Showing results: 136 - 150 of 152 items found.
-
PAS 9716/AO-SMT -
Precision Analog Systems Co.
The PAS 9716/AO provides sixteen channels of sixteen-bit Analog Output. The card can be used in VME systems with A16, A24, or A32 addressing, and data writes of 16 and 32 bits are supported. DIP switches are used to configure the width of the address bus. The data bus width is specified by the instruction. Highspeed voltage output DAC’s, with 6 uSec typical settling times are used on this card .The DAC output signals are available on a 37 pin D connector mounted through the front panel. Two digital output signals are also provided on the output connector.
-
DP Series -
Semiconductor Circuits, Inc.
The DP family is an economically priced high performance series of regulated DC/DC converters offering single and dual outputs. Features include MOSFET design operating at a switching frequency of 100Khz, continuous short circuit protection, LC input filter, 500 Vdc I/O isolation, and an operating temperature range of -25°C to +71°C with no derating. These miniature converters maintain excellent regulation over varying line and load conditions (0.2% for line and 0.5% for load). They are packaged in an IC compatible 24 pin DIP configuration measuring 1.25” x 0.8” x 0.4” high.
-
Mornsun Guangzhou Science & Technology
MORNSUN 1-1000W wide input DC DC converters offer 2:1/4:1/7:1/8:1/10:1/12:1 ultra-wide input voltage range and single or dual outputs with multiple packages, which are designed to meet a variety of packaging requirements, such as SIP, DIP, SMD, open frame, brick, chassis mounting and DIN-Rail. These wide input DC DC converters can be widely used in industrial control, medical devices, power electronics, instrumentation, railway transportation and telecom, etc. As a professional wide input DC DC converter manufacturer, we hope that these high efficiency, excellent quality and cost-effective wide input dc dc converters are an ideal fit for your application needs.
-
Mornsun Guangzhou Science & Technology
An isolation amplifier is an amplifier that provides isolation between the input and output of the circuits, including isolation between their associated power supplies. MORNSUN offers different types of analog isolation amplifiers, such as acquisition type signal conditioning modules, output isolation signal conditioning modules, two-wire loop power supply signal conditioning modules and signal isolators, etc. These analog isolation amplifiers feature excellent temperature drift characteristics of less than 50PPM/℃ across the entire operating temperature range of -40 ℃ to +85 ℃ and achieve isolation transmission, signal conversion (programmable for some models), HART communication, signal amplification, port protection and other functions. SIP, DIP, SMD and DIN Rail packages are optional.
-
Xeltek Inc.
Xeltek engineers work around the clock to maintain the largest device library in the industry, so new devices are being added on a daily basis for EPROM, Paged EPROM, Parallel and Serial EEPROM, FPGA Configuration PROM, FLASH memory (NOR), BPROM, NVRAM, SPLD, CPLD, EPLD, Firmware HUB, Microcontroller, and MCUs. The majority of SuperPro universal programmers come equipped with a ZIF socket supporting up to 144 pins for programming a wide range of DIP devices; other chip package supported includes SDIP, PLCC, JLCC, SOIC, QFP, TQFP, PQFP, VQFP, TSOP, SOP, TSOPII, PSOP, TSSOP, SON, EBGA, FBGA, VFBGA, uBGA, CSP, and SCSP.
-
eBOX560-500-FL -
Axiomtek Co., Ltd.
The eBOX560-500-FL is an Intel® Skylake-based fanless embedded system with compact size and full-featured I/O interface. To bring both excellent performance and ultra-low power consumption, the palm-sized embedded box PC is powered by the 6th generation Intel® Core™ i7-6600U or Celeron® 3955U processor (formally codename: Skylake). One 260-pin DDR4-2133 SO-DIMM socket with system memory up to 16 GB is available. The power efficient IP40 embedded system supports 12V DC input with screw-lock and features a user-friendly AT/ATX DIP switch. The compact eBOX560-500-FL is suitable for Industrial Internet of Things (IIoT) solutions, digital signage, retail equipment, smart factory automation, thin clients, industrial controller systems and many more.
-
Mornsun Guangzhou Science & Technology
MORNSUN DC DC switching regulator is the high-efficiency non-isolated DC DC converter with the packages of SIP, DIP, SMD, DFN or chassis mounting available, and delivers no-load input current as low as 0.1mA, operating temperature as high as 105℃ and high efficiency up to 97%. They are pin-out compatible with LM78xx linear regulators (SIP package). The newest micro-size non-isolated DC DC switching regulator K78-R4 series released with an ultra-thin DFN package has undergone a fundamental change in dimension and packaging which is manufactured via the Chiplet SiP (system in package) process, and its appearance has changed from simpleness and roughness to refinement. With technology innovation, the R4 series enables you to save space, save cost, free your designs and meet your increasing high requirements.
