Showing results: 106 - 120 of 1259 items found.
-
Elmeasure India Pvt. Ltd
Directly replaces 2 energy meters Sensing dual source through 240V connection Dual row display switches based on the source Displays basic and most of the power parameters Optional digital output separately for EB or DG parameters
-
ECM-1240 -
Brultech Research Inc.
Cascade several ECM-1240s to monitor all of your panel circuits! * Locate the guzzlers. * Set consumption budgets/goals. * Find loads or appliances requiring maintenance or replacement. * Determine the optimum balance between comfort and energy cost. * Reduce peak demand and SAVE MONEY!
-
GF102 -
Beijing GFUVE Electronics Co.,Ltd.
The GF102 is used to test single phase energy meter error. Adopt mature signal synthetic and power amplifier technology, high precision 500V voltage and 120A current output, accuracy 0.05%, automatically test all kinds of single phase enegy meter.
-
SP-6103 -
Shanghai Powoo Industry Develop Group Limited
- Single phase energy meter test bench - auto-calibration system - accuracy class: 0.1/0.2 class - Standard CT; 0.01/0.02 - output voltage: 0-220V9240V option); range: 0-120% - fine adjustment: 0.01% - output current: 0-100A; (option for 200A)- fine adjustment: 0.0001A (min)
-
mks Ophir
Ophir has several ways to measure intense pulsed light IPL radiation used in cosmetic treatments. The light from these sources is broadband and usually has a high divergence. Furthermore, the light source is often coupled to the skin via an index matching gel. For these reasons, we need special solutions to accurately measure the energy of the IPL pulses.
-
mks Ophir
Pyroelectric sensors for measuring repetitively pulsed energy at up to 25 kHz. These sensors use a pyroelectric crystal that generates an electric charge proportional to the heat absorbed. The response time of the pyroelectric sensor depends on the time it takes for the heat to enter the crystal and heat it up. For metallic type pyro detectors, this time is tens of μs and thus the metallic type can run at a high repetition rate. For the BF and BB type, the response time is milliseconds with a correspondingly lower repetition rate. Ophir pyroelectric detectors have unique and proprietary circuitry that allow them to measure long pulses as well as short pulses and work at a high duty cycle, i.e. where the pulse width is as much as 30% of the total cycle time.
-
StarBright 7Z01580 -
mks Ophir
*Compatible with all standard Ophir thermal, BeamTrack, pyroelectric (PE-C series) and photodiode sensors*Brilliant color large size TFT 320x240 display*Choose between Digital with Bargraph, Analog Needle, Line Plot (for laser tuning), Pulse Chart, Pass/Fail, *Position, Stability, Real Time Statistics displays*Sophisticated power and energy logging, including logging every point at up to 5000Hz with Pyro sensors*Math functions for advanced processing such as Density, Scale Factor, Normalize against base line, etc.*Can mix functions together and display the results graphically. Function results can also be logged.*USB Disk on Key (Thumb Drive) for nearly unlimited data storage.*USB and RS232 interfaces with StarLab PC applications and User Commands document
-
IT 503 & IT 504 -
Tinius Olsen
The model IT503 plastics impact tester, together with the model IT504, continues to set the industry standard for versatility, ease of operation and display of information with high resolution. The primary difference between the IT503 and the IT504 is that the model IT504 is supplied without the interlocking safety shielding.
-
PQ55A -
Beha-Amprobe
* Cpmprehensive real-time monitoring, recording and analysis of 3-phase systems* Voltage measurement (true RMS)* Current measurement (true RMS)* Power factor measurement* Phase angle measurement* Power analysis (active, apparent and reactive power)* 4. Current clamp for neutral line current measurement* Suitable for use in housing construction, offices and small businesses
-
Apogee Instruments, Inc.
Apogee silicon-cell pyranometers feature a monocrystalline silicon-cell detector that has the same spectral response as a PV module. The sensors quantify shortwave radiation being harnessed as electricity.
-
EDS -
Materials Evaluation and Engineering
EDS is an elemental chemical microanalysis technique performed in conjunction with each of the SEMs at MEE. Features or phases as small as about 1 micron can be analyzed.
-
Chauvin Arnoux Metrix
Designed for test and maintenance departments working in industrial or administrative buildings, it can be used to obtain a snapshot of the main features characterizing the quality of the electrical network.
-
EPM 2200 -
GE Digital Energy
The EPM 2200 meter measures more than 40 electrical power parameters providing a low-cost, multifunction monitoring solution for industrial and power generation applications. EPM 2200 can easily be mounted in a panel for generator monitoring, substation automation and more. The meter can also provide data to RTUs, PLCs and other control devices.
-
Shenzhen Chuangxin Instruments Co., Ltd.
It’s used to test the mechanical integrity of product enclosures and check the durability of enclosures for electrical appliances of other electrical appliances and other electronic products. If damage occurs from the Impact Hammer test, accessibility probes can be used to measure the extent or severity of the damage. The Impact Hammer simulates the mechanical impact to which electrical equipment maybe subjected.
-
Ophir
Laser beams with powers of many tens of kilowatts are becoming increasingly common in today’s industrial applications. However, as the powers increase, the stakes increase as well. In this webinar, we will discuss how to monitor appropriate laser parameters to keep high-power processes stable and predictable.