Showing product results. 2866 - 2880 of 3935 products found.
-
EM-6869 | 9 KHz – 50 MHz - Electro-Metrics Corp.
The Electro-Metrics EM-6869 Active Loop Antenna is used with any receiver or spectrum analyzer with 50 ohm input and covers the frequency range of 9 kHz to 50 MHz.
-
EM-6876 | 9 KHz – 30 MHz - Electro-Metrics Corp.
The Electro-Metrics EM-6876 Active Loop Antenna is used with EMI Receivers and Spectrum Analyzers with 50 ohm input and covers the frequency range of 9 kHz to 30 MHz.
-
TDR9100 - Manta Test Systems
The Doble TDR9100 Circuit Breaker Analyzer is a state-of-the-art circuit breaker test set for testing all types of circuit breakers with efficient and accurate performance measurements.
-
Navigator AW641 - ABB Ltd.
ABB's Navigator 600 Silica analyzer substantially cuts the costs and maintenance associated with silica monitoring in power generation and other large-scale steam and water dependent applications.
-
Ametek Materials Analysis Division
Our analytical systems include elemental analysis systems for bulk, micro and nanoscale applications as well as structural analysis & visualization systems and energy storage and test analyzers.
-
CloudSDR - RFSPACE, Inc.
The CloudSDR''s remote mode also offers a variable width spectrum analyzer with adjustable spans up to 10 MHz wide. The spectrum information update rate can be adjusted up to 10 Hz or turned off to limit the bandwidth utilization. In addition, the built-in squelch can be used to limit data transmission when no signals are present. Wideband spectrum analyzer mode offers 56 MHz wide spectral captures in both 2D, 3D and waterfall formats.
-
B-Smart - Bacharach, Inc.
Bacharach’s B-Smart sensors allow for easy field-replacement with a pre-calibrated sensor. Eliminate the need to send your equipment in for annual calibration, and always have your analyzer reading accurately and ready to go. Just snap in your sensor, enter the B-Smart code displayed on the sensor label, and get back to work. Each B-Smart sensor comes with a certificate of calibration for your internal compliance recordkeeping, giving you the confidence that your analyzer is accurate every time.
-
Keysight Technologies
These smart mixers use a simple USB plug-and-play connection which can automatically configure the signal analyzer for the specific mixer connected, including downloading conversion loss data and automatically compensate for local oscillator path loss. Therefore, it provides you with the most efficient test setup, shortening the overall start up operations with better performance with its embedded smart features when used with Keysight EXA, PXA, MXA, and UXA signal analyzers.
-
M+P International
m+p Analyzer systems are available for field and laboratory use from 4 to many hundreds of measurement channels. From gathering simple time history data to narrowband (FFT) spectra, fractional octaves, wavelets, shock response spectra and much more, m+p Analyzer real time analyzers can be used with a wide range of instrumentation hardware including our own m+p VibPilot, m+p VibRunner and m+p VibMobile systems, National Instruments (CompactDAQ USB, PCI, PXI) and VTI Instruments (PCI). Low cost portable instruments to systems for distributed measurements can be configured for maximum flexibility. Measurement data from all sources are stored in a common format so it is easy to compare and handle results from any measurement source.
-
ACM2520 - Copper Mountain Technologies
ACM2520 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 20 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full 2-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to 18 connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
ACM4509 - Copper Mountain Technologies
ACM4509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full four-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to 18 connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
ACM2509 - Copper Mountain Technologies
ACM2509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full two-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to seven connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
KEOLABS sas
Laboratory class spy and protocol analyzer for easy, non-intrusive capture and analysis of communication between contact cards and readers using SWP, ISO 7816, SPI and I2C protocols.
-
TDK SolidGear Corporation
Bus Extender is a bus extension device for observing the waveform of the bus signals between MicroSD card compatible devices (such as mobile terminals) and the MicroSD card using a logic analyzer.
-
Keysight Technologies
The Keysight 346, 347 and SNS Series of noise sources work in conjunction with the NFA Series noise-figure analyzers to make noise-figure measurements from 10 MHz to 50 GHz.