-
Mornsun Guangzhou Science & Technology
MORNSUN transceiver modules include integrated high efficiency CAN, RS485, RS232 isolated transceiver module, protocol conversion module and serial port to ethernet transceiver module. These industrial bus transceiver with DIP, SMD, SOIC and DFN optional packages features compact size, surge and ESD bus protection, a maximum isolation voltage up to 5,000 VDC and a wide operating temperature range of -40°C to 85°C, even up to 105°C, etc. Coupled with the use of IC integrated technology, the isolated transceiver module can easily be embedded in the user's end equipment, and achieve fully-functional bus network connectivity and data communication. Check out these isolated transceiver modules with a reasonable price along with high performance and we hope that they are an ideal fit for your application needs.
-
781155-01 -
NI
2-Channel, 8 V, ±3 A PXI Programmable Power Supply—The PXIe‑4154 is a specialized programmable power supply for battery simulation. It is designed to simulate a lithium‑ion battery cell’s transient speed, output resistance, and 2‑quadrant operation (source/sink). Critical to many RF and wireless applications, the simulator’s fast transient response time allows it to rapidly respond to changes in load current with minimal voltage dip, which makes the PXIe‑4154 ideal for powering devices under test (DUTs) such as RF power amplifiers, cellular handsets, and a variety of other mobile devices. To model the behavior of a battery more accurately, you can use the onboard programmable output resistance to simulate a battery’s internal resistance. For quiescent and standby current measurements, the PXIe‑4154 features integrated current measurement.
-
TP450-250XM-W5 -
TEAM SOLUTIONS, INC.
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
TP450-50XM-W5 -
TEAM SOLUTIONS, INC.
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
Mornsun Guangzhou Science & Technology
Mornsun AC/DC On-board Converter, one of the best-selling AC to DC converter power supplies, has a good market in the wholesale of AC to DC converter modules. On-board AC to DC converter modules are more frequently used in emerging applications. MORNSUN is expanding and enhancing its portfolio of board mount AC to DC converters to provide customers with a diverse selection of AC/DC converter module power supply in terms of package configurations (SIP, DIP, open-frame, chassis mount, etc.), input/output voltage options and multiple protections. These PCB mount AC to DC power converter modules cover power levels from 1W to 1000W, featuring compact size, standard or extra wide input voltage range, wide operating temperature range, high reliability, etc. Perfectly meet your design requirements for AC to DC converter power supply modules in different industrial applications.
-
Electron Plus
The ASA240 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software, with the ASA240 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.The built switching matrix (40 x 2) is easily configured from the software and maybe used with adaptors (such as DIP or SO) to speed up testing of boards, or maybe connected to a ‘bed-of-nails’ to facilitate rapid testing of boards in production.With the ASA240 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.
-
Extech PQ3350 -
Extech Instruments Corporation
Power measurements and analysis + datalogging of single and 3-phase/3-wire or 3-phase/4-wire systems (up to 52,428 single phase readings or 17,476 3-phase readings). Large backlighting LCD displays up to 35 parameters in one screen. Clamp-on True RMS power measurements with on-screen Harmonics display. Simultaneous display of Harmonics and Waveform. Display of Waveform with Peak Values (1024 samples/period). Analysis of Total Harmonic Distortion (THD-F). Maximum Demand (MDkW, MW, kVA, MVA) with programmable period. Adjustable CT ratio (1 to 600) and VT ratio (1 to 3000). Graphic Phase diagram with 3-Phase system parameters. 3-phase Voltage or Current Unbalanced Ratio (VUR, VIR) and Unbalanced Factor (d0%, d2%). Calculated Unbalanced Current through Neutral Line (In). Capture 28 Transient events (including Dip, Swell and Outage) with programmable threshold (%). Optically isolated USB interface with software to download Waveforms, Power Parameters and Harmonics. Includes 4 voltage leads with alligator clips and retractable plunger clips, 8 AA batteries, universal AC adaptor, software, USB interface cable, and case. Current Probes sold separately.
-
Extech PQ3350-3 -
Extech Instruments Corporation
Complete with 3000A 18" flexible current clamp probes. Datalogging of single and 3-phase/3-wire or 3-phase/4-wire systems (up to 52,428 single phase readings or 17,476 3-phase readings). Flexible clamp probes can be used for wrapping around bus bars and wire bundles. Large backlighting LCD displays up to 35 parameters in one screen. Clamp-on True RMS power measurements with on-screen Harmonics display. Simultaneous display of Harmonics and Waveform. Display of Waveform with Peak Values (1024 samples/period). Analysis of Total Harmonic Distortion (THD-F). Maximum Demand (MDkW, MW, kVA, MVA) with programmable period. Adjustable CT ratio (1 to 600) and VT ratio (1 to 3000). Graphic Phase diagram with 3-Phase system parameters. 3-phase Voltage or Current Unbalanced Ratio (VUR, VIR) and Unbalanced Factor (d0%, d2%). Calculated Unbalanced Current through Neutral Line (In). Capture 28 Transient events (including Dip, Swell and Outage) with programmable threshold (%). Optically isolated USB interface with software to download Waveforms, Power Parameters and Harmonics. Includes 3 flexible current clamps, 4 voltage leads with alligator clips and retractable plunger clips, 8 AA batteries, universal AC adaptor, software, USB interface cable, and case.
