Showing results: 2086 - 2100 of 3654 items found.
-
FIP-920-SM -
SYOPTEK INTERNATIONAL LIMITED
The SYOPTEK FIP series Pro Single Mode/Multimode Fiber Optic Test Kit is the perfect all-in-one fiber optic test equipment kit. The FIP kit provides a wide selection of fiber optic testing, cleaning, and inspection equipment to enable technicians to install, troubleshoot and maintain fiber optic networks. It is really a cost-effective and easy-to-use solution for testing single mode and multimode fiber optic networks, troubleshooting of fiber networks.
-
Aero Engineering Support Group
ATE Development Aero Engineering Support specializes in designs and manufacturing of a wide variety of Automatic Test Equipment (ATE) of support for military avionics, commercial avionics, industrial sector, etc. AESG is committed to providing industry leading equipment that are designed to be scalable and expandable ATE capable of providing reliable functional test solutions for any electronic assembly or Circuit Card Assembly. New from Aero Engineering Support is the A2500 system, providing:
-
SecuControl inc.
FTL testblock with dust cover and current disconnect pinThe FTL is a test block for interfacing substation devices (protection relays, fault recorders, revenue meters, ... ) to the voltage and current transformers and to other equipment on the system side of a power grid. The FTL test block uses disconnect pins to isolate the substation devices from the system side equipment. Once isolated, secondary injection can be performed using banana jacks on the front side of the test block.
-
LXinstruments GmbH
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
-
LXinstruments GmbH
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
-
Mini Mux -
Eclypse International
Eclypse International Mini Mux Control and Switch Modules, plus Software Developer Kit (SDK) provides high density test circuit switching as a complement to the Eclypse Circuit Analyzers. The Mini Mux Switching gives the user the ability to test continuity and isolation in complex assemblies with thousands of circuit paths (such as avionic back planes and chassis), while minimizing the test equipment complexity and footprint.
-
LPS Series -
Lumina Power, Inc.
The LPS series power supplies are designed for various applications in semiconductor equipment along with OEM and industrial applications. Available for use in constant current or constant voltage applications they are available in power levels from 1,000 to 13,500 Watts. Common applications include heater, filament and magnet supplies along with test and burn-in applications. All models can be paralleled for increased power and custom configurations are available.
-
Maschinenbau Haldenwang GmbH & Co. KG.
National type approval by the PTBPrinter with keyboard and digital displayFast matrix printer with graphic expressionPiezoelectric decelerometersControl and measurement electronicsElectrical equipment adjustment by means of digital displayGyro sensor for automatic compensation of the measurement error by the pitch behavior of the vehicleJacks for pedal force, pressure u. Load indicatorRS-232 interface to PC with data transfer for standard table SoftwareChargerSpare roll of paper approximately 15 mplastic suitcase
-
DSG01 -
CL System
The DSG01 is a compact and smart module that will turn your PC or laptop into a fully-functional Digital Oscilloscope , a Programmable Signal Generator and a Frequency Spectrum Analyser. No more heavy, expensive, dangerous (high voltage), power hungry and large footprint analogue scopes, instead an elegant, small, low power, fully featured and safe piece of equipment that will upgrade your lab instruments within an affordable budget.
-
MT322-107 -
ALTINEX, Inc.
The MT322-107 distributes AC power from a single AC source to multiple AC outlets. These outlets can be connected to any type of audio/video equipment. The total current supplied to all outlets must be less than 10 A. Built-in sensors alert the user by flashing the LEDs when the load exceeds 8.5 A and a warning message is sent to the RS-232 bus when the current draw is near maximum.
-
Crowcon Detection Instruments
Crowcon offers a flexible range of fixed gas detection products which are able to detect flammable, toxic and oxygen gases, report their presence and activate alarms or associated equipment. We use a variety of measurement, protection and communications technologies and our fixed detectors have been proven in many arduous environments, including oil and gas exploration, water treatment, chemicalplants and steel mills.
-
FLIR FC-Series R (Automation) -
Teledyne FLIR
The FC-Series R features on-board, non-contact temperature measurement capabilities for fire detection, safety, and thermal monitoring of substations, waste disposal, and valuable equipment. FC-Series R combines state-of-the-art image detail and on-board video analytics to provide reliable detection. Flexible alarming options include email, web and mobile apps, edge image storage, digital outputs, or VMS event notifications.
-
Kemo
We offer a range of instrumentation calibration services for Kemo products in addition to other signal conditioning and sensors. We have many decades of experience in the manufacture, test and calibration of our instruments and those of our competitors. Please refer to the list below for an example of our calibration options, all equipment used within our calibration department is calibrated and traceable to a UKAS accredited National standard:
-
ElectroStatics, Inc.
Ionization or anti static blowers are the most versatile ionizer to control or remove static electricity from plastic, paper, glass and other non conductive materials. This static control blower offers the ability to cover a large area cost effectively. This static control equipment is an excellent choice to reduce static electricity and reduce operator static shocks and production applications needing large area coverage.
-
SICK Sensor Intelligence
Inside or outside: Effective solutions for an incredibly wide range of applicationsObject detection systems detect objects irrespective of size or position, both indoors or outdoors. They are used in intralogistics to increase throughput of conveyor systems. The systems also prevent collisions in outdoor areas and ensure and increase equipment availability in steel mills, ports and other areas. Regardless of the application, system reliability means smooth process flow.
