Showing results: 661 - 675 of 1151 items found.
-
DT4 -
North Atlantic Industries
The DT4 module (the enhanced version) features 24 programmable channels for either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3 – 60 VCC source. These modules can sense broken input connections and whether an input is shorted to +VCC or to ground. Additional features of the DT4 (Enhanced Version) are listed below.
-
Ranger® R3D -
Teledyne FLIR
The Ranger R3D is a dual mode, ground surveillance radar designed to provide efficient, 24/7 persistent surveillance, both within and beyond the fence. Operating in the Ka-band, the Ranger R3D leverages the resolution and accuracy of advanced FMCW technology and the extended range and terrain adaptability of Doppler in a single, compact, and lightweight package. Ruggedized for permanent, all-weather installations and mobile, stop-and-scan operations, its low minimum detection velocity (MDV) detects slow-moving threats such as walkers and crawlers.
-
MEET International Ltd.
*Detects AC voltage by non-contact method: 70VAC to 250VAC*Finds broken wire location*Wrong connection check*Ground / Earthing disconnection check*Detects static radiation of TV / monitor*Checks operating condition of ionizer*Microwave leakage detection: ≥5mw/cm2
-
298 -
SCI
Our Model 298 is a simple-to-use 500VA AC Hipot Tester with the built-in ability to test Ground Continuity (Low Current Continuity). The 298 500VA AC Hipot Tester includes all the features you need to get the job done and move on.
-
DARE Electronics
DC voltage sensors monitor input voltages ranging from 3 to 500 volts DC with a trip point accuracy of up to 1% in airborne, military and ground power applications. Using internal electronic circuits to detect, monitor and/or sense DC voltage, DARE DC voltage sensors, monitors, and voltage sensing relays can open or close a circuit when a certain pre-set over or under voltage condition exists or the DC voltage falls outside the specified voltage band window.
-
Tektronix, Inc.
A low voltage single-ended probe is typically used for measuring high-speed, ground referenced signals up to 12 V. These low voltage probes are the best choice for making measurements on high impedance, high frequency circuit elements which require minimal probe loading. Users should select probes with a low input capacitance specification (~1 pF) to minimize the probe’s loading effect on the circuit. A probe with lower input capacitance will offer higher input impedance at higher frequencies.
-
Alliance Support Partners, Inc.
An increasing number of electronics products are being assembled in panels of 8 or more to minimize production cost. These products are typically tested with in-circuit tests (ICT) followed by power-on functional tests. Normally, ICT requires isolation of power and ground while measurements are being performed. Functional tests, including in-system programming (ISP), require board power to be applied. The Modular Relay Board (MRB) is designed to switch power onto each individual board and to disconnect sensitive signals during functional test.
-
Minder -
Mindarray Systems, Inc.
Minder is an IT performance management suite for businesses and organizations to monitor and analyze performance across multiple applications and network resources. Minder helps you take control of your dynamic IT infrastructure by cross-domain monitoring, multiple product support, SLAs, forecast analytics and other impressive features. Driven by innovation, Minder is built from the ground up to provide next generation IT management. Minder is cost effective management solution can be deployed in less than hour and are designed to avoid dependence on any server host.
-
VXI-5502 -
ICS Electronics
* VXI-5502 has a Sea-of-holes Prototyping Board with multiple power and ground planes for analog and digital prototyping applications.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
PCE Instruments
At PCE Instruments you will find three types of radioactivity meters: Alpha radioactivity meter, meter for Alpha, Beta and Gamma radioactivity, radioactivity meter for human beings. It is very important to measure radioactivity as well as to classify radioactivity values. An example of Gamma radioactivity: Terrestrial gamma radiation is measured according to general values from 0,03 – 0,3 µSv / h (micro Sievert/ hour). This "normal“ oscillation range is conditioned by contents in the ground of natural radioactive elements such as uranium, potassium, etc.
-
WL MIDGET -
Walter G. Legge Company Inc.
WL MIDGET Surface Resistance Meter is an ultra-wide range, battery operated, portable instrument for measuring Surface Resistivity and Resistance to Ground of virtually any flat surface conforming to ASTM D-257 standard method by using recommended parallel bar sensing probe. Gives simple, repeatable measurements of conductive, static dissipative, and insulative surfaces. Ranging is automatic due to the use of high-speed OP-AMP Integrated circuits being linear, with changeover points +1/2 decade on a logarithmic scale. Repeatability equals + 5%.
-
KHZ43201 -
Beijing KeHuan Century EMC Technology Co,.LTD
The KHZ43201 voltage probe is a standard low resistance test probe, which meets the technical requirements for this product in the CISPR16-1 and CISPR14-1 test equipment. When measuring the interference voltage of the power grid, the artificial power supply network cannot be used at the load port, and sometimes it is necessary to use a voltage probe to measure the interference of the signal port, the load port, and the antenna port. The input impedance of the voltage probe to the ground wire is greater than 1.5KΩ, which can protect the input terminal of the receiver.
-
TE Connectivity Ltd.
In-Building Distributed Antenna System (DAS or i-DAS) antennas are low profile and designed to be mounted discreetly to a hard or tiled ceiling. Used in a series throughout large buildings, campus areas or even in below ground sections of a building the antennas can provide a distributed LTE or Wi-Fi signal to where it is required most. With a growing demand for in-building connectivity and higher data rates, larger smart or connected buildings require a series of antennas in order to distribute signal around the building or campus area.
-
Improved Shadow® Tactical Unmanned Aircraft Systems -
Textron Systems
With more than 30 years of unmanned aircraft systems (UAS) experience, Textron Systems' Shadow® is the most reliable and capable tactical UAS to help you accomplish your missions. The battle-proven system has surpassed 1.25M hours in flight, supporting global military operations for countless U.S. troops and their allies. Our multi-mission systems are paired with Textron Systems' interoperable Universal Ground Control Station (UGCS) and remote products for collaboration across the battle space.
-
CR MAGNETICS, INC.
CR Magnetics supplies an extensive line of toroidal current transformers for any need. Our offerings include measuring from 10,000 amps to a few milliamps. This includes ANSI, Commercial, Ground Fault, High Frequency, Wound Primary, DC Immune and Nano Alloy current transformers. Various outputs include 5 amp secondary, high turns ratio voltage outputs for both wire leads and pcb configurations. Our products are UL Recognized for both US and Canada.
