Showing results: 1291 - 1305 of 5316 items found.
-
40-667-011 -
Pickering Interfaces Ltd.
The 40-667 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.Each multiplexer channel can support 30A of continuous current and switch up to 40V signals. The switches can sustain inrush currents in excess of 120A. AC or DC signals can be switched since the switch is polarity insensitive.Note: The 40-666-011 supersedes the 40-666-001 which is functionally the same but with some changes in specification. A data sheet for the 40-666-001 can be found in the 40-666/667 User Manual.
-
POLARES -
PASI srl
Till this moment the use of Electrical Resistivity Tomography (ERT) for geology has always been basically the same since its debut, based on the original vertical Electrical Soundings (VES) principles: applying a continuous current to two stakes inserted into the ground and measuring the corresponding voltage between other two. The applied current and thus the relative tension have always been continuous, with an inversion in polarity for each measure. The new tool POLARES uses an alternate current, instead, sinusoidal type, with an adjustable frequency.
-
HMS7000 -
ECOPIA
Classic hall effect measurement system is to read voltage difference made between both diagonal sides, when flowing current and applying magnet field strength, in perpendicular to flowing current direction. - Photonic hall effect measurement is to read various electrical properties by illuminating light of “various range of wavelength” on the sample, in addition to flowing current and applying magnet field strength. - It is great to see “RGB (Red, Green, Blue), Light intensity vs carrier density, carrier mobility, resistivity, hall coefficient”
-
Teledyne Marine RD Instruments
For decades, Teledyne RD Instruments has been the preeminent supplier of Acoustic Doppler Current Profiling (ADCP) instrumentation for open ocean applications. Teledyne RDI’s vessel-mounted Ocean Surveyor family of ADCPs continues to raise the bar, collecting detailed maps of the distribution of water currents and suspended materials through the water column and along the ship’s path - at depths and resolutions previously considered unattainable. In real time, the ADCP is also used to aid in situ decision-making, to adapt field operations, and to understand current regime characteristics.
-
Ampstik®+ -
SensorLink
Use the Ampstik+ to safely take accurate current measurements when performing high voltage live-line load checks for balancing, switching, or breaking load. This high voltage ammeter measures in every electric utility setting with a linear current sensor to accurately measure .5A to 5000A, while in voltage environments up to 500kV. The opening of the amp sensor is electronically closed, while external currents are electronically rejected. This design enables the user to measure an individual conductor within close proximity to adjacent conductors without interference errors.
-
IPTN16 -
Holding Informtest
*The module provides output of constant stabilized voltage through 16 independent channels in 2 ranges ± 2 V and ± 10 V with a step of 5 mV, as well as a stabilized current of ± 10 mA with a step of 5 μA.The IPTN16 module is intended for use in information measuring VXI systems and can be used to power resistive temperature sensors or strain gauges with voltage or current with an accurate and stable value.*The IPTN16 module can also be used to simulate voltage or current sensors when checking measuring instruments and channels of measuring systems.
-
TSMC 22ULLDCDC -
DOLPHIN Design
*Ultra-low quiescent current (< 250 nA) to ensure minimum current consumption in deep sleep / hibernation mode*High efficiency at light load to extend battery lifetime*Low ripple value to supply noise sensitive and RF loads*1 uH inductor*Ultra-small area for reduced silicon cost
-
Analog Devices Inc.
Analog Devices parametric measurement units (PMU) and device power supply (DPS) products provide a flexible range of voltage and current source/measurement capability to meet a wide range of cost-sensitive test application needs. The DPS will source currents to 1.2A and multiple devices can be ganged for even higher power applications.
-
MZC-304 -
Sonel S.A.
# Measurements of impedance in a short circuit loop.- L-PE circuit,- L-N, L-L circuit,- L-PE(RCD) circuit - without tripping the circuit breaker > 30mA.# Low voltage resistance measurement:- continuity measurement - DC current +200mA with wire resistivity reset- low current resistance measurement with accoustic signalling,
-
PQA-300 -
Radian Research, Inc.
PQA-300 Power Quality Analyzer offers the latest functionality and measurement technology designed specifically for the Utility industry. The PQA-300 is a compact solution to address; Flicker PST and PLT, Voltage and Current imbalance, Sags, Dips and Swells, harmonics, inter harmonics, THD, RMS Voltage and Current, Phase and Time measurement.
-
Hilkar
Reduced Voltage Motor Starting Panels are designed for starting of squirrel cage induction and synchronous motors. A RVMS Panel reduces the torque by temporarily reducing the voltage and/or current input. It reduces voltage applied to the motor during start up causing lower starting currents from the connected grid.
-
REOLOAD 310 -
REO Ltd.
A three phase load bank rated for 48kW, with fan cooling. The front panel layout includes a switch panel for configuring the separate resistor modules to give the required resistance and current range. There are also digital panel meters for displaying the phase voltages and currents. An interface for PLC control is also provided.
-
NF Corp.
low noise wideband current amplifiers (current to voltage converter) with a high gain and wide frequency band.CA261F2 and CA-461F2 are low noise voltage amplifiers which realize high precision signal processing and high density mounting by using single-in-line package which has six-surface strict shield.
-
MASTER -
Lifasa - International Capacitors, SA
It measures the reactive power needs of an installation and gives the corresponding capacitor connection and disconnection orders to keep the cos φ preset. At the same time it allows to measure the main parameters of an installation (voltage, current, harmonics, active power, reactive power, etc.), by using 1 or 3 current measurement transformers.
-
7124A -
Peaceful Thriving Enterprise Co Ltd
This is a low power consumption, high accuracy, and stable hand held 3 1/2digits (2000 counts) multimeter; with special designed IC to support true RMS measurement. It performs measurements of DC voltage / current, true RMS AC voltage / current, resistance, diode, continuity, and non-contact voltage sensing.
