Showing results: 796 - 810 of 928 items found.
-
Anchor Test System -
James Instruments Inc.
Two models, each with two different gauge capabilities enable precision readings over a wide range of applications - from light to heavy duty loads. The standard system has a pull stroke of two inches with an option to extend to four inches. The longer pull stroke allows for complete extraction of most fixings in one simple operation. A load diffusion bridge and pyramid are available to keep reaction loads away from the anchor point.
-
PENKO Engineering B.V.
PENKO designs and manufactures a wide range of Amplifiers - also known as digitizers and signal conditioners or PLC weighing cards - which are available as analog or digital versions. These are suitable for use with all types of strain gauge load cells and a number of configurations supplied by PENKO.
-
Q-Card
Test package for combination module adhesion/peel tester includes a motorized test stand, digital force gauge, AC adapter/charger for 115VAC or 230VAC, data acquisition and exporting software, scoring fixture, glue fixture and necessary attachments and cables to perform the above tests.
-
Huaxin instrument (Beijing) Co., Ltd
Here at Huaxin, we offer a selection of HS602 and HX601B intelligent pressure calibrators. They are high pressure, single range digital pressure calibrators with HART communication capability. Composed of high precision measurement chip, 24V DC power supply, battery charging protection circuit, HART communication module and intelligent digital pressure module, these two pressure calibrators provide a pressure calibration solution for gauges, transmitters, and switches over a wide pressure range.
-
SI-1098 -
Smartech Inc.
Coating Thickness Gauge SI 1098 is a highly intelligent and precise instrument used to quickly and accurately measure thickness of coating or plating on almost all kinds of metal surface. Technology – Magnetic Induction – (enables measurement of non magnetic coatings on magnetic substrates such as Steel, Mild Steel, Cast Iron &Magnetic Stainless Steel). Example coatings:- Paint,Zinc / Galvanising, Chrome, Copper, Enamel, Rubber, Paint, Varnish, Powder Coating, Plastic etc.
-
SI-1099 -
Smartech Inc.
Coating Thickness Gauge SI 1099 is a highly intelligent and precise instrument used to quickly and accurately measure thickness of coating or plating on almost all kinds of metal surface. Technology – Magnetic Induction – (enables measurement of non magnetic coatings on magnetic substrates such as Steel, Mild Steel, Cast Iron &Magnetic Stainless Steel). Example coatings:- Paint,Zinc / Galvanising, Chrome, Copper, Enamel, Rubber, Paint, Varnish, Powder Coating, Plastic etc.
-
Advanced Telemetrics International
ATi Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary telemetry receiver. The 2040BC Miniature Strain Gage Transmitter can be connected to strain gauges adhered to propellers or rotors in order to transmit blade strain or shaft torque in flight.
-
Datum Electronics, Ltd.
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
Model 3442RA1 -
Jinan Testing Equipment IE Corporation
With gauge lengths of 1 and 2 inches (25 and 50 mm) and measuring ranges of 0.050 and 0.100 inches (1.2 and 2.5 mm), the Model 3442RA1 was designed for applications where tensile or compressive strength tests on small rock, concrete and other small compression samples is desired.
-
FHM10 -
TSI Inc.
Fume hoods are a primary source or protection in laboratories. Face velocity measurements are often used to gauge the performance of a fume hood’s ability to contain and exhaust hazardous chemicals. By accurately measuring face velocity and alarming on unsafe conditions, TSI’s FHM10 Fume Hood Monitors provide a high level of fume hood safety. And, the FHM10 helps users comply with standards and regulations set forth by OSHA, NFPA, ANSI Z9.5, and SEFA, calling for monitors to be installed on fume hoods.
-
Beamex Oy Ab
We offer pressure calibrators as portable and as workshop models. Pressure measurement is performed with internal and/or external pressure modules for better flexibility. Pressure measurement ranges go from vacuum up to 1000 bar (14,500 Psi). Both gauge (vacuum and positive) and absolute pressure can be measured with same modules meaning you don’t need to buy so many module for greater flexibility. Also, intrinsically safe pressure calibrators are available for use in hazardous areas.
-
WDW-L series -
Jinan Testing Equipment IE Corporation
Electric Vertical Test Stand is a tensile compressive test stand especially designed to match push-pull force gauge. This series pf electric vertical test stand has good stability, wide application range and is convenient to use. The electric vertical test stand has stepless speed-adjusting uniform motion, digital display of the testing speed and converting mode between manual and automatic operation. The vertical test stand is specialized for tension/compression test, insertion/withdraw test, fatigue test and fracture test.
-
Atico Export
Direct indication of impact energy absorbed by specimen on large diameterAvailable with safety guard for the operatorInitial potential energy for Charpy is 300 Joules & for Izod is 170 Joules with a L.C. of 2 Joules (for Analogueodels) & resolution of 0.5 Joules (for Digital Model)Pendulum drop angle for Charpy is 140° & for Izod is 90°ASTM Impact Testing machine is also supplied, which conforms to E-23 ASTM standarAvailable with Gauges, Tongs, Sub-zero bath, Templates, U & V-Notch milling cutter (Optional)
-
Hydraulic Technology, Inc.
Our modular hydrostatic test chambers are designed with open ends to accommodate the connection to similar units for the purpose of lengthening the enclosed test area. The modular test system starts with a base unit with complete pump system, gauges and controls mounted on the 60” x 24” x 18” test chamber. If longer test lengths are required, simply add another test chamber to double, triple or quadruple the test length area. Specify your particular requirements at our Customization Page.
-
CX-15 -
Shenzhen Chuangxin Instruments Co., Ltd.
The Impact Test Ball is a specially machined ball to test impact resistance according to IEC, CSA and UL Standards. It is made of chrome-plated-steel for durability, and is fitted with an eyelet to facilitate testing for pendulum applications. Eyelet is threaded to the ball to allow attachment of a handle or force gauge. Weights are closely controlled.