-
product
Power Supply 650W
UEP10M52-53 / CEP10M52-53
The UEP10M52 series is a UEP10M variation with a maximum current output on +6V or -6V (asymmetric) and without +/-12V for use in CERN type CAMAC crates with a maximum 650W power output. The power supply has all the standard features of the UEP10 family as high precision and lowest noise DC outputs and a cut-off protection for overload, over- / and under voltage and over temperature failures.
-
product
High Voltage Surge Current Monitors
HVSCM
Designed to be used with the Model HVST High Voltage Surge tester. The Surge Current Monitor allows simultaneously surge testing 20 units. The Surge Current Monitor monitors the current going through each unit under test at the time of the surge. If a unit under test breaks down or leaks, the Surge Current Monitor will identify the bad unit by lighting the corresponding LED. The most important features of the surge tester are its ability to test the entire winding insulation system. A high volta...show more -
product
Low Input Bias Current Op Amps (≤100 pA)
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
product
PCI/PCIe Bus Extenders
Enables PCIe x16/x8/x4/x2/x1 boards to be rapidly tested, removed and swapped without having to reboot or power down the host system. Enabling rapid production testing and engineering debug, the hot insertion, current reporting, overcurrent indication and limiting and voltage margining capabilities make this board the highest performance PCI-e bus extender in the industry.
-
product
HPA-64 General Purpose Probes
Current Rating (Amps): 3Average Probe Resistance (mOhm): 50Test Center (mil): 100Test Center (mm): 2.54Test Center Remark: max. test center 187 mil / 4,74 mmFull Travel (mil): 50Full Travel (mm): 1.27Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 375Overall Length (mm): 9.53Overall Length Remark: Exact length depends on selected tip: Tip 1,4, 7: 0,375″; Tip 2,3,9,10: 0,365″; Tip 8: 0,385″
-
product
Alternate 1.30 (37.00) - 4.50 (128.00) General Purpose Probe
HPA-1A-1
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 655Overall Length (mm): 16.64
-
product
Insulation Resistance Tester
Aarohi Embedded Systems Pvt. Ltd
Aarohi make device enable us to measure electrical leakage in wire, results are very reliable as we shall be passing electric current through device while we are testing. The equipment basically uses for verifying the electrical insulation level of any device such as motors, cables, generators, windings, etc.
-
product
AC & DC Analog Leakage Meters
2108 EL
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Four functions : DC current, AC current, AC+DC current, and ACV measurement.● Three input resistance ranges: 1kΩ,1.5kΩ and 2kΩ.● 200uA full scale value.● ±2.5% full scale value accuracy.● Built-in overload protection circuit.● Robust, compact and easy to carry.
-
product
Bench Power Supply, Linear, Programmable, 1 Output, 0 V, 30 V, 0 A, 5 A
72-2710
The 72-2710 from Tenma is a single channel programmable bench top power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +20mV (voltage), ≤0.5% +10mA (current).
-
product
PXI/PXIe Analog Output/Current Loop Simulator Module - 8 Channel
43-765-003
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
1U Power Supply ModelsAC-DC Single Output
Switching Power Supplies (to 720 watts)
The 1U family of programmable AC-DC power supplies sets a new standard for flexible and reliable power for your application. Available in a Rack Mounting or Benchtop at 720W power levels with single output voltages ranging from 3.3 to 135V and current capabilities up to 70A.
-
product
High 1.80 (51.00) - 12.60 (357.00) Switch Probe
TSP138-H230-3
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 138Test Center (mm): 3.50Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,760Overall Length (mm): 44.70Switch Point (mil): 67Switch Point (mm): 1.70
-
product
PXI I/O Module for Sound and Vibration
JSV-4498-PXI
16-channel ICP analog voltage input Maximum sample rate: 204.8KS/s; simultaneous acquisition Analog-to-digital converter: delta-sigma, 24 bits Phase accuracy < 0.02deg@10KHz Maximum analysis bandwidth：96KHz Input range from ± 10 V to ± 316mV Coupled mode：AC Signal conditioning: anti-aliasing filter Digital filter: user-defined low pass, high pass, band pass, band stop Dynamic range：114 dB ICP Current：0-4 mA, optional Overload indication: software displa
-
product
Barometers
Ideal for recording ambient changes in lab, monitoring conditions affecting sample analysis, and assisting in prediction of weather changesUnit includes a barometer, thermometer, clock, altitude adjustment, and weather symbol forecasting symbolsAdjustable altitude compensation from –900 to 3600 feet (–300 to 1200 meters)Barometric trend shows current reading, previous 1, 3, 6, and 12-hour readings in bar chart f
-
product
Three Phase Multifunction Static kWh Meter
SY 1065
Hong Kong Songyang Industrial Ltd.
This kind of meter integrates many functions into one, realizes the functions of time-sharing electricity measurement for active double-direction, measuring demand, sinusoidal reactive, calculating power factor, displaying and tele-transmitting present voltage, current, power and load curve etc. and it realizes the function of recording all the missing voltage, missing current and the percent of pass for voltage,
-
product
Custom Socket
Different structure:open top,clamshell or handlerOne type: design socket according to customer's PCB.The other type : customer layout PCB according to socket datasheet.Please tell device voltage,current,frequency and temperature and other requirements.
