Showing results: 1141 - 1155 of 1259 items found.
-
XiRAY -
XIMEA GmbH
*High resolution direct phosphor imaging, ideal for Micro CT*Ultra-low readout noise with CCD and especially the new sCMOS sensors*Crystal clear 14 bit/pixel images*Partial readout and binning modes for enhanced sensitivity and higher speed*Non-linearity over full dynamic range <2% (of full scale) to 95% of full scale*External triggering, LVTTL*Low power consumption 6 Watt with Cooling or 2W without*Antiblooming, Enhanced Statistical Extra-Mural Absorption*Radiation hardened, Support of Energy levels 7 to 100keV*Measures just 63 x 63 x 46 mm*Peltier TE Cooled with Heatsink and optional fan
-
62075H-30N -
Chroma ATE Inc.
The 62075H-30N output power has maximum 7.5kW/30V/250A power module designed with 4U height that can be connected easily as master or slave with three units to 22.5kW/30V/750A in parallel or two units to 15kW/60V/250A in series and operated as a standalone unit via system bus. The 62075H-30N provides stable DC output cur rent sour ce and powe r for pre c i s ion measurement. It offers an advanced 250A/30V ultra high-stable ±10 ppm (current stability ±1.25 mA) with high eciency and high power factor in compliance with energy savings. In addition it has a 20 bit digital control with bright vacuum fluorescent display readout.
-
Barth Electronics, Inc
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
KM 2100 / KM 2200 -
Kusam Electrical Industries Limited
• Volts / Amps. / Hertz, Dips & Swell, Power / Energy, Unbalance, Monitor, Scope, Harmonic, Logger & Interruption functions. (KM 2200)• Inter Harmonics, Transient Voltage, Inrush Current, Flicker function not available in KM 2200.• Frequency upto 400Hz (KM 2100); 50 / 60Hz (KM 2200)• Single-phase 2W / Single-phase 3W / 3-phase 3W / 3-phase 4W.• Flash memory 128MB• TF Card 8G Memory Card for long-term measuring data storage. • Support USB port to connect to PC and analyze the data / screen shots copied by U-disk.• Support LAN port to make the remote control available, transfer the measuring data.
-
Venable Instruments
Venable Instruments has been focused on one goal: bringing the most versatile, full-featured frequency response analyzers to customers in industries where precise testing and measurement tools for power supply design is critical. Over 37 years of continual research and development has created the widest range of scalable frequency response analyzers to meet your company's current requirements, while providing a cost-effective growth path for increased testing functionality. Venable is a proven leader in aerospace, automotive, energy, defense, computer technology, academia, government research applications and virtually any industry requiring the highest standards in power supply and stability testing for repeatable and accurate results.
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Universal Impact Hammer is designed to perform impact tests for product durability. The CX-T03 meets the testing needs of industry standards such as IEC 60065, 60335, 60598, 60601, 61010 and others. The hammer simulates mechanical impact to electronic products and electrical appliances. This impact hammer is versatile -- it can be dialed to a whole range of energy values to perform tests to many different standards. A compressed spring accelerates a hammer head to hit the sample undergoing test. The spring is released from a lock mechanism by pressing the cone-shaped top of the impact hammer against the product under test. The CX-T03 is adjustable from 0.2 Nm to 1 Nm by turning a ring on the hammer.
-
Ponovo Power Co., Ltd.
As the first protection relay test set manufacturer in China, PONOVO has been always offering reliable protection relay testing equipment for customer for more than 20 years. More than 20,000 relay test kits has been supplied to users in China and other countries, including 6-phase, 3-phase, single phase relay test sets, capable of testing all kinds of protection relays, from electromagnetic relays, solid state, numerical, microcomputer relays and digital relays based on IEC61850 as well as other testings, such as, energy meter, transducer, etc. With various models with different specifications, users can definitely choose the model suitable for their testings.
-
EMC Technologies Pty Ltd
RF transmitters used in close proximity to the human body must be evaluated against human Exposure standards which set basic restrictions for the Specific Absorption Rate (SAR) of RF energy by any part of the human body. This may include two-way radios, cellular phones, smartphones, spread spectrum, Bluetooth devices, wireless EFTPOS terminals and WLAN devices used in PDA/notebook/laptop/tablet computers. In Australia and Europe, virtually all devices exceeding the power threshold of 20mW (13dBm) and used in close proximity to the human body must comply with SAR requirements. There is no such blanket exemption in the USA and Canada where each product must be assessed against frequency/power level criteria.
