-
product
Portable Bar Code Verifier
Inspector Model D4000 CR2 Scanner
The Model D4000 CR2 Scanner provide a Point-and-Shoot Traditional Method that also includes the ISO 15416 and ANSI X3.182 Decodability parameter grade. This unique portable bar code verifier can interface with either the patented RJS Auto-Optic scan head or a CR2 scanner (either in a single piece or connected with a cable). Store and print capability, multiple scan averaging and subsymbology choices are easily accessed through a simple four-button user interface. The scanners are easily installed by the user, which makes the unit quickly adaptable to practically any verification requirement.
-
product
Photonic Components
Fraunhofer Institute for Telecommunications
The Department of Photonic Components is researching optochips and Photonic Integrated Circuits (PICs) for transmission and reception of more than 100 Gbit / s and the sensors. The department provides production and development services for all activitiesfor the German and international industry. If, for example, you already think of a particular optochip concept, the researchers offer additional advice and take over design and production steps. On the other hand, if you would like to start with...show more -
product
User-Serviceable Photometers
8177
TSI''s Automated Filter Tester Models 8127 and 8130 have been used for respiratory filter and filter media testing by leading regulatory authorities and hundreds of manufacturers for over 20 years. These testers are 42 CFR 84, EN 143, ISO 23328-1 & GB2626 compliant. Cleaning the photometers in these testers used to require sending the assembly to the factory for service.
-
product
CAN FD/CXPI Communications Expansion Kit
OP-SB87FD
OP-SB87FD is an expansion board for LE-8200A/LE-8200 used for monitor/simulation of CAN (ISO 11898-1), CAN FD (ISO11898-1:2015), and CXPI (JASO D015). With this kit and the line state sheet, LE-8200A/LE-8200 works as a stand-alone type analzyer for CAN, CAN FD, and CXPI. The board supports development of CAN (used for automotive industry and other industries), CAN FD (next-generation standard of CAN providing more high-speed and communication capacity), and CXPI (invented in Japan to replace direct wirings) devices.
-
product
System
SYS-24
The system shown here was built for a customer to be used in metallization, a common use for many smaller systems. It is also fully capable of performing optical coatings when equipped to do so. This particular system came equipped with a 16" APD ISO Flange mounted cyropump, and a Varian tri-scroll for roughing. The cooling tubes for the crystals as well as the drive motor for the parts holder can be seen on the top of the chamber.
-
product
Max-Hand Durometer
Model 3000
The Max-Hand 3000 durometer is Rex Gauge Co.'s latest innovation for the testing of specimens with creep. The Max-Hand 3000 has a max- hand and an active hand for observing the creep characteristics of a specimen. What makes the Model 3000 unique is the magnetic-drag maximum reset mechanism. Available ASTM, DIN, ISO Types: A, D.
-
product
Wrap Reel
TESTEX Testing Equipment Systems Ltd.
Wrap Reel, to produce skeins of yarn of a pre-determined length and number of turns for count and strength testing. Yarn Length Measuring Device complies with ISO 2060, ASTM D1907/2260, BS 2010, etc. Wrap reel yarn testing will be more accurate if you use our Wrap Reel.
-
product
Eurostat Turnstiles
For companies who need to ensure that the operators cannot enter the EPA unless their wrist straps and footwear are compliant every day• The turnstiles comply with ANSI/ESD S20/20 specification and ISO standards record keeping requirements • Both ESD safe shoes are tested separately through measuring electrodes, installed in the contact mat.• This system tests operators quickly (≤ 3 sec) and automatically and generate reports for the ESD coordinator• Communication with a server for traceability ...show more -
product
6″ (15.25 cm) 1000W Pre-Irradiation Solar Simulator
Model LS1000-6S-009
1000W Pre-Irradiation Solar Simulator Kit specifically designed for the pre-irradiation step during in vitro broad spectrum sunscreen testing. Fully compliant with the most current FDA and ISO requirements. The 6″ (15.25 cm) Class A beam can irradiate up to 9 PMMA plates simultaneously.
