-
product
Integrated Turbine Rotor Measurement and Assembly Platforms
iMAP
Rotary Precision Instruments UK Ltd
Improve productivity and achieve higher levels of quality by reducing inspection times and the need for costly teardowns due to inefficient rotor assembly. iMAP is the definitive system for productivity improvement in turbine rotor assembly for large volume and heavy loads such as aircraft engines and gas turbines.
-
product
eTechnician™ 2.x
eTechnician™ gives you the data and the support required to stay competitive in today’s trucking industry. Heavy-duty diagnostics on your PC was never this good—until now. We’ve combined extensive coverage for everything from commercial vehicles right down to light and medium-duty trucks. That gives you diagnostic capability for engines, transmission, brakes, body and chassis, and more.
-
product
USB-6366, 8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
781445-01
8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6366 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6366 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
SparkFun 16 Output I/O Expander Breakout
SX1509
Are you low on I/O? No problem! The SX1509 Breakout is a 16-channel GPIO expander with an I2C interface – that means with just two wires, your microcontroller can interface with 16 fully configurable digital input/output pins. But the SX1509 can do so much more than just simple digital pin control. It can produce PWM signals, so you can dim LEDs. It can be set to blink or even breathe pins at varying rates. This breakout is similar to a multiplexer or "mux," in that it allows you to get more IO from less pins. And, with a built-in keypad engine, it can interface with up to 64 buttons set up in an 8x8 matrix.
-
product
Constant Volume Sampler
CVS-ONE
The CVS-ONE series is designed for the measurement of diluted emissions from vehicles and engines. The new integrated operating platform, HORIBA ONE PLATFORM is adopted for the CVS-ONE. The hardware has been significantly downsized from previous designs, reducing test cell footprint requirements. It introduces new functions and is more user-friendly, while still maintaining high accuracy. In conjunction with the MEXA-ONE (Motor Exhaust Gas Analyzer), the system can be used to measure extremely low emission levels such as SULEV. The new CVS reliably supports emission testing requirements of today and into the future.
-
product
Pump Testing with NPSH Measurement
Test field for centrifugal and side channel pumpsfor split-case pumps or as a complete unit with customer engine.*Open tank system for recording QH characteristics*Vacuum-resistant container for NPSH measurements*Three flexible test cars with height-adjustable test motors: 5/30/90 kW
-
product
On-Board Flow Meter
DF-2200
The DF-2200 On-Board Flow Meter is a compact on-board fuel flow meter developed for our FP series Volumetric Flow Detector*. The compact body is equipped with functions such as flow rate/temperature/pressure measurement and CAN communication required for fuel consumption measurement. Adopting the same size as our CT-6700 Engine Tachometer, it can be used by stacking two units in a limited space. In addition to 12 to 24VDC of power source, an AC adapter is available as an option, which is sufficient for not only on-board measurement but also engine bench evaluation.
-
product
CESL2G
PWA212040
Your Pratt & Whitney GTF™ engines operate best when they have the latest software installed, and there's no better tool for you to keep your engine software up to date than the Bloomy Common Engine Software Loader (Second Generation). The result of collaboration between Pratt & Whitney and Bloomy, the Bloomy CESL2G is a clean-sheet design with reliability, safety, and convenience incorporated from the project’s inception.
-
product
Polarization Lambda Scan Software License
N7700100C
Enables polarization-dependent swept-wavelength multichannel measurements with the PAS LS engine and PAS IL/PDL engine, as well as measurements without varying polarization with the PAS LS engine and PAS FSIL engine.
-
product
Desktop Network Appliance Platform With Intel® Atom® Processor C2358 And 6 LAN
NA361
The NA361 1U-type compact network appliance platform supports the Intel® Atom™ dual-core processor C2358. Customers using the new NA361 also benefit from Intel® QuickAssist Technology hardware acceleration engine. The network system supports maximum up to 16 GB of DDR3 1600MHz UDIMM non-ECC memory or ECC memory, and features one 2.5” SATA HDD for storage. Six Gigabit Ethernet ports using Intel® i347 and i210 chipsets are integrated into this unit with two-pair LAN bypass function; one PCI Expres...show more -
product
PXI Precision Resistor Module 9-Channel, 2 to 52.4k
40-297-033
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI Precision Resistor Module 4-Channel, 2 to 52.4k
40-297-133
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Exacting Electric Motor Testing
The Taylor Dynamometer Electric Motor Test Stand is designed to provide maximum reliability, excellent durability and flawless performance. Using our extensive line of Water Brake engine dynamometers, Taylor Dynamometer has systems available for testing electric motors from 5 to 13,000 hp (3.7 to 9,694 kW). Include an instrumentation package to achieve your testing requirements. From simple speed, torque and power display systems with manual control to completely automated testing solutions, Taylor Dynamometer has a system to meet your testing requirements.
