Showing results: 1321 - 1335 of 1796 items found.
-
CTX 300 -
Teledyne Gas & Flame Detection
When hazardous levels of toxic gases or oxygen threaten the safety of an unclassified area, the CTX 300 detector can satisfy the most demanding safety requirements.The CTX 300 detector is designed to detect oxygen, toxic and refrigerant gases, and also uses a new sensor for CO2 detection over three different ranges: 0-5000 ppm, 0-5% vol. and 0-100% vol.The CTX 300 transmits data in record time. With a wide range of sensor options, it has the flexibility to protect many potentially hazardous environments.Maintaining the unit is easy with pre-calibrated sensors and an optional LCD display.
-
MultiSafe-MX -
Teledyne Gas & Flame Detection
The MultiSafe-MX system is intended for the protection of high hazard, high risk plant and facilities.The MultiSafe-MX is certified, by European laboratories, to comply with the applicable regulations.The panel is composed of dedicated cards, installed in 19” racks which have their own “intelligence”, programmed for active/passive fire protection, gas detection, intruder alarm and logic functions. Moreover, the MultiSafe-MX can interact with supervisory and SCADA systems via Ethernet, TCP/IP or Modbus.The MultiSafe-MX interfaces with devices using either conventional and/or addressable module inputs and outputs. These modules are used to tailor the system to customer requirements.
-
S8 TIGER Series 2 -
Bruker Optics
Thanks to HighSense technology the S8 TIGER Series 2 WDXRF spectrometer delivers for all elements accuracy and precision for industrial quality and process control. With high resolving WDXRF technology and optimal detection of light, medium and heavy elements based on the new HighSense beam path, the XRF2 mapping tool of the S8 TIGER Series delivers best sensitivity, smallest spot size, and highest resolution for small spot applications. Ergonomic and failsafe operation are vital for efficiency and best analytical data. Simple, intuitive start of samples are guaranteed with the multilingual TouchControl interface.
-
AP-D Series -
Applied Image, Inc.
All machine vision lenses will show some type of distortion. Minimizing or correcting that distortion is crucial in most applications. The ACCUplace Dot Patterns target is designed to check, verify, or quantify barrel distortion in vision systems, alignment between multiple optical systems, and can calibrate instruments with both vision and motion systems. The indexed columns and rows of dot features provide reference points that make alignment and distortion detection simple and straightforward. The AP-D is offered on four standard materials; Glass (CG) Opal (OP) Photopaper (RM) and Film (TM).
-
PerkinElmer Inc.
Whatever your application, industry requirements or regulations, we have a breadth of solutions designed to solve your separation and detection challenges. Our diverse portfolio spans techniques for liquid chromatography (LC), liquid chromatography/mass spectrometry (LC/MS), gas chromatography (GC and GC/MS), and Arnel GC engineered instruments. Plus, we offer the most comprehensive suite of sample preparation technology that includes an array of autosamplers, GC Headspace (HS) and Thermal Desorption (TD) sample handling systems, liquid injection and Solid-Phase Micro-Extraction (SPME) options, and more.
-
Fortress Technology Inc.
The Phantom Pharmaceutical metal detector provides the ideal solution for detection and rejection of the smallest contaminants in tablets and capsules. With its current GMP design and construction suited for FDA compliance, the system meets the stringent QA requirements of the pharmaceutical industry. A free IQ/OQ Validation package is included. Built with a rugged mirrored stainless steel exterior, contact parts are all removable for cleaning without the need for tools. This compact detector can be easily angled and height-adjusted to suit any press configuration. Plus, it’s the only detector that features an electrical powered lift.
-
TK8A -
Techna-Tool Inc.
BK Mikro TK8A is a scanner designed mainly for broken tool detection inside the tool changer of machining centers adding little or no additional cycle time. The controller stores up to 512 different tool lengths in memory and is controlled using 24vdc M-Code/Macro I/O combinations, Profibus, Profinet or DeviceNet. The system can check tools whose lengths vary as much as 15 inches from the shortest to longest in the changer. Each of the 512 different tools can have individual tolerance ranges set varying between 0.15 and 25.4 degrees
-
A1 / C1 / C2 -
Becker & Hickl GmbH
*bh FLIM Embedded in Nikon NIS-Elements Software*Two Fully Parallel TCSPC FLIM Channels*Compact bh Simple-Tau or Power-Tau System*Two HPM-100-40 GaAsP Hybrid Detectors*Excitation by bh ps Diode Lasers*Excellent Time Resolution: Electrical IRF Width 6.5 ps FWHM*Excellent Timing Stability*Time Channel Width Down to 813 fs*Megapixel FLIM, Up to 2048 x 2048 Pixels at 256 Time Channels*Detection Wavelength Range from 360 nm to 700 nm
-
Excelitas Technologies Corp.
Excelitas offers a broad range of single to multi-channel image intensified cameras through our renowned pco.dicam series. With extreme short exposure times down to 2.5 ns, our pco.dicam cameras offer the ability to precisely address ultra-fast processes far beyond the capabilities of any other camera type. Featuring state-of-the art scientific CMOS sensor technology, our pco.dicam intensified cameras combine high resolution, fast frame repetition rates, 16-bit dynamic range and extreme sensitivity for efficient single photon detection.
-
778835-01 -
NI
The PCI-6515 is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Thorlabs, Inc.
Welcome to Thorlabs; below you will find links to our imaging systems and components. The products below are not only designed specifically for imaging applications, but they can be easily integrated into our entire line of photonics products. This makes it easy to modify or build custom imaging systems. Thorlabs’ Selection of Imaging Systems consists of our Laser Scanning Microscopy systems and OCT Imaging Systems. Our Laser Scanning Microscopy offering includes multiphoton and confocal fluorescence microscopy systems. Thorlabs is a leader in the development of Optical Coherence Tomography (OCT) Imaging Systems. We offer complete systems as well as a selection of components that are ideal for constructing a custom OCT system. Our series of Laser-Scanning Cytometry instruments are non-confocal systems that utilize laser-spot scanning illumination. The detection system, which combines PMTs for fluorescence detection and photodiodes for absorbance and scatter detection, offers excellent quantitative cytometric performance and imaging capabilities. Our Burleigh® line or microscope platforms, micromanipulators, and accessories provide leading edge stability and control for electrophysiology research, and our line of Optogenetics equipment includes fiber optic components and light sources for in vivo optical stimulation for neuroscience research.
-
Circutor, sa
Portable network analyzers are essential for conducting energy audits as well as for reviewing the quality of the power supplied and the consumption in electrical installations. They provide for real-time recording and monitoring of electrical parameters, anywhere in an electrical installation, for the conduct of energy improvement studies, as well as for the detection of problems related to the quality of supply and consumption.
-
Sanwa Electric Instrument Co., Ltd
Laser Power Meters measure the energy output of laser beams for testing or laser system applications. Laser Power Meters use detection sensors to determine the intensity of a laser beam's energy output. Laser Power Meters are designed to analyze lasers within a particular range of wavelengths or intensities.
-
400SW -
Tokyo Electronics Trading Co., Ltd.
Semi-automated ESD tester featuring Ecdm 400E, Universal ESD Simulator. Used with a manual wafer probing system or a die manipulator, wafer or die level semi-auto ESD test can be done, as well as packaged device test. Damage is detected by V-I curve or leakage current change detection.
-
Mors Smitt Group
The transducers are based on compensating the magnetic field by a closed loop system. Ensure high accuracy of voltage and current measuring in railway traction or substation power equipment for protetion against power surges, overload, ground fault detection. Hall effect measurement to offer maximum protection in railway applications.
