Showing results: 631 - 639 of 639 items found.
-
Extech EX470A -
Extech Instruments Corporation
The Extech EX470A True RMS Multimeter and Infrared Thermometer with Capacitance, Frequency, and Duty Cycle Measurements and 2 K-Type Remote Probes is the perfect meter for HVAC or plant maintenance. The IR thermometer measures the surface temperature from -4 to 518 °F (-20 to 270 °C) without contact. The built-in laser pointer centers the measuring area. Multimeter functions include AC and DC Voltage to 600 Volt, AC and DC current to 10A, resistance to 40MOhm, continuity and diode test. Also includes Type K thermometer for contact or air temperature measurements from -4 to 1832 °F (-20 to 750 °C). Advanced functions include Capacitance, Frequency and Duty Cycle. The meter comes complete with test leads, Type K temperature probe, 9 Volt battery, protective holster, adjustable tilt stand and Velcro hanging strap.
-
Extech EX530 -
Extech Instruments Corporation
Ruggedly designed and waterproof to IP67 standards, the EX530 is ideal for use in the outdoors, on boats, and in any harsh industrial environment. It has a double molded housing and is drop-proof up to six feet with a safety rating of CAT IV 600 Volt and CAT III 1000 Volt. It measures AC/DC voltage and current, resistance, capacitance, electronic and electrical frequency, temperature, 4 to 20 mA, and duty cycle. Additional features include: 0.06% basic accuracy, continuity beeper, diode test (2.8 Volt open circuit voltage), 40000 count resolutions, backlit LCD with barograph, peak hold, min/max, relative mode, data hold and 1000 Volt input protection for all functions. Comes complete with double-molded test leads, type K bead wire temperature probe (-4 to 482 degrees F/-20 to 250 degrees C), magnetic hanging strap, case, and a 9v battery.
-
Teledyne Defense Electronics
The Emergency Interseat Sequencing System (EISS) was designed an qualified for the F-15K Fighter and has since been installed in the F-15SG and F-15SA configurations of the F-15. The system consists of Thermal Batteries with Initiators, a Digital Interseat Sequencer, Mode Selector, and customer provided cabling Electro-Explosive Devices (EEDs). The system is operated from either thermal battery and aircraft 28Vdc for redundancy. A separate field Test Set (EESSTS) performs both complete system continuity tests and an operational test of the total system installed in the aircraft. The sequencer is programmable and could be used in any escape system.Based on the initiation point, Forward or Aft Seat Handle, Internal or External Canopy Jettison Handles, and the Mode Selector setting, the Sequencer provides firing pulses to the EEDs to support canopy removal, ejection seat inertial reel activation(s) and ejection seat catapult firing(s). Sensing capabilities are provided to determine system state, canopy gone, seat gone, so as to provide the optimum escape timing.
-
SEN-30004-T03 -
Playing With Fusion Inc
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino.Each order comes with one board and a set of four female, long extension, headers that can be soldered to the board. If stacking two of these modules on top of each other, please order both a Ch 0-3 and a Ch 4-7 board, as well as an additional set of headers for stacking. We're working on sourcing even longer headers, but the ones currently available are not long enough to stack as-is (they need to be double-stacked).The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or MegaNote: we also offer a universal version of this board in a smaller for factor, the SEN-30003-T.FeaturesType-specific, miniature-sized vertical thermocouple connectors (vertical flat blades, see pics)Measures four (4) thermocouple channels, full extended range.Boards are stackable. Up to 8 thermocouple channels may be connected to an Arduino.14-bit SPI interfacePlugs directly into an Arduino Uno or Mega form factor with built-in voltage level translation on-board.Standard Arduino female headers required for easy configuration, one set included with order (1-6x1, 2-8x1, 1-10x1 0.1" female stackable headers), not soldered on.Detects shorts to GND or VccDetects open thermocoupleOther versions available (K, J, and T stocked). Contact Customer Service to place a custom order.Mounting holes for 4-40 sized screwsConnections are spaced for 0.1" pin headerDesigned, manufactured, tested and shipped from the USA The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
IBEKO Power AB
Making a product “safe” requires an understanding of “hazards” that exist in each electrical product. Electrical shock is one of the four fundamental hazards. Because of that, it must be a part of any product electrical safety evaluation. Even though a product requires an electrical power source and uses electrical or electronic components, it should not present an electrical shock hazard to the user.Ground bond or earth continuity testing prevents electrical shock hazards. Similarly to a fault to earth, test instruments generate a high current. The standard requires that the resistance between protective earth and any conductive surface on the equipment does not exceed 0,1 Ohm. The test is performed by applying a DC current between the conductive surface and protective earth. By measuring the voltage drop, it calculates the resistance.RMO-E instruments are ideal for testing the protective bonding (grounding) of equipment following the standard IEC 61010-1. Applying current up to the value of 100 A and the ability to provide in the Contin menu (continuous operation) test current for the pre-set test duration (equal or exceeding 1 min) gives a user a possibility to easily check the protective bonding/grounding of the equipment. The full load voltage of 12 V assures proper measurement and accurate result. Finally, an instrument displays pass/fail classification according to user-preset parameters.
