Showing results: 76 - 90 of 173 items found.
-
Certifier 1200 -
LITE-CHECK LLC.
Presenting a vehicle test station for electrical, brake, and ABS End-Of-The-Line testing from LITE-CHECK, the leader in economical, technician-friendly test equipment. With state of the art software and hardware automatic operations are recorded for a complete printed report of the vehicles electrical and air system. Heavy-duty test station for complete electrical, air brake, ABS, and 121 brake timing & end-of-line testing.
-
Van Leeuwen Test Systems BV
In case vehicles need to perform a brake test in laden condition, one could consider to use a load simulator. In that case the vehicles can come to the brake test unladen; the load simulator will add the required load to the axles.
-
-
AP-GB/2.10 -
STAHLE Robot Systems
Actuator for precise operation of accelerator and brake pedal in vehicles.
-
Magtrol Inc.
The most important characteristic of any measurement instrument is repeatability and accuracy. The Magtrol Dial Weight Dynamometer uses the combination of a Hysteresis Brake and gravity to insure constant, reliable results. The brake torque rise is directly proportional to applied current
-
EBS301 -
Autel
The MaxiService EBS301 Electric Brake Service Tool is specially designed for safe and professional replacement of brake pads on an increasing number of modern vehicles. Connecting to the vehicle’s OBDII socket, this tool automatically links up with the control module. Disengaging the brake system, it increases safety with the push of a button. Eliminating the needs to use expensive OEM diagnostic systems to do the job on electronic systems, the tool is a time saver and a money maker!
-
-
TT9102 -
Matco Tools
Commercial trailer light and electric brakes tester that reduces guesswork and saves time by powering each trailer electrical circuit in 7-way round pin arrangements. Allows for proper verification of wiring configuration, ground integrity, short circuit and overload conditions, along with electric brake operation and turn signal simulation.
-
Power Test, Inc.
Eddy current, Water brake and AC motoring chassis dynamometers for dyno testing heavy-duty on and off-highway vehicles.
-
MSR 500/2 CAR 4WD (ADD. BRAKE) | VP 230041 -
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD can also be extended with a 3rd or 4th eddy current brake.
-
AW Dynamometer, Inc.
Dynamometers come in four different models all using the same basic design - a hydraulic activated prony brake.
-
767943 -
Wesbar
Plug these testers into any car connector and you will have an instant test of running light circuits. Features LED display to show completed circuit for the running lights left turn signal and right turn signal. Auxiliary and electric brake circuit are included on the 6-way tester and auxiliary, electric brake and battery charge are included with the 7-way tester. One piece units with internal ground. Proper installation and set-up of a brake control, when a trailer is not readily available, is possible with the 7-way tester. Current Monitor testing device is designed to assist in determining whether a tow vehicle's 7-way blade car end connector has been wired properly. (Current Monitor is an excellent diagnostic tool for installation, setup and troubleshooting of electric trailer brake controls.) The Trailer Tester is designed to help you quickly identify problems in the wiring of the trailer. This is done by testing the Left Turn, Right Turn, Tail/Marker, Brake and Back Up circuits on the trailer. The tester indicates approximate amount of current in each circuit (i.e. trailer battery). Brake Control Bench Tester is a test device designed to determine if a brake control is working properly. Checks brake control output, independent of vehicle wiring. Simulates many fault conditions including open ground, short circuit, open load and more.
-
Power Test, Inc.
Electric Motor Test Systems feature our highly successful water brake dynamometer which is used as an electric motor loading device.
-
Checkmate 1200 -
Square Wheel Industries, Inc.
Checkmate 1200 is a good, basic light tester for trailer light systems that can also serve double duty to power anti-lock brake systems.
-
Power Test, Inc.
Water brake, Eddy current and AC dynamometer systems for heavy-duty diesel, gaseous and gasoline testing applications from 20 through 10,000 HP.