Showing results: 4651 - 4665 of 5238 items found.
-
WDM -
IXI Technology
It is highly desirable to reduce the number of cables required to communicate between spaces on Navy ships due to increased weight, cost and maintenance concerns. To reduce weight and expense, copper-based NTDS parallel and serial type cables can be converted to fiber optic and multiplexed using Wavelength Division Multiplexing (WDM) technology. WDM technology allows for multiple fiber optic wavelengths to be combined in a single fiber and then separated back to individual fibers at the distant end. Using Coarse WDM (CWDM) which utilizes wavelengths 20nm apart ranging from 1271 nm to 1611 nm, provides for up to 18 optical wavelengths to be combined into a single fiber. Optionally Dense WDM (DWDM) can be used allowing for up to 160 optical wavelengths.
-
RJ45 -
Aegis Pty. Ltd.
This easy to operate LAN tester enables you to test your wiring and connections at installation or after maintenance, making it one of the most convenient tools on the market. With the press of a single button you can automatically run a barrage of tests, including tests for Continuity, Opens, Shorts, Crosses and Splits. You can also identify which pairs require correction; The unit will scan all combinations without you having to do anything other than initiate the test. Even cable shield is tested for continuity! Building on the features provided by other testers such as the CZ20250, this LAN tester will also test coax networks and provide a tracing tone for cable identification. And it tests for all these at lightning speed, saving you as much time as possible.
-
Sciencetech, Inc.
The Solar Reference Cell consist of a 20 x 20 mm monocrystalline silicon Photovoltaic Cell encased in a 92 x 70 x 16 mm metal enclosure with a protective quartz window and a temperature sensor. The temperature sensor is a 100 ohm platinum Resistance Temperature Detector (RTD).The Solar Reference Cells come with a Certificate of Calibration and compatible set of connecting cables. The following parameters of the reference cell are certified: Isc, Imax, Voc, Vmax, Pmax, Area, Fill Factor and Efficiency. The certification is accredited by NIST to the ISO-17025 standard and is traceable both to the National Renewable Energy Laboratory (NREL), and to the International System of Units (SI). A compatible cable set is also supplied with each Solar Reference Cell.
-
RCT1A and RCT5A -
Powertek LLC
These probes have great bandwidth ensuring accurate measurement even with harmonically distorted wave shapes. For all RCT1A/RCT models, a NIST, NAVLAP, NPL (UKAS) factory traceable calibration certificate and certificate of conformance is supplied. UL/CSA approved materials are used throughout. Three phase and single phase flexible AC current sensors (rope sensors) are available for fast installation in confined spaces, eliminating the need for Electrical Supply Shutdown. Available outputs are 1A @ 2.5VA and 5A @ 0.5VA, this means long cable lengths from current sensor to signal conditioner allow these low VA ratings to be used, even when feeder cable to energy meter distances are large (up to 98 feet / 30 meters)
-
Analog Devices Inc.
Analog Devices HDMI® switches and DVI switches, as well as buffers, empower designers to easily expand the number of HDMI inputs in their systems. Advanced equalizer technology enables the connection of 1080p deep color HD equipment over more than 20 meters of cable with our HDMI switches and DVI switches. We offer the industry’s broadest selection of buffered HDMI multiplexers, with applications including HDTV, set-top boxes, A/V receivers, projectors, and other multiple input displays. Low jitter equalizer technology enables a single equalizer setting for all cable lengths from 0 meters to >40 meters. Analog Devices HDMI/DVI switches enable customers to meet many challenging system requirements.
-
PM-102B -
SYOPTEK INTERNATIONAL LIMITED
The PM Series Optical Power Meter are designed for use with an Optical Source for performing optical loss measurements on fiber optic cables. The PM-102 series are designed for affordable budgest, but meet the basic demands for real world testing. With a smaller size and weight, it’s easy to take these units into any enviroment.
-
PM-102A -
SYOPTEK INTERNATIONAL LIMITED
The PM Series Optical Power Meter are designed for use with an Optical Source for performing optical loss measurements on fiber optic cables. The PM-102 series are designed for affordable budgest, but meet the basic demands for real world testing. With a smaller size and weight, it’s easy to take these units into any enviroment.
-
6034 -
Associated Equipment Corp.
• Carbon pile tester handles all 6/12 volt batteries• Two large 4.5″ analog meters display amps and volts• DC test leads are 2.5′ 4 AWG cable• Unit comes with manual adjust knob• Buzzer sounds after load is engaged for 15 seconds• Imported
-
SS71XX series -
Sanshine Electronis Co., Ltd.
High voltage withstand and insulation tester (HI-POT tester) is used for testing insulation grade and withstanding voltage capability of electrical equipment, transformers, motor, relays, cables, electronic components, electronic applications, inductors, ignition coils, insulation wires, insulation tapes, valve coils, reactors, contactors, etc.
-
BD-POW-2A09 -
Shanghai Baudcom Communication Device Co.,Ltd.
BD-POW-2A09 is the companyhighly cost-effective optical multimeter. It’s the integration of power meterand light source. BD-POW-2A09 has the function of recording, storing anduploading the data tested by the instrument. They are widely used in thefiber-optic line project construction, testing and maintenance, such as digitaldata network, telecommunication network and cable television.
-
Mitsubishi Electric Automation, Inc
Measuring display units (MDU) are integrated with molded-case circuit breakers and earth leakage circuit breakers for measuring, displaying, and transmitting information on cable ways. This display unit closely monitors energy consumption by measuring current, voltage, power, electric energy, harmonic current, leakage current and power factor.
-
Nitro -
Viavi Solutions Inc.
The VIAVI Network Integrated Test, Real-time analytics and Optimization (NITRO) solution is the first real-time intelligence platform that connects testing and service activation data from instruments with software-based planning, provisioning, assurance and optimization probes and applications, working seamlessly across mobile, fiber, cable, cloud and enterprise networks.
-
STC-OLS201 series -
Shanghai Stone Communication tech Co., Ltd
a simple and cost-effective fiber optic tester,it is usually used together with fiber optic power meter to measure the optical loss on fiber cables. STC-OLS201 series light source provide multiple wavelength output, the wavelengths can be required on customer specific requirements (the Max wavelength is 5, such as 850/1300/1310/1490/1550nm).
-
60-310-302 -
Pickering Interfaces Ltd.
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
60-310-202 -
Pickering Interfaces Ltd.
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