-
product
Weather-Ometer/ Fade-Ometer
Ci3000+
Atlas Material Testing Solutions
The Ci3000+ Weather-Ometer and Fade-Ometer with their advanced digital control systems, represent monumental achievements in applying digital and optical technologies in easy-to-use laboratory weathering instruments. The 3000 Series is approved by many OEMs in the textiles, paints & coatings and plastics industries as the exclusive platform to deliver accurate, reproducible and repeatable results for predicting service life. The 3000 Series has been certified CE, UL, CSA, ISO and EN compliant.
-
product
Safety Command Devices
Leuze electronic GmbH + Co. KG
For stopping in emergencies, EN ISO 12100‑1 stipulates protective devices and supplementary measures such as E‑Stop buttons or emergency rope switches. The E‑Stop buttons are used wherever it makes sense to be able to enter a stop command at a specific location. E-Stop rope switches are used for larger danger zones.
-
product
Online Sulfur Analyzer
SOLA iQ
The SOLA iQ On-line Sulfur Analyzer replaces expensive and time consuming laboratory sampling for measuring total sulfur in refinery products including gasoline, diesel, kerosene, and jet fuel as well as many process gas samples such as Natural Gas, NGL and SynGas. The SOLA iQ analyzer offers an online adaption of ASTM D5453, D6313, D6222 & ISO 20846.
-
product
LCF3 Software
Provides system control, data acquisition, real-time graphs, calculation of results, storage of data to disk, and post test graphs and reports in accordance with the relevant sections of ASTM E606-04, BS 7270 (2006), and ISO 12106 (2003).
-
product
Smart Card Testers
CT1000
The CT1000 testers are open and configurable to test any kind of communication protocols used on smart cards, and to be updated for new technologies. The systems can test devices that use common standard protocols (as ISO 18000, EPC Global Gen 2, ISO 14443, ISO 15693, MIFARE™, DESFIRE™, FeliCa™, ISO 11784/85, ICode™, Hitag™, ISO 7816, ISO 7813), and are ready to test also the next generation of cards protocols, such as: USB-Keys, MMC, Micro-SD (with and without CPU inside), M-SIM, HD-SIM, SIM-WAVE, and I2C.
-
product
In Situ Testing Machine
IST Series
Jinan Testing Equipment IE Corporation
*Load meets or exceeds the following standards: ASTM E4, ISO7500-1, EN 10002-2, BS1610, DIN 51221. *Strain measurement meets or exceeds the following standards: ASTM E83, ISO 9513, BS 3846, EN 10002-4. *Safety: This machine shall conform to all relevant European CE Health and Safety Directives EN 50081-1, 580081-1, 73/23/EEC, EN 61010-1.
-
product
Couplers & Power Dividers
*High power handling 750W Ultra-broadband devices support from 555 to 3800 MHz*Very low PIM <-160 dBc with low insertion loss*Outdoor rated unit with support for 7-16 and 4.3-10 connectors*Designed and produced to ISO 9001:2008 centrfication standards for reliability and quality
-
product
Build to Print Services
Whether you need a single system or 100 identical systems or products, WinSoft has the engineering and production expertise, advanced facilities, proven processes, and ISO 9001:2008 quality management system to deliver the highest quality products and services to you. All of our products are developed, manufactured and assembled in the USA.
-
product
Automatic Extensometer
SIE-560A/560SA
To determine the suitability of a material for an application where it is under load, measuring its elongation is important. Measuring elongation enables determination of the elastic modulus (reversible elongation in the elastic region) by measuring the small initial elongation range, and determination of elongation at specimen failure, by measuring larger irreversible elongation in the plastic region. Shimadzu’s SIE-560A series automatic extensometers accomplish both of these measurements with ...show more -
product
Systems for Vibration Monitoring and Diagnostics
*Reliable permanent vibration monitoring according to DIN ISO 10816*Cost effective real-time vibration monitoring for machine protection*Increase availability and reliability, reduce maintenance costs and ensure quality*Compact field units and modular control cabinet systems*Analog output and switching output for alarm function
-
product
Block Ovens
These safe, accurate ovens perform long-term high-temperature air or oil aging tests to ASTM, ISO and government standards.
-
product
Human Vibration Measurement
Metra Mess- und Frequenztechnik in Radebeul e.K.