-
Furaxa, Inc.
*Differential output - can also provide single ended outputs, one with positive going pulse, the second with negative going pulse. * Pulse height adjustable +1 to +5V peak into 50 ohms, on positive output, with concurrent -1 to -5V peak on negative output * Produces differential pulse on positive edge of input clock * Input clock may be 20-100MHz sinewave or 0.5-100MHz square wave, producing comb to 4GHz. Usable energy to >10GHz. * Differential outputs are designed to drive matched 50 ohm loads, but can drive any load, including short, without damage. Has integral fan. * Power Requirements: -12V @ 120mA and +18V @ 90mA.
-
VP62105 -
LinkedHope Intelligent Technologies Co.,Ltd.
VP62105 supports up to 3615QE, an Intel® 4-core processor. The 3rd generation Intel® Core™ i3/i5/i7 processors have a completely new microarchitecture, enabling small-sized designs to be created with unmatched computing power, graphics performance and energy efficiency on a small footprint.VP62105 provides 4 Serial RapidIO (SRIO) x4 links for VPX Data Plane communication, 2 PCI express x8 channel for VPX Expansion Plane communication and 4 Gigabit Ethernet for VPX Control Plane communication. The rich data interchange options enable potential customers a much easier integration path for box level or system level solution designs.
-
SL1700A Series -
Keysight Technologies
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increase the need of vast battery test labs for EV battery development. Keysight developed the SL1700A Series to accelerate the development and validation of batteries. It offers a voltage range of up to 1500 V and power options between 90 and 270 kW. The new high-voltage SiC (silicon carbide) technology provides a high energy efficiency on a small footprint and helps to minimize your operating costs.
-
80-20 -
Testing Machines, Inc.
The Internal Bond Tester is designed to determine the internal bond strength of a variety of Paper and Board materials according to TAPPI T 569. The instrument design is based on a falling pendulum which creates a high speed impact on a paper specimen. The paper specimen is sandwiched between two double-coated tape substrates. The pendulum impact measures the total energy required to delaminate the internal fibers of a specimen in a "Z" type direction into two separate piles. The system also incorporates an automatic sample preparation station which allows five specimens to be accurately prepared simultaneously. The Prep Station requires a filtered air supply meeting IG4 Industrial Grade Air: ISO Class 1-4-1.
-
Dow-Key Mircowave Corporation
An electromechanical switch made primarily for routing microwave signals/RF energy from one point to another within a transmission line. Coaxial switches can be used in either an industrial environment or in the lab. These electromechanical devices are also used for RF testing equipment and in large RF communication systems and networks. Coaxial switches vary by port configuration, switch type, maximum frequency, isolation, insertion loss, voltage standing wave ratio (VSWR) and package type. Coaxial switches are able to route RF signals over a broad bandwidth from DC to 40 GHz, and are now offered with the Low PIM option which will improve Passive Intermodulation levels from -110dBc (standard switch) to -160dBc.
-
LAB-MOBI -
Electronic Test & Power Systems
The LAB-MOBI is a series of multi channel High Power Bidirectional PSUs. Each system is able to operate as either a DC Source or a DC Electronic Load. This integrated approach features high dynamics enabling the user to switch seamlessly between quadrants. When sinking energy from the unit under test the LAB-MOBI automatically inverts the DC to AC and synchronises this output to the grid. Dedicated application modes are available for battery cycling and emulation, which can be used to implement specific test routines. Other common applications the LAB-MOBI is used for include testing electric motors, fuel cells, super capacitors and solar panels. Max. Volt. Output 1000V,Min. Power 60kW, Max. Power 500kW.
-
Anderson Materials Evaluation, Inc.
Materials characterization, failure analysis, quality control, and materials and process development services are offered. Our analytical techniques allow us to assess elemental and chemical material composition, thermal properties, coating thickness, electrochemical properties, surface chemistry, surface wetting, corrosion rates and pitting potentials, contamination and degradation problems, metallography, fractography, phase transitions, static coefficient of friction, adhesive bonding strength and causes of adhesive bonding failures, surface tension and surface energy, tensile and compressive strength, bend deflection, lapshear strength, elasticity properties, UV and visible light absorption and reflection, density and porosity, and many other material properties integral to improving your products.
