Filter Results By:

Products

Applications

Manufacturers

Gigahertz

one billion Hz. AKA: GHz

See Also: Frequency, Microwave, Terahertz, GHz, 5G


Showing results: 766 - 780 of 2543 items found.

  • Micro probes 1 MHz up to 1 GHz

    MFA 02 set - Langer EMV-Technik GmbH

    The two in the set included micro probes are used to measure low-frequency magnetic fields up to 1 GHz, e.g. at signal conductors (150µm), SMD componets (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the BT 706 Bias tee. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee to a spectrum analyzer or an oscilloscope. The MFA 02 set delivery of Langer EMV-Technik GmbH includes correction lines. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.

  • Wideband GaN Amplifiers

    Teledyne RF & Microwave

    The Teledyne RF & Microwave family of GaN-based amplifiers maximizes power density and efficiency, and establishes a new benchmark for small size in the 0.1 to 6.0 GHz range that operates over multi octave. With dimensions of 2.5"L x 2"W x 0.42"H at only 2.1 cubic inches, these modular, non-ITAR GaN amplifiers maintain the rugged design characteristics needed for harsh airborne and land based requirements.

  • Amplifiers

    Teledyne RF & Microwave

    We have designed and manufactured amplifiers using all major semiconductor materials, LDMOS, GaN, GaAs, and InP, to produce narrow, wideband, and pulse, receive and transmit amplifiers from 1 MHz to 220 GHz and power levels from mW to over 10 kW.

  • 2 To 18 GHz 6 Channel Downconverter

    Teledyne RF & Microwave

    Teledyne RF & Micrrowave's Six Channel 2 - 18 GHz (RF and LO) downconverter operates with an IF of ~960 MHz, providing 25 dB of RF-IF gain, and bandwidth of ~500 MHz. This downconverter operates on a single LO at -6 dBm which is amplified, split, then again amplified to each of the 6 channels. Integrated into each channel is a range extension switch, controlled by a TTL input and adding 20 dB attenuation. Noise figure is ~ 13.5 dB and output IP3 is ~+25 dBm. The downconverter is 2- sided, hermetically sealed and designed for rugged applications.

  • 17 To 19 GHz QPSK Modulator

    CCM19001 - Teledyne RF & Microwave

    The CCM19001 is a Differential Drive Digital QPSK (Quadrature Phase Shift Keying) modulator operating across the 17.0 to 19.0 GHz frequency range. The modulator utilizes differential drive digital inputs (180º apart) to drive both of the bi-phase modulators (mixers) integrated into the assembly. The modulator is a combination of a matched pair bi-phase modulators, which are in quadrature (90º) to each other. It is modulated by switching polarities of the DC voltage controls in 4 different logic states ("0,0", "0,1", "1,0" & "1,1") for 4 phase states. The QPSK modulator provides constant amplitude, 90º vector: 0 (ref.), 90º, 180º, 270º and operates across the -55º to 85º C temperature range.

  • Low Noise Dual Band VCO

    Teledyne RF & Microwave

    This custom oscillator subassembly consists of two low noise oscillators covering 1.5 to 2.5 GHz, a power combiner, a standard Teledyne RF & Microwave amplifier, and a lowpass microstrip filter. Teledyne RF & Microwave designed both oscillators for low phase noise and linear tuning. The output frequency bands are switched using standard TTL control.

  • TINYig Oscillators

    Teledyne RF & Microwave

    The smallest available oscillator in the industry, Teledyne Microwave's TINYIG is an ultra-low phase noise YIG-tuned oscillator (YTO) that provides superior phase noise frequency up to 20 GHz. Uniquely designed to be RoHS compliant, these YIG TO-8 oscillators exploit the principle of magnetic resonance to generate a clean, low phase noise microwave signal over broad tuning ranges. It can greatly simplify system designs, thus reducing costs, eliminating the need for extra components, and reducing the risk of malfunctions of complicated electronic connections and operations.

  • X Band Coupler With Dual Output Threshold Detector

    Teledyne RF & Microwave

    The X Band coupler with dual output has an input power range of either -5 to +10 dBm, or +5 to +20 dBm. Covering 8.0 to 9.5 GHz, insertion loss is less than 1.0 dB and VSWR is 1.5:1. The coupler/detector has two external resistors providing independently settable threshold TTL outputs. The power flatness is ~0.4 dB and hysteresis is 0.1 dB. Cougar can provide this function in other frequency ranges and input power ranges.

  • Ku Band Gain Control Amplifier

    Teledyne RF & Microwave

    Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.

  • IQ Networks

    Teledyne RF & Microwave

    Teledyne Microwave Solutions (TMS) offer a capable range of high performance IQ Modulators and Image Reject Mixers as well as IQ (Quadraphase) Modulators which can be used on applications from commercial test equipment to space qualified projects. IQM products can be used either as an IQ modulator or IQ demodulator and cover several frequency bands from 1.4 GHz to 18 GHz.

  • Low Noise Amplifiers

    Teledyne RF & Microwave

    Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a wide range of applications but are primarily suited to communication systems including both Data-Link and Satellite Communications (Satcom) systems. Our new K-Band LNA operates over a 19.2 - 21.2 GHz with 1.3 dB Noise Figure at 25°C. It is configured with a waveguide input and 2.92 output connector all in a hermetic package.

  • Solid State

    4701 Series - Dow-Key Mircowave Corporation

    The 4701 Model is a Non-blocking Full Fan-Out (any input connected to any output simultaneously) coaxial switching system operating from 1 GHz to 18 GHz. The system is configured with maximum (12) N-type inputs and (12) SMA-type outputs. All inputs are outfitted with high linearity amplifiers in order to compensate for system insertion loss.

  • Fan In/Outs

    Dow-Key Mircowave Corporation

    The 4601 Model is a Non-blocking Full Fan-Out (any input connected to any output simultaneously) coaxial switch system operating from 1 GHz to 18 GHz. The system is configured with maximum (8) N-type inputs and (8) SMA-type outputs. All inputs are outfitted with high linearity amplifiers in order to compensate for system insertion loss.

  • Flip-Flop Electronics

    Analog Devices Inc.

    Analog Devices supplies a range of D type and T type flip flop products. Members of this portfolio can support data transmission rates up to 43 Gbps and clock frequencies as high as 43 GHz. All of our flip flop products are RoHS compliant and available in 3 × 3 or 4 × 4 SMT packages.

  • PIN Limiter Diodes

    Macom Technology Solutions Holdings Inc.

    MACOM’s PIN limiter diodes provide excellent broadband performance from 1 MHz to 20 GHz and higher for receiver protector circuits. Our PIN limiter diodes are available in die form, plastic and ceramic packaging. Our ceramic packaged diode series is ideal for waveguide, coaxial, and surface mount applications, while our die diode series is well suited for chip and wire high frequency microwave applications.

Get Help