Showing results: 6766 - 6780 of 6935 items found.
-
40-735-912-S4 -
Pickering Interfaces Ltd.
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. This 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
40-735-902-S3 -
Pickering Interfaces Ltd.
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
40-735-912-S1 -
Pickering Interfaces Ltd.
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
PCR-LE Series -
Kikusui Electronics Corp.
The PCR-LE Series is a new line of advanced multifunctional AC power supply that has been developed from our PCR-L/LA Series (linear amplifier type). The PCR-LE Series provides high reliability and can be applied to various applications, by taking advantage of the features that can control broadband waveform freely. Moreover, the PCR-LE Series can be configured as a core device of a test system combined with E-loads and Power Analyzers for “Grid Connection Testing” in regard to dispersed power generation, such as Solar Power, Wind Power, Fuel Cell, and Gas Engine referred to as “New Energy Field”. With various options, the low frequency immunity test and various power enviroment tests are supported. The options for parallel operation and three-phase operation enable you to expand a single-phase system up-to 27kVA, single-phase three wires up-to 54kVA, and a three-phase system up to 81kVA. The system can be applied to a large-scale EMC site for testing of industrial high-capacity air conditioners.
-
SHB230 -
Axiomtek Co., Ltd.
The SHB230 is high-performing PICMG 1.3 half-size single board computer.The SHB230 based on the Intel® Q87 PCH is designed to support 4th Generation Intel® Core™ i7/i5/i3 and Celeron® processors (codename: Haswell/Haswell Refresh) in the LGA1150 socket.The slot CPU card is equipped with two DDR3-1333/1600 SO-DIMM sockets with up to 16 GB memory capacity to meet customers needs.The PICMG 1.3 specification brings advantages of PCI Express to this single board computer that offers four PCIe x1 or one PCIe x4, and one PCIe x16 routed to the backplane.The onboard two SATA interfaces support RAID 0/1 functions to ensure reliable storage for multiple applications.Utilizing with the latest Intel® technologies, this PICMG 1.3 system host board is an ideal solution for DVR, medical equipment, industrial automation, process control, and network security market.
-
CEM312 -
Axiomtek Co., Ltd.
The CEM312 supports Intel® Atom® x5 and x7 processors in a board size of 95 x 95 mm. It has two 204-pin DDR3L-1600 SO-DIMMs with up to 8GB of system memory and an optional eMMC for a maximum of 64GB memory. The COM Express Type 6 module is integrated with Intel® Gen 9 graphics and supported with DX12.0, OCL 2.0 and OGL 4.3 for immersive graphics and media performance with a resolution up to 4K. Moreover, the industrial grade system on module can operate under wide temperature ranging from -40 to 85°C (-40°F to 185°F). The Intel® Atom®-based computer module also offers diverse comprehensive I/O interfaces to meet requirements for a variety of industrial applications. The CEM312 can serve as an excellent solution for graphics-intensive, industrial IoT applications such as industrial control, medical imaging, digital signage, gaming, military, and networking.
-
FDM Environment Makers
This Environmental test chamber is designed for all kind of conditions The thermo-glass door is made with quadruple tempered glass, in order to give you a full view of the internal conditions without penalizing your test perfomances.The conditions uniformity during the test is improved through an advanced ventilation air system with whom the chamber is equipped.This machine is automated by a touch screen controller, and gives your test the best conditions with also more control for users. Set your test directly on it and push the start button! In the end, download the results via USB pen drive.Last but not least, besides excellent performances, what other features would you look for in a machine? Easy maintenance for sure! We developed a way to facilitate the cleaning of the condenser and of the air filter. Furthermore, the electrical compartment was placed on the lateral side for an easy access. Is that it? Of corse not, we can also offer a full customization of the chamber, according to any requirement.We are the Environment Makers.
-
MB Dynamics Inc.
MB Dynamics delivers steering test equipment to help fulfill a myriad of application test requirements, or jobs-to-be-done. The steering test equipment consists of software for multi-test-head, synchronized MIMO closed-loop control and data acquisition; rotary servo motors for attachment to a steering spline or wheel; electrodynamic shaker systems; long-stroke linear motor actuators; pneumatic actuators; column stands for mounting steering column; gear fixture for mounting the gear; instrumentation (force, torque, displacement, rotary position, acoustic, acceleration); fixtures for mounting gears and columns; brackets, clamps, and fixtures for holding test items; jounce/rebound fixtures and tilt positioners for aligning input forces with tie rods at angles; software and associated data acquisition hardware up to 16 channels for recording, analysis and evaluation of in-lab steering noises and accelerations, road load data acquisition, and general Sound & Vibration analysis; and engineering services to accelerate test effectiveness.
-
45-100kw -
Shenzhen Setec Power Co., Ltd.
