Showing results: 511 - 525 of 686 items found.
-
1000 Series ATE -
Circuit Check, Inc.
The Circuit Check 1000 Series ATE provides a configurable standard platform that can utilize multiple mass interconnect interfaces while providing ease of maintenance and the ability to accept a wide variety of test fixture solutions. With the 1000 Series ATE, test procedures become automatic, with test steps and go/no-go limits easily programmable.
-
King Design Industrial Co., Ltd.
*Complies with IEC 61646, IEC 61215 mechanical load test specification. * Air pressure is adjustable, output range is from 2400pa to 5400pa ±5% . * Maximum measurement range: 220 x 260 cm. * Apparatus structure material:aluminum-extruded. * Fixtures and holders can be customized design for requirement of testing module. * Manual operation is simple; manual maintenance is easy.
-
Buehler
Wilson® hardness testers include a comprehensive range of hardness testers from Rockwell®, Knoop/Vickers, and Brinell to fully automatic production systems. Our hardness testers are complemented by a range of ISO test blocks, accessories, and fixtures. Our calibration laboratory is recognized as the global leader in the production of premium ISO test blocks and indenters.
-
Focus-FX -
Kyoritsu Testsystem Co., Ltd.
This is general function test system. User can change board model easily by replacing a test fixture and changing inspection program. We have variety of measurement instruments such as FX modules which can control commercial instruments. It is possible to add required modules into existing units as they are connected by USB port. User can expand as per desired inspection specification.
-
GRS500 -
Polar Instruments Inc
Designed to help troubleshoot complex boards when fixture based tools are not a viable solution, the GRS500 is designed to help you compare the characteristics of good and faulty PCBs, using nodal impedance test, and a "Videosection" technique which presents you with high resolution images of a good board for use in live video comparison with the board under test,
-
F9 Systems, Inc.
The CalBlade backplane calibration fixture isdesigned to permit accurate and convenient impedance and transmission measurements of a HM-Zd backplane. The CalBlade is used to calibratethe logic card connector interface to the backplane rather than to the usual far-end of the coaxial measurement cables. Very accurate impedance, skew and propagation delay measurements are possible since parasitic fixturing effects are removed.
-
Terotest Systems Ltd.
In-circuit test works by checking all components are fitted correctly to the PCB and are within the correct electrical tolerance. In-circuit testers do this by interfacing to the board via a "bed of nails test fixture" and programs can be generated via CAD data. They offer a quick and easy method of checking the manufacture of the board and also offer a reliable and simple fault report.
-
YAVHF3X4C50 -
6TL Engineering
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced! This module features three multiplexers in cascade configuration, for frequencies up to 2,5GHz. In/out is through SMB connectors, selectable for 75 and 50 Ohm. There’s direct control of the relays (24Vdc) or integrating CAN bus interface.
-
YAVHF3X4C -
6TL Engineering
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced! This module features three multiplexers in cascade configuration, for frequencies up to 2,5GHz. In/out is through SMB connectors, selectable for 75 and 50 Ohm. There’s direct control of the relays (24Vdc) or integrating CAN bus interface.
-
YAVHF3X4 -
6TL Engineering
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced! This module features three multiplexers in cascade configuration, for frequencies up to 2,5GHz. In/out is through SMB connectors, selectable for 75 and 50 Ohm. There’s direct control of the relays (24Vdc) or integrating CAN bus interface.
-
N1425B -
Keysight Technologies
The N1425B is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425B is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425B enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425B to the B2985B/87B.
-
N1425A -
Keysight Technologies
The N1425A is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425A is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425A enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425A to the B2985B/87B.
-
FDCS -
Mesuro Ltd
Beyond traditional Noise and Harmonic Load/Source Pull, FDCS also supports Tuner and Fixture (TRL) calibrations, Time Domain Load Line acquisition, Pulsed IV and Load Pull and Active feedback Power Injection operations (for Γ ≥ 1).The measured data are processed graphically into 2D and 3D plots and are converted into popular simulator formats (ADS, AWR etc.).The FDCS user unterface includes many many improvements and optimizations to make load pull and noise measurement easier.The software has ActiveX control for controlling MPT tuners in any ActiveX compatible platform.
-
Focus Microwaves
Beyond traditional Noise and Harmonic Load/Source Pull, FDCS also supports Tuner and Fixture (TRL) calibrations, Time Domain Load Line acquisition, Pulsed IV and Load Pull and Active feedback Power Injection operations (for Γ ≥ 1).The measured data are processed graphically into 2D and 3D plots and are converted into popular simulator formats (ADS, AWR etc.).The FDCS user unterface includes many many improvements and optimizations to make load pull and noise measurement easier.The software has ActiveX control for controlling MPT tuners in any ActiveX compatible platform.
-
95TM -
Com-Ten Industries
The ComTouch controller reports current reading, force results, test stand direction, limit switch warnings, test stand speed, and error messages. Designed to be rugged, sturdy, and easy-to-use, this test stand is built to last. Just select from our wide line of fixtures for standard tensile testing or install an optional compression cage for testing in compression.