Filter Results By:

Products

Applications

Manufacturers

Showing results: 196 - 210 of 639 items found.

  • Density Tester

    LD-LDMT-A10 - Labodam

    LabodamLD-LDMT-A10density tester is simple and compact. The control box adopts humanized design and the control switch adopts light-touch mode. The instrument is designed and made as per ASTM D1298 “Test Methods for Density of Petroleum and Liquid Petroleum Products (Densimeter Methods).

  • Dial Indicators

    Rhopoint Metrology Ltd

    1. Always select the dial test indicator that best fits the application.2. Care should be taken while using a dial test indicator, try not to jolt the indicator, should you be unfortunate and drop a dial test indicator, get it re-calibrated/repaired before reusing it.3. Replace worn contact points only with those of a similar length from the centre of the ball stylus to the abutment shoulder.4. Always clean dial test indicators after use with a lint free paper or cloth and store the indicator in its box or in a dust free area.5. When using a dial test indicator, always position the dial test indicator in a horizontal plane to the surface media.6. Always use a rigid stand for mounting the dial test indicator.7. When measuring a rotating object, either between centres or in a vee block, ensure that the object is rotating in the correct direction. Never rotate the workpiece towards the contact point.8. When measuring a sliding object, only take readings when the object is moving directly towards the contact point, never away from the contact point or in a sideways manner.9. Avoid parallax errors by reading the dial directly from the front and square on to the dial.10. Never oil a dial test indicator as this attracts contamination, should the movement become erratic then the dial test indicator should be submitted to a reputable repair agent.11. Try not to expose dial test indicators to direct sunlight or in a high humidity environment.12. Never use a dial test indicator that has not been calibrated, if in doubt consult an appropriate authority.

  • Digital Interface

    DNTBOB-88 - Lectrosonics, Inc.

    BOB 88 is a high quality, general purpose interface to transmit and receive line level analog audio signals via a Dante network. Analog inputs are converted to digital and appear on the network as transmit channels. Audio for the analog outputs is taken from subscriptions to transmit channels on the network from other sources. When connected to a network, each break out box will appear as a separate device in the Dante Controller software interface.

  • Digital Signage Player

    Axiomtek Co., Ltd.

    Axiomtek's high performance digital signage box players are designed to support the latest Intel processors with integrated Intel HD Graphics to provide outstanding computing performance and superb full HD graphics capability. The entry-level signage box players are the surprisingly affordable, space saving, and superior graphics solutions. The fanless, compact chassis enhances reliability and enables the unit to easily fit into any space-limited environments.

  • DISCRETE TMTC INTERFACE BOX

    Temis S.r.l.

    The Discrete TM/TC Box is a 6U custom 19’’ rack equipment that could be filled with 6U, 4HP plug-ins covering the main ECSS compliant discrete I /Fs. The I/O signals of this box are all arranged in the rear side of the box, keeping clear the front side: in this way no accidental operation could be performed on the box.

  • DMX Break Out Box

    DMX-Break - Artistic Licence Asia Ltd

    DMX-Break™ is a 'Break Out Box' for DMX512. It is primarily intended for engineers and allows the pins of the DMX512 XLR connector to be individually isolated.

  • Dynamic X-Ray Detector

    Shad-o-Box HS - Teledyne DALSA

    The Shad-o-Box HS family of x-ray detectors are high-performance, high-resolution x-ray imaging devices designed for high speed digital radiography applications. Each model combines our x-ray sensor modules with appropriate readout electronics and a 14-bit digital interface for easy connection to a PC. The high-speed digital connection allows real-time imaging at frame rates up to 66 fps, while the state-of-the-art CMOS technology offers superb contrast, dynamic range, and resolution.

  • ELECTRICAL LOAD BOX

    Temis S.r.l.

    The Electrical Load Box LOADS in charge to simulate the typical consumption of electronics’ equipment.The Box is a 5U, 19’’ modular rackable equipment that can house up to 50 resistors mechanically and thermally attached to two high efficiency heat-sinks, with integrated fans, for each boxTesting points for current and voltage measurement are provided as well

  • ELOS Box 54 Without Ventilation Slots (ELOS-E1)

    125106 - ELMA Electronic, Inc.

    The box is an embedded enclosure for 2 to 3 controller cards. It consists of an aluminum profile and it is especially developed for industrial applications. It can be equipped with a corresponding backplane as well as a suitable power supply.

  • EZ-Glider Position Control Telescoping Torque Arms

    Mountz Inc.

    The position control telescoping torque arms help manufacturers detect and eliminate costly screw-fastening errors during the assembly process. Position Control telescoping torque arms are designed to reduce the risk of improperly fastened screws, ensuring that every screw is in the correctly tightened in the correct sequence. Using the EZ-Glider Position Control torque arm is like putting the eyes and ears of a quality control manager where they are needed most - right on the assembly area.The EZ-Glider Position Control telescoping torque arm consists of a torque reaction arm with encoders mounted at the base and a control box. The control box is used for programming and it tracks the axis movement by converting angle counts to the precise position of the screwdriver. The location is calculated from encoder values, allowing the operator to easily teach the torque arm a programmed sequence pattern and then use it to control the assembly process

  • Fanless Robotic Controller with Intel® Xeon®/Core™ Processor

    ROScube-I - ADLINK Technology Inc.

    ADLINK ROScube-I is a real-time ROS 2 enabled robotic controller based on Intel® Xeon® 9th Gen Intel® Core™ i7/i3 and 8th Gen Intel® Core™ i5 processors featuring exceptional I/O connectivity supporting a wide variety of sensors and actuators for unlimited robotic applications. Also supported are Intel® VPU and NVIDIA GPU cards for computation of AI algorithms and inference. The extension box allows for convenient functional and performance expansion. ROScube-I supports the full complement of resources developed with ADLINK Neuron SDK, a perfect platform for development of industrial use service robotic applications such as autonomous mobile robots (AMR) and autonomous mobile industrial robots (AMIR).

  • Femtosecond Ti:sapphire Laser Kits

    TISSA Series - CDP Systems Corp.

    TISSA kits contain all components of femtosecond Ti: sapphire oscillator preinstalled and tested on a breadboard and supplied with a cover box.

  • Fiber \ Cleaver

    OFC-10CT - ShinewayTech

    ◆ High precision preparation for single fiber◆ Compact & handy outfit design◆ Rugged body◆ Simplified blade adjustment & replacement◆ Collecting fiber box

  • Fifo Serial Analyzer 2 TO 2 Breakout Box

    FLL222 - Fifo Electronics

    The FLL222 Break Out Box is designed to be used with the FLL and FSA serial analyzers to monitor full duplex bidirectional data. The serial line passes through FLL222 using the 9-pin connectors on the unit. Data from pin 2 of the serial line is available on pin 2 in the first output cable. Pin 3 data is available on pin 2 of the second cable. The output cables can be plugged into the COM ports of the PC running the serial analyzer.

  • Fifo Serial Analyzer Breakout Box

    FLLBOB - Fifo Electronics

    FLL BreakOut Box FLLBOB is a breakout box specially designed to be used with the FLL and FSA serial analyzers. With FLLBOB it is easy to connect the PC to the serial line without having to make dedicated cables.

Get Help