-
product
19 ″ DC Laboratory Power Supplies
*Power from 750W to 2.4kW*Output voltage up to 1200V*Output current up to 160A
-
product
Three-Phase Motor Reverser, 480Vac, up to 7.5W, 12-30Vdc Control Voltage, 1600V Peak Voltage, Zero-Cross Switching
Series EMCRT
Three-Phase Motor Reverser, 480Vac, up to 7.5kW, 12-30Vdc control voltage, 1600V peak voltage, zero-cross switchingAvailable options include:EMCRT48D50 Motor current: 8.5A Mains voltage: 24-520Vac I2t: 1500A2s EMCRT48D75 Motor current: 16A Mains voltage: 24-550Vac I2t: 500A2s
-
product
Battery Monitoring System
iPQMS-C256
Around-the-clock UPS protection is achieved through battery monitoring systems that monitor and trend battery health multiple times per day. The iPQMS-C256 is designed for 480V UPS Systems. Ohmic resistance and voltage measurements (per jar) are taken as often as every five minutes. System DC current, DC voltage, and temperature are measured in real-time.
-
product
PXIe-4464 , 204.8 kS/s, 119 dB, 6 Gains, AC/DC-Coupled, 4-Input PXI Sound and Vibration Module
783087-01
204.8 kS/s, 119 dB, 6 Gains, AC/DC-Coupled, 4-Input PXI Sound and Vibration Module—The PXI‑4464 delivers simultaneous sampling on all channels. In addition, the PXI‑4464 includes built-in antialiasing filters that automatically adjust to your sampling rate, six software-selectable input gains ranges, and TEDS smart sensor support for error-free setup. The IEPE excitation circuit can deliver current for high-power sensors and strong data integrity over long sensor cable runs.
-
product
Battery-Powered Bounding Tester
MRC 100S–BD-3
The MRC 100S-BD-3 Bounding Tester is a battery-powered portable digital ohmmeter, which can be used, for example, for testing the ground connection in any section of an aircraft using different measuring currents (up to 10A). This high current ensures that any uncertain connections are recognised.
-
product
Standard- 27.20 (771.00) - 64.00 (1814.00) Godzilla High Current Probe
HC375F-4
Current Rating (Amps): 100Average Probe Resistance (mOhm): 25Test Center (mil): For more details, please contact us.Test Center (mm): For more details, please contact us.Full Travel (mil): 360Full Travel (mm): 9.14Recommended Travel (mil): 250Recommended Travel (mm): 6.35Overall Length (mil): 3,110Overall Length (mm): 78.99
-
product
Autoranging Digital Multimeter w/Bargraph
HH2209
High Accuracy (Basic Accuracy 1.0%)Jumbo LCD display 3260 count, 21mm figure heigh with BaragraphAuto Ranging or Manual Ranging at your choiceHigher Voltage test up to AC 750V and DC 1000VHigher Current test up to 20AResistance test up to 30MΩTemperature test range from -4oF or 1832oFWide Frequency test range up to 300kHzDiode test, audible continuity check and Transistor testLow Battery Indication
-
product
Potentiostat / Galvanostat / Impedance Analyzer
PalmSens4
PalmSens4, is a USB and battery powered Potentiostat, Galvanostat, and optional a Frequency Response Analyser (FRA) for Electrochemical Impedance Spectroscopy (EIS). The PalmSens4 has a large potential range (-5V to 5V or -10V to 10V) and current range (100 pA to 10 mA) with a high resolution and low noise. This instrument is a complete laboratory instrument but its compact and rugged design makes it also ideal for field work.
-
product
Ammeter
AC Moving Iron Meter
Moving-iron instruments are generally used to measure alternating voltages and currents. In moving-iron instruments the movable system consists of one or more pieces of specially-shaped soft iron, which are so pivoted as to be acted upon by the magnetic field produced by the current in coil.
-
product
Amp Clamp
PPDCM80
The Power Probe Digital Clamp Meter is an 80amp, auto-ranging clamp meter designed specifically for the automotive technician. This meter is rated CAT III 600V and can measure Volts, Amps, Ohms, Frequency and Temperature, necessary for automotive electrical testing. This meter’s diagnostic applications include (but are not limited to) Parasitic Draw, Crank Current testing and HVAC Temperature testing.
-
product
PXI/PXIe Wide Current Range Matrix Module, 6x8, 2-Pole, Y Loop-thru
40-514-001
The 40-514-001 (PXI) and 42-514-001 (PXIe) are low density matrices in 6x8 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
product
HV Breakout Modules
The HV Breakout Modules (BM) are specifically designed for safely measuring directly from HV voltage power cables. Currents and voltages are measured directly and the raw data is acquired at up to 2 MHz per channel. With the Vector eMobilityAnalyzer software, which is optimally paired to the CSM HV Breakout Modules, real time power analysis is also possible.
-
product
Three-Phase Transformer Demagnetizer
DEM60C
After a DC current test, such as winding resistance measurement, the magnetic core of a power or instrument transformer may be magnetized (remnant magnetism). It can cause various problems such as wrong diagnostics, inaccurate measurements on a transformer, inrush current at the start-up of a power transformer, or incorrect operation of protective relays due to magnetized CT cores. The best way to eliminate this source of potential problems is to use demagnetizer on the power or instrument trans...show more -
product
100BASE-T1 Automotive Ethernet Protocol Analyzer
100BASE-T1
Prodigy Technovations Pvt. Ltd.
100BASE-T1 Automotive Ethernet Protocol Analyzer is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. Automotive Ethernet interface scales up to address current and future needs of in-vehicle bus speed requirement. Need for higher-speed in-vehicle bus is increasing to support feature-rich ADAS and connected vehicle needs. Two-wire full duplex 100BASE-T1 PAM 3 signaling is the choice of interface bus to address these needs
