-
product
LATCH UP Tester
Tokyo Electronics Trading Co., Ltd.
The purpose of Latch-up testing on your components is to verify their robustness against overvoltage/ overcurrent events during their operation.
-
product
PC/104 Input/Output Module
PCM-UIO48C-16
The PCM-UIO48C-16 is a highly versatile PC/104 input/output module providing 48 lines of digital I/O. The major feature of this card is its ability to monitor 24 lines for both rising and falling digital edge transitions, latch them, and then interrupt the host processor notifying that a change-of-input status has occurred. This is an efficient way of signaling the CPU of real-time events without the burden of polling the digital I/O points.
-
product
Trip Indicator Relays
TIR
The TIR relays are designed for event recording circuit applications, where high speed event monitoring is required. The TIR relay contacts are used to record breaker functions, relay, communication and control system operations. The TIR contacts are also used to activate alarm and/or annunciator contacts.
-
product
USB-6356, 8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
782260-01
8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6356 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6356 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
USB-6341, 16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
782251-01
16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB‑6341 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6341 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PCI Digital I/O
APC464
Four 16-bit multifunction counters/timers are configurable for pulse width modulated output, watchdog timer, event counter, frequency measurement, pulse width measurement, period measurement, or one shot pulse output. The four 16-bit counters can also be configured into two 32-bit counter/timers.
-
product
High Sensitivity ESD Event Detector
MODEL 901HS
Diagnostic Tool for Manufacturing Environments Sensitive to Electrostatic Discharge - Including Electronics, Semiconductors & Medical Devices. Model 901HS is a diagnostic tool used to identify incidents or verify suspected areas of ESD activity. A voltage sensitive antenna on the unit can be positioned in ESD sensitive environments to detect problem areas of electrostatic discharges.
-
product
PXI-6624, Isolated 48 VDC, 8-Channel PXI Counter/Timer Module
778975-01
Isolated 48 VDC, 8-Channel PXI Counter/Timer Module—The PXI‑6624 performs a wide variety of counter/timer tasks, including event counting, time period/frequency measurement, quadrature encoder position measurement, pulse-width measurement, pulse generation, and pulse-train generation. It features 48 VDC channel‑to‑channel isolated I/O with eight counter/timers, 26 digital inputs, and eight digital outputs. Example applications also include the generation of retriggerable pulses, two-signal edge ...show more -
product
Electronic Circular Temperature Chart Recorder
The Circular Temperature Chart Recorder’s external stainless steel probe allows you to measure the temperature of air, gas, liquids and semi-solids. The temperature chart recorder has a quartz clock movement, motorized chart advance and temperature accuracy of ±2°F (±1°C). The chart recorder comes in °F or °C models and runs on 120V or 220V AC, 50/60 Hz. A rear compartment houses 8 AA alkaline batteries, providing up to 48 hours of continuous recording in the event of a temporary power loss.
-
product
ACoustic QUantification of IncidenTs
ACQUIT
In regions with tensions, the cease fires agreed upon along a border line are usually fragile. The global community is often asked to send in observers trying to maintain the peace and to report on violations from both sides. There is a need for well described events in the formal reporting, when, where, what kind of weapon etc.
-
product
Multi Channel Detectors
Dual, triple, quad and eight channel infrared detectors for gas analysis and flame detection sensors where more than one element or event is to be detected.
-
product
Portable Dynamometers
MD-150
The 150 series 2WD dynamometer is a compact offering that let’s you tune street cars without a large dedicated space. The 150 portable includes a pallet jack modification on one end of the frame and two bottle jacks on the other allow you to move this dyno in your shop. The portability kit lets you free up space as needed. The portable 150 is ideal for smaller shops, schools and outdoor events. There is no need to secure the unit to the ground – simply lower the unit onto the ground, hook up the light-weight composite ramps and start testing. For more information on the Portable 150 2WD series dynamometer please contact us today.
-
product
USB-6341, 16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
782250-01
16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB‑6341 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6341 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
FiberPal iOTDR
OT-9900
FiberPal OT-9900 iOTDR series, with power meter built-in, is designed with ultra portable, light, reliable and easy to use as Fiber Quick test and Troubleshooter to locating fiber connector, break and imperfections for PON DSN, FTTX, CATV and optical LANs. FiberPal OT-9900 iOTDR series detects event locations along the optical fiber and displays the results on a portable device like notebook, Tablet PC and Mobiles phones with Android 4.x or Windows XP/ Windows 7 operation system.
-
product
Condition Monitoring
Fluke Connect
Fluke is innovating industrial condition monitoring with the first system of portable sensors, a gateway and software that you can access anywhere, anytime. Each wireless sensor sends measurements every second, giving you a history of equipment performance before, during and after an event, allowing you to make preventive maintenance decisions.