-
product
PCI High Density Pecision Resistor Card, 9-Channel, 2Ω To 470Ω
50-298-114
The 50-298-114 is a high density programmable resistor card with 9 channels which can be set between 2Ω and 470Ω with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
AC & DC Loadbanks
Regular load bank testing of generators provides an essential health check service to prevent diesel engine failure due to wet stacking. Wet stacking occurs due to under loading of the genset which results in wet un-burned fuel building up in the engine. This fuel build up will over time line the combustion chamber cylinders and cause a reduction of the engines rating and efficiency which will ultimately cause premature failure of the generator. Running the generator on load of 50% - 100% of the genset rating will allow the engine to reach the recommend operating temperature, which will burn off the choke deposits.
-
product
PXI Precision Resistor Module 3-Channel, 3 to 2.97M
40-297-151
This PXI Precision Resistor module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Advanced Battery Conductance/Electrical System Tester
PBT Series
Building upon the success of the PBT-100, the first battery conductance tester built for the professional technician's toolbox, the PBT-200 offers these additional capabilities: Shows available power in CCA in addition to condition and voltage. Bad Cell Detection. Advanced Starter Testing: Down arrow displays the captured low voltage from cranking the engine for simple starter analysis.
-
product
Integrated Video Management System
iVMS
The iVMS iQ Engines provide that comprehensive view of your FoQus platform assets. Management systems are available for Linear/IPTV networks (iVMS) or adaptive bitrate networks (iVMS ASM). iVMS tracks QoE and QoS data for thousands of programs across hundreds of acquisition elements to provide true end-to-end, centralized video quality management. With iVMS, you can drill down to identify and isolate the root cause of issues by program, time and location. In order to reduce repair time (MTTR), i...show more -
product
PCI Precision Resistor Card 9-Channel, 2Ω To 13.6kΩ
50-297-031
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI Precision Resistor Card 6-Channel, 2.5Ω To 773kΩ
50-297-043
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI Precision Resistor Card 4-Channel, 1.5Ω To 6.97kΩ
50-297-124
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI Precision Resistor Module 18-Channel, 1 to 31.5
40-297-010
This PXI precision resistor provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Open Standard Module (OSM)
ROM-2620
Advantech ROM-2620 OSM 1.1 Computer-on-Module is powered by NXP i.MX 8ULP SoC which includes up to 2 Arm Cortex-A35 cores in combination with one Cortex-M33 real timeprocessor and Vivante GC7000 nanoULTRA/GC328 graphics engine. It provides USB2.0, Fast Ethernet, MIPI-CSI, I2C, SPI, GPIO, PWM and MIPI DSI display for embedded applications
-
product
PXI-2510, 68-Channel, 2 A PXI Signal Insertion Switch Module
778572-10
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
PCI Precision Resistor Card 3-Channel, 3Ω To 5.82MΩ
50-297-152
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCIe 3.0 Ethernet Controller
BCM57416
The BCM57416 10GBASE-T PCIe 3.0 Ethernet controller builds upon the success of the widely-deployed NetXtreme E-Series architecture by combining a high-bandwidth Ethernet controller with a unique set of highly-optimized hardware acceleration engines to enhance network performance and improve server efficiency.
-
product
ADAQ Data Systems
Atec’s Data Acquisition and Control System (ADAQ™) is a modern, full-featured, highly integrated hardware and software solution that is applicable for use with most commercial and military turbine engine test cell applications. Built upon National Instruments’ respected LabVIEW platform, ADAQ™ is robust, versatile, user friendly, and specifically designed to handle the demanding requirements of engine testing. It links seamlessly to digital engine modules (FADECs, DEECs, EECs, ECUs) as well as ...show more -
product
Test Cell Vibration Monitoring System
The Test Cell Vibration Monitoring System is a complete package for monitoring dyno vibration levels generated during engine testing. This system was design to prevent catastrophic dyno failures.
-
product
PCIe-6323, PCI Express, 32 AI (16-Bit, 250 kS/s), 4 AO (900 kS/s), 48 DIO Multifunction I/O Device
781045-01
PCI Express, 32 AI (16-Bit, 250 kS/s), 4 AO (900 kS/s), 48 DIO Multifunction I/O Device - The PCIe‑6323 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog...show more -
product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 395kΩ
50-298-142
The 50-298-142 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 395kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.