Filter Results By:

Products

Applications

Manufacturers

Showing results: 391 - 405 of 2966 items found.

  • XMC Mezzanine Processor Card

    XMC-528 - Curtiss-Wright Defense Solutions

    The XMC-528 is a high-performance, user-programmable processing and FPGA resource for embedded security applications or use as an FPGA co-processing engine.

  • Multiplexed- Low-Level Function Card

    Neff Instrument Corporation

    Low-level multiplexed systems have a single programmable gain, wide-band amplifier following the input multiplexer. To accommodate low-level signal signals such as those from strain gauges or thermocouples and at the same time high level signals from other sources, the throughput rate must be limited to enable the high bandwidth amplifier to settle to the correct value after switching to a new channel. This results in a relatively low aggregate throughput rate when compared to an amplifier-per-channel system. A major benefit of a well designed low-level multiplexed system is the extremely high performance/cost relationship.

  • Wideband Amplifier PXI Card

    GX1222 - Terotest Systems Ltd.

    The GX1222 is a 3U single-slot, PXI-based wideband power amplifier used for signal amplification purposes. Offering excellent fidelity, the GX1222 amplifies signals from DC to over 20 MHz with a fixed gain of x10. Custom gains are also available without compromising signal purity and amplifier performance.

  • 10 Gigabit Ethernet Card

    TTC ETG-302-1 - Curtiss-Wright Defense Solutions

    The ETG-302-1 is a two-channel optical 10 Gigabit Ethernet board for the next generation Airborne Instrumentation Multiplexer, AIM-200XE-1. It receives and formats inbound (acquired) data. When the ETG-302-1 is used in the AIM, it can transmit data to an nREC-7000-1 recorder through one or two 10 Gb Ethernet ports.

  • 3 Port cPCI Card

    GX3903 - Terotest Systems Ltd.

    The GX3903 is a 3-port, cPCI asynchronous communications interface board supporting RS232 and RS422 levels. Optionally, the board can support RS485 signaling. Each port is configured at the time of order for RS232, RS422 or RS485 signaling. The default configuration is RS232. For RS232 mode, each port supports RTS, CTS, TXD, RXD, DCD, DRC, DSR, and RI signaling. The RS422 mode supports TXD, RXD, CTS, and RTS with each line operating differentially with a uni-directional drive.

  • 3U VPX Processor Card

    VPX3-1260 - Curtiss-Wright Defense Solutions

    Optimal for high performance embedded computing (HPEC), general processing, and a variety of C5ISR applications, the VPX3-1260 rugged single board computer (SBC) delivers a fully-featured, all-in-one processing solution for your embedded system.

  • 4 Port cPCI Card

    GX3904 - Terotest Systems Ltd.

    The GX3904 is an 8-port, cPCI asynchronous communications interface board supporting (4) RS232 and (4) RS422 signal levels. The four RS232 ports offer a full set of data and modem control lines configured for DTE operation. The four RS422 ports offer differential signaling and support DTE operation. Each RS422 differential pair is terminated by a 150 Ω parallel resistor. An optional transition cable is available to convert the front panel SCSI connector to (8) DB-9, D-sub connectors.

  • 6-bit Data Acquisition Card

    DAP 5216a - Microstar Laboratories, Inc.

    The DAP 5216a model adds 16-bit resolution to the proven capabilities of the DAP 5200a line. It has the same real-time processing power as the DAP 5200a. Real-time processing functions include smoothing, filtering, FFT, PID control, and responding to alarm conditions; the DAP 5216a also can scan high-speed data for trigger events in real time to capture pre-trigger as well as post-trigger data.

  • ARINC PCI Interface Card

    PCI-A429 - Alta Data Technologies LLC

    Alta Data Technologies’ PCI-A429 interface module offers a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal.

  • Audio Card I/O Modules

    PIM481-J/DSUB - AcQ Inducom

    The PIM481-J PMC I/O Module, with four 3.5mm stereo connectors and the PIM481-DSUB PMC I/O Module, with D-sub for rear I/O can be mounted on a rear transition module (RTM).

  • ROM Emulator PXI Card

    NX5000 Series - Marvin Test Solutions, Inc.

    ROM emulation is a powerful and versatile method of microprocessor testing. ROM emulation has emerged as the technique of choice for microprocessor test and diagnostic applications. A microprocessor-based board is tested by replacing the boot ROMs on the Unit Under Test (UUT) with memory emulation pods. Each pod handles eight bits of the data bus. Processors from 8 to 32 bits can be controlled with one to four pods (even the most advanced CPUs such as the Intel Pentium generally use only an eight-bit boot path). The emulator takes control of the UUT by resetting the processor and, under the test program’s control (monitor program), exercises all functions on the board. Synchronization with the UUT is automatic and requires no additional hardware or connections.

  • Digital I/O PXI Card

    GX5290 - Terotest Systems Ltd.

    The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.

  • Digital I/O PXI Card

    GX5150 - Terotest Systems Ltd.

    The GX5150 Series are high speed, 6U PXI, sequenced digital I/O instruments. The GX5150 master controller has 32 bits of I/O channels that supports test rates of up to 50 MHz and a vector depth of up to 128 Mb per pin. The GX5151 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5150. The GX5150 can control up to 15 GX5151 boards using the same timing and sequencer.

  • Digital I/O PXI Card

    GX5280 - Terotest Systems Ltd.

    The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.

  • 6U OpenVPX Processor Card

    CHAMP-WB - Curtiss-Wright Defense Solutions

    Integrating FPGAs into any system can be challenging: from ensuring your boards will meet your performance needs in the most rugged conditions to creating a basic framework that will last despite growing radar system, EW & SIGINT application needs. Taking advantage of tested and proven resources can help you speed development and guarantee your boards are ready for anything.

Get Help