-
product
Streak Camera
OptoScope S3C-1
The S3C-1 is a streak camera based on a semiconductor sensor. Like tube-based streak cameras, the S3C-1 captures changes in light along a line and records the change over time. To record the intensity values, they are sampled and stored with up to 2 GSamples/sec. The line is 65 µm wide and consists of 200 elements along its 5 mm length. Each element consists of a sensitive photodiode with a downstream amplifier.A new and special camera feature is continuous recording. This makes it possible to t...show more -
product
Dual-Mode Charge Amplifiers
Dual-mode charge amplifiers represent a versatile solution for both piezoelectric charge mode and ICP® sensors. Among the advanced features offered by models 443B01, 443B02 and 2775C are an ultra-low noise floor, sensor fault detection, overload detection, a built-in calibration reference signal, and an RS-232 port for seamless computer control. Notably, model 443B02 features a long discharge time constant selection, ideal for capturing quasi-static events lasting several seconds, a capability particularly beneficial for ballistics and ammunition testing applications. Model 2775C features AC, DC, and servo outputs.
-
product
16 SE Or 8 Diff. Input Channels, 8 Analog Output Channels, PCI Express
APCIE-3121-16-8
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
Loop Testing
Megger loop testers offer both traditional measuring techniques and state of the art “non-RCD Tripping” technology. Use these products to determine the prospective earth fault current, which is the maximum current able to flow in a phase-earth fault in an installation, and also to indicate the prospective short circuit current which is the maximum current able to flow in the event of a phase-neutral fault.
-
product
High Speed, Performance MWIR InSb Camera
FLIR X6800sc MWIR
The FLIR X6800sc is a fast, highly sensitive MWIR camera designed for scientists, researchers, and engineers. With advanced triggering and on-camera RAM/SSD recording, this camera offers the functionality to stop motion on high- speed events both in the lab and at the test range. The X6800sc has a cooled FLIR indium antimonide (InSb) detector and captures full 640 × 512 images at 520 frames per second, or up to 23,077 Hz with windowing.
-
product
16 SE Or 8 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-16-4
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
Microcalorimeters
TA Instruments’ Isothermal Titration Calorimetry (ITC), Differential Scanning Calorimetry (DSC), and Isothermal Calorimetry systems are powerful analytical techniques for in-depth characterization of molecular binding events and structural stability. Thermodynamic binding signatures not only reveal the strength of a binding event, but the specific or nonspecific driving forces involved. Structural stability profiles from DSC reveal strengths and weaknesses in higher order structure and define th...show more -
product
PXIe-5763, 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785163-01
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale F...show more -
product
Condition Monitoring
m+p Coda is a versatile monitoring system that captures and records signals coming from sensors such as accelerometers, thermocouples, strain gauges, and pressure transducers. Limit checking and alarm monitoring is provided for every active channel. The active channels are clearly displayed in a separate window, out-of-limit data can be seen at a glance. Alarm events are entered into a log file and can be reviewed at any time. You have the option to change the alarm limits online at any time without stopping the data acquisition.
-
product
Acceleration Recorders
SnapShock Plus Series
Instrumented Sensor Technology, Inc.
The SnapShock Plus (SSP) series data recorders are compact, battery powered acceleration event recorders. The new generation devices offer several improved capabilities over the standard Snap Shock model
-
product
Reliable CAN Measurement Technology
CNT evo CAN MM Series
The CNT evo is a high-precision measurement module designed for measuring frequencies, pulse widths, incremental displacement measurements, rotation angles, position measurement, event counting and period measurements.
-
product
Power Monitors
The Monitor family includes a range of products that not only measure power and VSWR but also provide hard contact alarms to protect your system in the event of a system failure – the IP-enabled, BPME is even capable of emailing a failure notification.
-
product
PCI Express Image Acquisition Frame Grabber
Xcelera-HS PX8
The Xcelera-HS PX8 has been built within Teledyne DALSA’s Trigger-to-Image Reliability technology framework. Trigger-to-Image Reliability leverages Teledyne DALSA’s hardware and software innovations to control, monitor and correct the image acquisition process from the time that an external trigger event occurs to the moment the data is sent to the host, providing traceability when errors do occur and permitting recovery from those errors.
-
product
Event Detectors
EDH Series
Is designed to monitor electrical connectors undergoing reliability testing. This instrument detects nanosecond-range electrical resistance fluctuations characteristic of malfunctioning electrical contacts.
-
product
Controls Systems for Engine Control and Combustion Analysis
NI Powertrain
NI Powertrain Controls systems incorporate the LabVIEW reconfigurable I/O (RIO) architecture to create some of the world’s most flexible and capable combustion analysis and engine control systems. The engine control systems can drive both solenoid and piezoelectric direct injectors, control timing events with 25 ns of precision, and implement novel engine control strategies such as next- and same-cycle control. The combustion analysis systems are available in both portable and higher performance stationary form factors.