Solar pumping system is composed of a solar array,a pump and a solar pumping inverter. Based on the design philosophy that it is better to store water than electricity , there is no energy storing device such as storebattery in the system. The solar array,an aggregation of many solar modules connected in series and parallel , absorbs sunlight radiation and converts it into electrical energy , providing dynamical water for the whole system. The pumping inverter controls and adjusts the system operation and converts the DC produced by solar array into AC to drive the pump , and adjust the output frequency intensity to realize the maximumpower point tracking (MPPT) . The pump, drive by 3-phase AC motor,can draw water fromthe deep wells or rivers and lakes to pour into the storage tank or reservoir , or directly connect to the irrigation system ,fountain system,ect. According to the actual systemdemand and installation conditions,different types of pump such as centrifugal pump, axial flow pump,mixed-flow pump or deep-well pump can be used.
-
22-37kw -
Shenzhen Setec Power Co., Ltd.
Solar pumping system is composed of a solar array,a pump and a solar pumping inverter. Based on the design philosophy that it is better to store water than electricity , there is no energy storing device such as storebattery in the system. The solar array,an aggregation of many solar modules connected in series and parallel , absorbs sunlight radiation and converts it into electrical energy , providing dynamical water for the whole system. The pumping inverter controls and adjusts the system operation and converts the DC produced by solar array into AC to drive the pump , and adjust the output frequency intensity to realize the maximumpower point tracking (MPPT) . The pump, drive by 3-phase AC motor,can draw water fromthe deep wells or rivers and lakes to pour into the storage tank or reservoir , or directly connect to the irrigation system ,fountain system,ect. According to the actual systemdemand and installation conditions,different types of pump such as centrifugal pump, axial flow pump,mixed-flow pump or deep-well pump can be used.
-
NI
The USRP Software Defined Radio Stand-Alone Device consists of an onboard processor, FPGA, and RF front end. You can program this device using either LabVIEW Communications System Design Suite or an open-source software workflow, depending on the operating system you choose. You can provision the device with NI Linux Real-Time, Linux Fedora, or Linux Ubuntu real-time operating systems. The USRP Software Defined Radio Stand-Alone Device enables you to prototype a range of advanced research applications such as stand-alone LTE or 802.11 device emulation; Medium Access Control (MAC) algorithm development; multiple input, multiple output (MIMO); heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
WLAN Test Toolkit -
NI
The WLAN Test Toolkit gives you direct and fine control over the generation and analysis of IEEE 802.11a/b/g/n/ac and ax signals, as well as 802.11j/p/ah/af waveforms, with industry-leading speed and accuracy. It empowers you to characterize, validate, and test a variety of WLAN connectivity products, such as RF front end components, wireless modules, and user devices.The toolkit includes extensive support for the latest features of the 802.11ax standard, including extended single-user packets, multiuser OFDMA, and multiuser multiple input, multiple output (MIMO) functionality with per-user configuration and measurement results. The WLAN Test Toolkit helps you solve demanding new access point test cases by generating signals that simulate multiuser environments, including per-user impairments. You can also use the new software to generate trigger frames to test the real-time response of client devices and make power precorrection and relative center frequency measurements.
-
TP500110 -
Total Phase Inc.
The Promira™ Serial Platform is our most advanced serial device ever. This new, powerful platform offers many benefits over our previous generation of host adapters:*Integrated level shifting ensures you'll be able to work at a variety of voltages ranging from 0.9 to 5.0 volts without needing any costly accessory boards.*High-speed USB connectivity to the host system provides high performance and convenience for benchtop programming, testing, and emulation.*Ethernet connectivity is convenient for benchtop work, and it also enables remote control for your automation needs.*With the ability to provide a total of 200 mA of power, Promira platform can easily power your project, simplifying connectivity and troubleshooting.*New architecture enables you to download applications to the Promira platform - Upgrade your device when you need new features and you'll never wait for that emergency delivery in the middle of your project.
-
Teledyne Marine Impulse-PDM
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with elastomers- Abrasion resistance- Stiffness profile at termination- Connector format (straight or right angle)- Molding format (straight or at an angle)- Clearance allowance for molding and cable routing- Elastomer compatibility (eg oil filled units)- Metalwork selection re: corrosion and cathodic delamination- Surface finish for metalwork as appropriateOperational considerations:- Operating depth profile (not just max. depth)- Tensile loads- Torsional loads- Bending loads- Bend control requirements (to limit bending at termination)- Deployment and recovery loads- Dynamic loading-Flow turbulence effects.
-
S-103 -
Notice
ASE broadband source slot module of FOTS system can offer special function that is able to change optical output spectral feature variously, which is change optical output spectral feature variously, which is followed by user’s driving embedded pump LD freely. The output power of each pump LD is controlled separately by the program that is set up by user. In the case optimum ASE source output features such as wide broadband (> 80 nm @ -10 dBm/nm) and stable output power (< 0.02 dB) is needed, it is made up so that the provided Default mode along with User mode can be chosen and set up. More stable application of ASE source is possible through the combination of monitoring of ASE output power, alarm status and pump LD status with real-time optimal feedback. The embedded FPGA processor makes high speed control possible and enables monitoring and feedback routine operated stably.