For hand-arm vibration measurement according to ISO5349 and ISO / TR 18570, whole-body vibration measurement according to ISO2631 and ship vibrations according to ISO 20283-5 Measurement ranges for acceleration, speed and distance for measuring machine vibrations
-
product
HV Enclosures with Integrated Safety Test
The HV test hood according to Performance Level e (ISO 13849-1), developed by us according to the EN50191 standard (erection and operation of fixed and temporary electrical test installations), offers the highest safety for the operator. The large test chamber is enclosed with a hood made of sturdy, highly insulating and transparent plastic. During the test, there is a clear view of the test specimen. A signal light visually indicates safe opening when the light is “green”. “Red light” symbolise...show more -
product
Transistor-Level Defect Simulator
Tessent DefectSim
Tessent DefectSim is a transistor-level defect simulator for analog, mixed-signal (AMS), and non-scan digital circuits. It measures defect coverage and defect tolerance. Tessent DefectSim is perfect for both high-volume and high-reliability ICs. Tessent DefectSim replaces manual test coverage assessment in AMS circuits needed to meet quality standards such as ISO 26262 and provides objective data to guide improvements in DFT. Tessent DefectSim dramatically reduces SPICE simulation time compared to simulating every potential defect.
-
product
Calibration Wheel
A torque analyzer or a torque sensor are a finely tuned instrument designed for testing and monitoring torque applications. In order to maintain accuracy, it is crucial that torque measuring equipment be properly calibrated regularly. Calibration wheel is engineered for calibrating torque analyzers and sensors and ensuring instruments are traceable to National or International Standards, such as N.I.S.T and ISO.
-
product
RFID
HF (13.56 MHz)
BIS M uses the high frequency (HF) 13.56 MHz and supports the standard according to DIN ISO 15693 and 14443. Communication modules/gateways are used for the point-to-point or bus linking and are directly connected to a serial interface of a PC/a bus interface. The Subnet16 TM bus architecture supports a subnet of up to sixteen nodes via an RS485 interface.
-
product
Limit Switches
With its choice of casings, wide range of actuators, variety of connections and high degree of resistance to impact and splashes, Crouzet Switches offers limit switches available in the following ranges: Metal body, Plastic body, Special products and Products for severe environments. Their main characteristics are: IP6x seal, a wide range of actuators (plungers and rollers), rotary heads with momentary action, positive break contacts, compact size, etc. They also offer the option of having special levers, prewiring, connection via ISO cable glands, etc.
-
product
Washing Fastness Tester
TF418A/B/C/D/E
TESTEX Testing Equipment Systems Ltd.
Washing Fastness Tester, to determine color fastness to washing or dry cleaning to ISO, BSI, AATCC and Marks & Spencers standards.
-
product
Rubber Process Analyzers
RPA
Virtually every aspect of a rubber material’s processing and performance characteristics is influenced by its rheological properties. TA Instruments provides a complete range of rotorless shear rheometers and curemeters to help you optimize processing, curing, and application performance. All TA Instruments rubber rheometers are manufactured to exacting mechanical standards and with the latest measurement technology for the most accurate, reliable, and reproducible data available. Available auto...show more -
product
Stainless Steel High Performance Flow Sensor
2540
The Signet 2540 Paddlewheel Flow Sensor offers field-replaceable electronics and transient voltage suppression (TVS) to provide greater immunity to large voltage disturbances (i.e. lightning) sometimes encountered in field wiring. Sensors can be installed in DN40 to DN600 (1 to 24 in.) pipes using the 1 inch NPT or ISO 7/1-R 1.5 threaded process connection. The sensors are also offered in a hot-tap configuration with a bleed valve service without process shutdown in pipes up to DN900 (36 in.). Both styles of sensors must be used in full pipes and can be used in low pressure systems.
-
product
Elemental Analyzers
Bruker manufactures instruments for elemental analysis from 100% down to the sub-ppb trace level. Easy-to-use solution packages help customers in process and quality control to meet industry norms and standards including ASTM, DIN, ISO and FDA. Highest analytical accuracy and precision enable academic research from lab to field.