-
MPI-525 -
Sonel S.A.
Possible measurementsShort-circuit loop measurement:*impedance measurement with 23 A current (44 A phase-to-phase) - short-circuit resistor R=10,*measurement range: 95...440 V, frequency 45...65 Hz,Short-circuit loop measurement with resolution 0,01, in distribution network without tiggering RCD (In30 mA):*automatic calculation of short-circuit, detection of phase voltage and phase-to-phase voltage,*additional UNI-Schuko plug for automatic measurement, AGT adapter for 3 phase network measurement.Testing of general and selective RCD with the rated differential current of 10,30,100,300,500 and 1000 mA. (Type AC, A and B).Measurement of insulation resistance:*with test voltage 250 V, 500 V, 1000 V, 2500 V,*measurement range up to 10G,*automatic discharging after measurement,*automatic measurement of all resistences in 3,4,5-wire cables using optional adapter AUTO-ISO,*acoustic signals in 5 sec intervals for insulation resistance characteristic,*elapsing T1, T2, T3 times (0...600 s) form measurement of absorption coefficients (DAR, PI or Ab1, Ab2)*safety measurement - protection against overvoltage.Measurement of earthing resistance.Bi-directional testing of PE wire continuity using 200 mA current.*Autocalibration of test leads.
-
CAMI Research Inc. (CableEye®)
A USB Type-C test interface board for CableEye® cable and harness testing systems. Consisting of a daughter board, populated with two USB-C female connectors, it allows users to continuity-check USB Type-C terminated cables using the CableEye tester while seeing the connectors-under-test rendered graphically. The CB26U fits all CableEye models. Configuration A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test. Sold as a set of two boards, each CB26U accepts two USB Type-C connectors. In addition to the latest CableEye software, it requires the CB26 small-frame motherboard (Item 756) for operation, and plugs into one of two available slots – two USB-C-connectors can be tested simultaneously. The CB26 (with CB26U) attaches to the tester like a regular connector board. Contact sales@camiresearch.com or +1 (978) 266-2655 for a quote.
-
PK-2030/2032/2033/2036/2037/2038 -
Pansco, Ltd
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
CableEye M2Z, M3Z, M4 -
CAMI Research Inc. (CableEye®)
Fast ● Simple ● Precise Advanced wiring analyzer scans for continuity (opens, shorts), miswires, resistance, capacitance, components (resistors, diodes, LEDs, capacitors), insulation resistance, intermittent connections. For diagnostic and Pass/Fail Testing All CableEye® testers are suitable for production, fault diagnosis, QC (Quality Control), assembly, and prototyping of standard or custom cables. Each combines test, fault location, design, documentation, labeling, and database storage in one instrument. Tests can be performed on long cables (with or without connectors) or no cables (e.g. connectors, backplanes, PCBs, components). Standard Features & Benefits:
- USB certified, PC-based tester for a versatile, fast, robust system with long life-cycle.
- Multilingual, dynamic, graphic-rich display (netlist & wiring schematic) provides clarity and speeds diagnostics.
- 128 Test Points, expandable to 1024 providing flexibility as your product line changes.
- Real-time screening for intermittent connections for pinpointing elusive faults and improving quality.
- Automation scripting in a simple, intuitive language allowing non-programmers to reduce operator error by automating repetitive steps.
- Pop-Up Work Instructions. choose the exact amount of detail, imagery, language and automation you need to ensure your work instructions and tests are carried out flawlessly.
- Flexible tolerancing: optionally define as percentages or absolute terms, as well as asymmetrically (e.g. +0%/-10%) for improved yields.
- Barcode-tracking & archival data-logging to achieve error-proof test process and improved traceability & productivity.
- Print PASS/FAIL labels, test reports (with or without color wiring schematics/netlists) and log reports to satisfy ISO9000 reporting requirements.
- Compatible with laptop and touchscreen PCs for fieldwork and rack/off-bench mounting.
Includes: CB15C board set (Item 745C) for common computer and peripheral device cables; comprehensive PC software with Database of >200 standard cables; 2 yr Product Support Subscription comprising Warranty, free tech support, and free software upgrades.
Select Add-On Options: Hardware: 128-point Expansion Modules (attach to base); Environmental Sensor Software:
PinMap™ fixture editor,
Connector Designer™ connector editor, or
Autobuild™ guided assembly modules camiresearch.com |@CAMI_CableEye |+1.978.266.2655
