Showing results: 976 - 990 of 1134 items found.
-
Intego GmbH
Intego's knowhow even makes it possible to identify challenging defects that may be located under the surface. One system is the inspection of chips by means of lock-in thermography, which visually represents the IR radiation intensity signal of electronics. Special lasers and flash lamps generate a very short heat impulse (10 ms) on the chip, which generates a measurable heat flow. In most cases, a resolution of < 1 μm can be achieved.
-
Guangzhou Jumho Electric Co., Ltd.
Cell phones and other wireless devices radiate powerful electromagnetic fields that can cause interference and noise in microphone signals. The interference and noise is called RF interference, which is an unwanted “signal” that occurs at the same time and frequency as a data signal. The RF interference disrupts the flow of data and degrades quality-of-service. Jumho Electric provides a cost-effective RF interference test system for GSM interference level measurement of wireless microphone.
-
Russells Technical Products
Our dynamometer chambers feature dependable mechanical refrigeration, superior air flow, and expansive control systems. Our dynamometer drive-in vehicle test chambers are designed to integrate directly with a dynamometer system, while simultaneously exposing vehicles to a wide variety of environmental conditions including temperature and/or humidity, rain, wind, and more. Our control systems allow for precise temperature and humidity testing while meeting your exact specifications.
-
Cincinnati Sub-Zero Products
CSZ's accelerated stress test chambers combine mechanical refrigeration; LN2 cooling and high velocity air flow for fast product temperature change rates. Chambers are typically designed with a change rate up to 30C (54F) per minute based upon the part temperature. Common uses are production stress testing circuit boards, electronic drives, assemblies, etc. Design allows the user to quickly control and change the temperature of the product.
-
FST -
Fuji Electric Co., Ltd.
Three pairs of sensors for accuracy of ±0.2% of rate. Using the new algorithm for calculating the flow velocity, it can measure any type of fluid with high accuracy. Low maintenance. With no moving parts, FST has long-term stability while requiring only minimal maintenance work. Bubble resistant. By using the advanced anti-bubble measurement technology, the interference from air bubbles is greatly eliminated. Pipe diameter: 50 mm, 80 mm, 100 mm.
-
Hilkar
Iron core Shunt Reactors act as an absorber of reactive power to increase energy efficiency of the power system. Shunt Reactors are used in order to compensate capacitive reactive power generated by long and lightly loaded transmission lines as well as underground cables, thus allowing the flow of more active power through the system and avoiding over voltages. Shunt Reactors can be directly connected to the power line or to a tertiary winding of a three-winding power or distribution transformer.
-
3718-A And 3719-A -
KANOMAX USA, Inc.
Kanomax Remote Particle Sensors with analog output are designed to fit into your existing monitoring system, or they can be used as a stand-alone unit to monitor a critical area when connected to an alarm or controller. With two models available, these 2-channel remote particle sensors are capable of Modbus communication via RS485 interface. 0.1 cfm and 1.0 cfm flow rate models are available, along with flexible 4-20mA analog output with the 1.0 cfm unit (only).
-
Circutor, sa
Solutions for monitoring and recording any value you wish to manage (electricity, water, gas consumption, temperatures, flow rates, pressures, units produced, etc.), either through communications or through pulse logger systems. The control system family contains the LINE solution to create a comprehensive energy management systems (SGEi), LM pulse loggers and MDC controllers to avoid surcharges in the electric bill by preventing the contracted capacity in electrical installations from being exceeded.
-
Chengdu KeyLink Microwave Technology Co., Ltd.
RF Circulators from KeyLink Microwave are passive 3-port microwave devices designed to provide isolation between transmit and receive signals for radar, satellite communication, and telecommunication applications. These microwave circulators can control the signal direction and flow inside an RF circuit. KeyLink provides broadband RF circulators spanning the frequency range of 1 GHz to 18 GHz in varying bandwidths, tailored to cover all standard and popular bands commonly used throughout the market place.
-
Post Glover
The main purpose of a Neutral Grounding Resistor (NGR) is to limit the fault current present in a single line to ground fault. Limiting the possible current that can flow in such an event not only reduces damage to equipment but also helps safeguard personnel in the vicinity. Depending on the design of the resistor, this current value can be either high or low, continuous or of a predetermined duration. The resistor’s designed maximum current allows relays and protection settings to be easily determined and enacted, creating a safe work environment.
-
CS2-TM-Analogue -
Chuan Sheng Electronics Co., Ltd.
The CS2-TM Totalizer controller provide high accuracy measurement, display, control and communication (Modbus RTU mode) of 0~10V/4~20mA from flow meter or mV from Shunt for Amp-Hour.There are two display screen and 3 external control input (DI) in standard and the optional 4 Relay, 1 Analogue, 1 Pulse and RS485 port available. They are also support fantastic control function as like as N, R, C mode for totalizer and batch control.
-
9545-A -
TSI Inc.
The VelociCalc® Air Velocity Meter 9545-A is like having multiple meters for the price of one. This meter simultaneously measures and data logs several ventilation parameters using a single probe with multiple sensors. It measures velocity, temperature and relative humidity; and calculates flow, wet bulb and dew point temperature. Ideal for optimizing HVAC system performance, commissioning, plant maintenance, critical environment certification and duct traverses. The 9545 model has an articulated probe.
-
2678X -
Shenzhen Chuangxin Instruments Co., Ltd.
Ground Earth Resistance Tester verifies the integrity (continuity) of the protective bonding of the equipment (Class I equipment) designed to secure safety through the basic insulation and protective earthing. It is also called earth (ground) bonding test. If the continuity of the protective bonding is confirmed, we can conclude that the equipment has the requirements for preventing electric shock even if the insulation between the primary circuit and the accessible conductive section fails and a fault current flows through the distribution system.
-
FIT550 -
Matco Tools
*Performs running, residual, rail and flow rate pressure tests*Large, easy-to-read 3-1/2" dual-scale gauge reads 0-100psi and 0-700 kPa*Kit includes: 50+ adapters, fittings, 48" hose, pressure relief and fuel discharge hose to test most domestic and foreign fuel injection systems*Also includes quick release couplers and adapters to fit other fuel injection test kits*For use with gas engines only
-
Oxytron 2000 -
Bacharach, Inc.
The Neutronics Oxytron 2000 is a custom-configured instrument designed to automatically control oxygen in process applications. When combined with a properly designed sample conditioning package, the Oxytron 2000 provides reliable measurement and control of oxygen, keeping it at a safe level by controlling the flow of inert gas into the process. Originally developed for one of the country’s largest chemical manufacturers, the Oxytron 2000 has been proven reliable in thousands of installations and can provide control for two independent vessels or processes.