standard ARINC capabilities make this a universal type tester.
-
Qmax Test Technologies Pvt. Ltd.
Boundary Scan Trainer Kit was developed by Qmax to provide user a good understanding and hands on the testing principals of boundary scan namely the scan chain test, interconnect test, non-BS functional testing of logic IC and cluster like a combinational or sequential circuits.
-
HIGHVOLT Prüftechnik Dresden GmbH
High current test systems are used to test the thermal stability of equipment and components. The test system induces a current in the test object causing it to heat up. Therefore, the test object is designed as a shorted circuit. The high current test system measures the temperature of the test object at various points, in addition to the current. As a special feature, the temperature that the test object should reach can be specified and the amount of the current can be automatically calculated by the HIGHVOLT test system.
-
Circuit Check, Inc.
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.Today’s fifth generation Pneumatic drive supports as many as 8,000 test probes with centerline spacing to 25mil, and contacting test pads as small as 0.014″.
-
Q1 Test, Inc.
In-circuit-testing (ICT) is usually used on mature products, especially in subcontract manufacturing. It uses a bed-of-nails test fixture to connect with multiple test points on the PCB’s bottom side. With sufficient access points, ICT can transmit test signals into and out of PCBs at high speed to apply evaluation of components and circuits.
-
DiagnoSYS Systems Ltd
The compact and portable Faultfinder VIP system, combined with a Laptop running TestVue software, provides a way to rapidly identify failures by troubleshooting a PCB or CCA. It uses impedance signatures (also known as VI testing) measured from a known working circuit and stores them as a test program. These stored signatures are then compared to the ones being measured on the suspect circuit to automatically determine if there is a fault.
-
Tripp Lite
Tripp Lite's Multi-Functional Network Cable Tester allows you to test wiring continuity for Cat5, Cat6, Phone and Coax cable assemblies. Identifies mis-wires, short circuits and open circuits. Features two piece transmitter and receiver, two BNC-F coax converters and coax terminator. Includes handy storage pouch when not in use. Power supplied by 9V Battery (not included).
-
NEO TELE-TRONIX PVT. LTD
These durable and modern Test Sets For Switchgear Industries are developed for determining the tripping of circuit in emergency or random current fluctuation. These testing systems save the outage and break-down of any electrical systems. They are designed to be used on multiple types of circuits. From voltage, current to vacuum, every factor is precisely tested to provide accurate results. They are easy to use and install sets available with user-friendly features.
-
EM-6980 | 20 Hz – 50 KHz -
Electro-Metrics Corp.
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.