Showing results: 496 - 510 of 931 items found.
-
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in chamber for Complex Salt Spray Test Relevant standards requirement1. Test Object: battery pack andsystem.2. Refer GB/T4 part 5.5.2 test method, test according to GT/T2423.17 test conditions.3. The salt solution was made up with sodium chloride (chemically pure and analytically pure) and distilled or deionized water,Its concentration is (5 + 1)% (mass fraction).4. (35 ± 2) ℃, the measured pH value is between 6.5-7.2.5. Placed the test objects in the salt spray chamber for cycling test. Each cycling duration for 24h. Spray salt solution to the test object for 8 hours under the temperature of (35± 2) ℃ , remain for 16 hours. Between the forth and the fifth hour in one cycles should be according to test requirement in GB/T 28046.1-2011, test mode with 3.2.6. Total 6 cycles testing.7. Salt spray test is not necessary for the test objects being installed in passenger, luggage or cargo compartments.
-
KWB-225 -
Shenzhen Chuangxin Instruments Co., Ltd.
Fast change rate temperature testing chamber simulates the changed environment of test temperature with rapid change rate based on linear or non linear, which is used to detect the resistance ability of electronic, automobile, rubber, plastics, aerospace science and technology, military technology and advanced communication equipment and other products in the heat and cold condition, so as to judge the reliability and stability for the products, improve the products quality and provide the basis for the reliability
-
-
-
MKS Instruments
The Process Sense endpoint sensor is a small, low-cost SiF4 sensor specifically designed for Remote Plasma Chamber Clean Endpoint detection for silicon-based CVD deposition chambers. Process Sense is based on infrared absorption, the only technique applicable to all plasma cleaning processes (in-situ and remote). It gets mounted onto a bypass on the rough line, ensuring no effect on deposition hardware. The signal level reported by the Process Sense, which is proportional to SiF4 concentration, can be used to determine the completion of the chamber clean process.
-
IR-400 -
HORIBA, Ltd.
The IR-400 offers real-time monitoring of the chamber cleaning end point during the deposition process. By optimizing the cleaning process, the IR-400 reduces cleaning time and gas usage. This reduction in cleaning gas usage leads to a reduction in chamber damage and increases the life times of all the systems components.
-
CX-IP9K -
Shenzhen Chuangxin Instruments Co., Ltd.
Water Spray Test Equipment is used to test the water resistance; which is mainly for electronic and electrical products. It can also provide references for product design and quality control.
-
Shenzhen Chuangxin Instruments Co., Ltd.
Steam aging test machine is used to test and determine the parameters, performance of electrical, electronics, other products and materials for high temperature, low temperature, or the temperature of the thermostat test environmental changes.
-
EV 2.0 Series -
HORIBA, Ltd.
To address new requirements in Semiconductor, lighting devices, automotive components, flat panels, MEMS sensors, memory chips, and logic electronics processed in the industry using dry etch, cleaning and (PE)CVD, HORIBA has introduced a unique generation of sensor dedicated to Advanced Endpoint Control, Fault Detection and Chamber Health Monitoring.
-
Shenzhen Chuangxin Instruments Co., Ltd.
This machine can test various materials (both finished and semi-finished products ) of tensile strength ,compressive strength and elongation ,can do stripping ,tear strength ,flexural ,compression test and etc. It can connect up to the computer and display or printout the test times , test value , max. value , etc . Also it can make various report forms according to the requirements .
-
8801HT/9801HT -
Hydraulic Technology, Inc.
The 8801HT retrofit safety test chamber kit is designed specifically for existing 8801-8801B and 9801B hydrostatic hose test systems in the field. It may also be ordered complete with a new 8801B or 9801B tester.
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's newly battery washing tester consisting of test chamber and washing chamber under test chamber. Moreover, it motorized rotary propeller mounted inside of test chamber and on internal wall of test chamber, drying system is mounted.
-
Gaynes Labs, Inc.
Large Walk-in Environmental Chamber, and Walk-in Salt Fog Chamber, various sizes of vibration and shock equipment, and environmental chambers.
-
Cincinnati Sub-Zero Products
CSZ chamber is designed for this type of cold bend test. Each chamber is designed to meet the customer's size and temperature requirements. Chambers feature power-driven mandrels that are typically mounted at the top and bottom of the chamber for the wire to wrap and bend around. Mandrel diameters are selected by the customer and supplied in a variety of sizes.
-
FS Series -
Darwin Chambers Company
The Darwin Chambers Stability Freezer FS Series is a top selling stability freezer chamber very common in laboratories.