Showing results: 31 - 45 of 159 items found.
-
NI
As vehicles advance towards autonomous operation, test engineers face drastically increasing system complexity while dealing with ever present cost and time pressure.
-
Precision Acoustics LTD
The best instrument available to measure close to the face of the ultrasound transducer, make CW measurements or to measure the acoustic pressure and associated thermal effects of a high-intensity field.
-
Qualitest International Inc.
The Package Drop Tester - PDT-II Series simulates the drop/fall of the packaged finished products to evaluate their damages. All the rhombohedrons, angles and faces of the package container can be tested. so that the manufacturer can know how to take measures effectively to protect Its products against damage during transportation. During dropping, the carrier will rotate to allow the packed products to fall freely.lt can test the faces, edges and corners of the product, with small vibration, and stable and reliable operation.
-
WL-D200S -
SYOPTEK INTERNATIONAL LIMITED
The WL-D200 fiber microscopes provide dual-illumination, both coaxial and oblique, to produce the highest-quality image detail and superior view of fiber end face cleanliness and core condition.
-
510108115 -
Virginia Panel Corporation
The 19- position mini power modules are made from G10 Epoxy Glass and can withstand temperatures up to 140 °C. The faces of the power modules are screened red.
-
5250998-84 -
VECTOR Electronics and Technology, Inc.
Fits onto rear face of rear extrusion rails, in between backplaneand extrusion rail to isolate backplane from extrusion.HP pitch pattern of holes for precise installation of backplane.
-
-
FHM10 -
TSI Inc.
Fume hoods are a primary source or protection in laboratories. Face velocity measurements are often used to gauge the performance of a fume hood’s ability to contain and exhaust hazardous chemicals. By accurately measuring face velocity and alarming on unsafe conditions, TSI’s FHM10 Fume Hood Monitors provide a high level of fume hood safety. And, the FHM10 helps users comply with standards and regulations set forth by OSHA, NFPA, ANSI Z9.5, and SEFA, calling for monitors to be installed on fume hoods.
-
FastNetMon
Large volumetric-based DDoS attacks are increasing in terms of frequency and scale at which they are perpetrated. With hundreds of-gigabits worth of attacks becoming commonplace, organizations not only face service interruptions for customers but the complete implosion of their infrastructure’s operation. In the face of this increasingly challenging threat landscape, BGP FlowSpec DDoS mitigation has emerged as one of the most effective techniques to mitigate DDoS attacks. Combined with an accurate and speedy detection system, it helps manage and synchronize working with firewalls to mitigate these attacks.
-
510104123 -
Virginia Panel Corporation
The 19-Position Mini Power modules are made from G10 Epoxy glass and can withstand temperatures up to 140 °C. The face of VPC power modules are screened red and the nomenclature in white.
-
ADS EVO -
HORIBA, Ltd.
Vehicle developers face increasing pressure to reduce development times, while vehicle complexity is increasing. The ADS EVO ensures accurate and repeatable global test cycles on chassis dynamometers.
-
6700BH Series -
Nihon Denji Sokki Co., Ltd
This BH curve tracer is adopted pole coil measuring method. The limit of size and shape for measuring work is very little and it can measure the difference of both face and reverse side of magnet.
-
BroadSim Solo -
Safran Federal Systems
Designed to address the permanent challenges that engineers face with laboratory capacity and availability, BroadSim Solo was developed to bring advanced GNSS scenario creation to your desk and propel development cycles.
-
Shimadzu Corp.
This jig is designed for tensile testing optical fibers and other brittle fibers. The jig consists of upper and lower pneumatic flat grips with flat grip faces followed by large-diameter capstans.
-
EUROSMC, S.A.
The IEC 61850 represents the migration from the analog to the digital world to the substations. Accordingly, industry faces a period of transition, also noticing the effects of IEC 61850 in the traditional checking and monitoring procedures.