Showing results: 1 - 15 of 40 items found.
-
TBOH01 -
TekBox Singapore Pte. Ltd.
The TBOH01 5H LISN is a device required to setup conducted noise measurements of DC-powered devices. It is designed to be used for EMC pre-testing in the frequency range of 150kHz to 110 MHz.
-
ALSE -
Seibersdorf Labor GmbH
Due to on-going work in the standardization committee CISPR D (responsible for CISPR 25) the latest issue CISPR 25 Ed. 4.0 has not been cited to-date. In the meantime we are able to offer two different validation procedures:
-
AFJ Instruments
AFJ receivers and accessories for the disturbance power using the absorbing clamp measurement, are conforming to CISPR 16-1-1 and CISPR 14-1.
-
ISN -
Com-Power Corporation
They are required for the measurement of conducted common mode noise on Telecom Cables of Information Technology Equipment (ITE). These measurements are necessary to meet the requirements specified in CISPR 22 and CISPR 32 standards.
-
AL-130R -
Com-Power Corporation
Also known as Magnetic Loop Antenna, the AL-130R is compliant with CISPR 16-1-4. It is ideal for emissions measurements as required by various EMC standards such as FCC 18, CISPR 11, CISPR 13, CISPR 14, CISPR 32 and many more. The built-in, low-noise preamplifier, increases overall measurement sensitivity as well as the overall signal to noise ratio. As per ANSI C63.4-2014, the use of active loop antenna for compliance testing is permitted in a non-sheilded environment ONLY if the saturation indicator is continuously monitored during the course of testing. Com-Power’s Remote Antenna Interface (RAI-100) comes in very handy for this application. It is a compact controller which can be used to enable/ disable RF measurement circuit and monitor saturation and battery low conditions remotely via a fiber optic cable up to 30 mtrs in length.
-
Ambient Noise -
Seibersdorf Labor GmbH
The Ambient Noise (AN) measurement is done in accordance with CISPR 22 and EN 50022
-
-
AFJ Instruments
High accuracy CISPR 16-1-1 EMI receivers and high precision calibrated antennas for radiated emission measurements.
-
-
Table Influence (TI) -
Seibersdorf Labor GmbH
The Table Influence (TI) is measured according to CISPR 16-1-4 in the frequency range 200 MHz 18 GHz.
-
NSA -
Seibersdorf Labor GmbH
Normalised Site Attenuation (NSA) is measured in accordance with CISPR 16-1-4 and ANSI C63.4 in semi and fully anechoic environment.
-
Schwarzbeck Mess Elektronik
Antenna Impedance converter acc. CISPR 25 9 kHz - 30 (120) MHz.Option ACS 110: Charger ACS 110 for VHIC 9260
-
Com-Power Corporation
Biconical antennas are used for emissions and immunity testing to meet various EMC standards specified by FCC, CISPR and EN. The broadband characteristics of the biconical antenna make it a good choice for making sweep measurements and for automated measurement systems.
-
Parker Hannifin Corp.
Parker Chomerics offers a wide variety of EMI/EMC and safety testing for regulatory compliance. Tests include FCC, EC, VCCI, IEC 1000 (formally 801) EN 61000 Series, CISPR, Austel, MIL-STD-461 and EU regulations
-
Schwarzbeck Mess Elektronik
Calibration-Pulse Generatoracc. CISPR 16for Band A, B, C, D(9 kHz-1000 MHz)To calibrate the pulseresponse of EMI receivers.Pulse repetition frequency main generator 0.1 - 200 Hz (aux. generator up to 1 MHz) with IEEE-488 Interface.
