Showing results: 1 - 15 of 21 items found.
-
TR-AS FRA -
Dr. Strauss Messtechnik GmbH
The Frequency Response Analysis (FRA) on power transformers is used for diagnosis at works, after putting into operation and for maintenance on site. The frequency dependent admittance is determined and recorded as fingerprint.
-
-
CAPture FRA -
Captronic Systems Pvt Ltd
A Frequency Response Analyzer (FRA) is a high precision measurement instrument used to analyse dynamic behavior of circuits & components of control systems in the frequency domain. An FRA generates a sinusoidal signal and inserted it into a unit under test. This signal is measured at the point of insertion using one of the input channels on the FRA The inserted signal travels through the UUT and the same signal is measured simultaneously by the FRA at other input channel. The technique measures the magnitude and phase relationship between output and input waveform as a function of frequency.
-
Ametek Scientific Instruments
Simultaneous Electrochemical Impedance Spectroscopy (EIS) tests can be run on multiple cells by connecting Solartron 1455A/1451A series frequency response analyzer (FRA) modules to the 1470E. These FRAs can operate in single sine correlation or multi-sine / Fast Fourier Transform (FFT) analysis mode, providing the ultimate in speed, precision and accuracy. The 1455A FRA provides high performance impedance measurements over the frequency range 10 μHz to 1 MHz, while the 1451A FRA operates from 10 μHz to 100 kHz.
-
Wabtec
Wabtec M Series Recorders provide a compact recording solution for discrete electrical and pneumatic signals and provide compliance to FRA Crash Hardening requirements.
-
1280Z -
Ametek Scientific Instruments
The Solartron Analytical 1280Z Electrochemical Test System is a complete instrument that packages the potentiostat hardware for DC and Frequency Response Analyzer (FRA) hardware for AC tests in a single compact unit.
-
Apps-XM Series -
Ametek Scientific Instruments
This family of instruments is built on the technology of the ModuLab XM platform. Specific combinations of options, such as frequency response analyzers (FRA), current boosters, voltage boosters, are popular when the ModuLab XM is configured for given applications. We combine our design knowledge and industry experience to create a line of products with an application focus.
-
Cleverscope Ltd.
Isolated Signal Generator (0-65MHz, Sine Wave Only) for serial numbers above 4000. The CS701 is rated at 300V RMS isolation (class III), and offers output levels from 1 mVp-p to 7 V p-p. You can use the CS701 for Power Supply FRA without needing an isolation injection transformer.
-
DRA5228/F -
Hangzhou Huatai Optic Tech. Co., Ltd.
Raman Fiber Amplifier (RFA) utilizes the optic gain in the Stimulated Raman Scattering (SRS) in the optical fiber and realizes the amplification of the signal optic. FRA, with very low equivalent noise and a wide gain scope, can further widen the gain bandwidth by adopting multi-wavelength optical bump, which represents the development direction of the new optical fiber amplifier.
-
Wabtec
Wabtec’s integrated family of event recorders feature an FRA Crash Hardened Memory with capacities of 8 to 128GB permit storage of Event Data from a variety of locomotive sources, storage of PTC mandated data channels, and storage of up to four HiDef video cameras. In addition to crash hardened memory, units can provide removable solid state disk storage of video from panel.
-
1250E -
Ametek Scientific Instruments
The 1250E Frequency Response Analyzer (FRA) delivers accurate measurement of gain and phase. The device under test is stimulated by a sinewave and the response analyzed at various points in the system. These responses are then correlated with the stimulus to determine the amplitude and phase relative to the generator. The ratio of the two measured signals can then be used to provide the system transfer function.
-
ZAHNER-Elektrik
Besides a potentiostat / galvanostat all our electrochemical workstations include also a frequency response analyzer unit (FRA) in their basic configuration. This makes each of our electrochemical workstations a highly versatile basis equipment for a multitude of electrochemical investigation methods on batteries, accumulators and fuel cells as well as on high impedance objects such as coatings and laminates. Due to their hardware extensions slots our instruments can be extended to multi purpose data acquisition and control test stands.
-
EchemLab XM -
Ametek Scientific Instruments
EchemLab XM includes a reference grade potentiostat and frequency response analyzer (FRA). EchemLab XM has a built-in 100 V high voltage amplifier which can be used for not only for compliance measurements but also for high voltage cell polarization. This is useful in many high solution resistance applications, for example in organic electrochemistry. In addition to high voltage, power boosters can also be integrated to combine high current and high voltage in many specialized plating applications.
-
Cleverscope Ltd.
Cleverscope Windows Application Software. Note we have added the Frequency Response Analyser (FRA) and Streaming capability to our Cleverscope application and so now it is available with all variants of our products, including units you have already bought. For power supply and power plane measurements you do need the isolated CS701 signal generator.We also now have the CS448 with four 1kV isolated channels with CMRR > 100 dB at 50 MHz.
