Showing results: 166 - 180 of 501 items found.
-
NES-FMC4ADC -
Sundance Multiprocessor Technology Ltd.
By default this card only uses signals from the LPC rows of the HPC connector that is mounted. The gain can be set by software in three steps: +/-50mV, +/-0.5mV, and +/-5V. AN advanced offset circuit is used in the front-end design of the ADC board, and allows a voltage shift in the range og +/-5V that is independent of the chosen gain range.
-
T3DSO1000 Series -
Teledyne LeCroy
Teledyne Test Tools new T3DSO1000 Oscilloscopes feature two channel and four channel models. The two channel model is available with 100 MHz, a single ADC with a 1 GSa/s maximum sample rate, and a single memory module with 14 Mpts of sample memory. The four channel scope is available in 100 and 200 MHz models and incorporates two 1 GSa/s ADCs and two 14 Mpts memory modules. When all channels are enabled, each channel has sample rate of 500 MSa/s and a standard record length of 7 Mpts. When only a single channel per ADC is active, the maximum sample rate is 1 GSa/s and the maximum record length is 14 Mpts. For ease-of-use, the most commonly used functions can be accessed with its user-friendly front panel design.
-
784471-01 -
NI
28-Bit, 32-Channel, 2 MS/s, ±15 V Flexible Resolution PXI Analog Input Module—The PXIe-4309 samples up to 32 differential channels and multiplexes the analog input channels across eight simultaneously sampling ADCs. The module samples eight input channels up to 2 MS/s/ch (single channel per ADC), and 32 input channels up to 100 kS/s/ch (four channels per ADC). The module's flexible resolution ranges from 18 bits at 2 MS/s/ch to 28 bits at 2 S/s/ch. The module features on-board signal averaging and filtering, auto-zero measurement switching, and a chopping mode that uses a pair of channels to provide high levels of noise rejection and to enable accurate and repeatable nano-volt measurements.
-
FMC126 -
Abaco Systems Inc
The FMC126 is a quad-channel multi-mode A/D FMC, fully compliant with VITA 57.1 standards.The card provides four 10-bit ADC channels that enable simultaneous sampling of 4, 2, or 1 channel with a maximum sample rate of 1.25 GSPS (4-channel mode), 2.5 GSPS (2-channel mode), or 5.0 GSPS (1-channel mode).
-
Guzik Technical Enterprises
High performance and high speed digitizers with wide bandwidth and high dynamic range. Featuring high-speed Analog-to-Digital Converters (ADC) with Real-Time Field Programmable Gate Array (FPGA) based digital processors. Long acquisition memory coupled with fast PCIe offload and streaming over optical data interfaces (ODI).
-
FMC116 -
Abaco Systems Inc
The FMC116 is a 16-channel ADC FMC daughter card which is fully compliant with the VITA 57.1-2008 standard. The FMC116 provides 16 A/D 14-bit 125Msps channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available.
-
RTA4000 -
Rohde & Schwarz GmbH & Co. KG
Designed with top class signal integrity and responsive ultra-deep memory, the R&S®RTA4000 brings the power of 10 to a new level. The Rohde & Schwarz designed 10-bit ADC plus class-leading noise and memory depth provides sharp waveforms, more accurate measurements and confidence when facing unexpected measurement challenges.
-
Virtins Technology
Multi-Instrument is a powerful multi-function virtual instrument software. It is a professional tool for time, frequency and time-frequency domain analysis. It supports a variety of hardware ranging from sound cards which are available in almost all computers to proprietary ADC and DAC hardware such as NI DAQmx cards, VT DSOs, VT RTAs and so on. It consists of the following instruments and functions.
-
DP-VME-1427 -
Data Patterns Pvt. Ltd.
The DP-VME-1427 is a standard 6U VME based general purpose 32 channel Analog to Digital Convertor (ADC) module. The module is a slave VME 64x interface, that responds to A24/D16 standard VME address cycle. On-board auto-conversion circuitry performs all the task related to multiplexing, sampling and converting of analog input signals to the digital outputs.
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
The imaging ultrasonic testing systems of the USPC 30XX series are optimized for testing a wide variety of materials and provide high-resolution findings in the form of A, B, C, D and F images. The hardware consists of an industrial PC, in which a motor controller and an ADC card are installed, as well as a HILL-SCAN pulser/receiver unit. An overview of the available systems is given in Table 1.
-
FMC150 -
Abaco Systems Inc
The FMC150 is a dual channel ADC and dual channel DAC FMC daughter card. The card provides two 14-bit A/D channels and two 16-bit D/A channels which can be clocked by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition there is one trigger input for customized sampling control.
-
Curtiss-Wright Defense Solutions
Digital Down Conversion (DDC) FPGA IP cores are available supporting Xilinx Virtex-5, Virtex-6 and Virtex/Kintex-7 FPGAs. The DDC family of IP cores support decimation from 2 to 64 in complex mode and from 2 to 32 in real mode. The DDC is available as embedded IP within a number of Curtiss-Wright ADC products or in a source format.
-
ADC500-5 -
Sundance Multiprocessor Technology Ltd.
FMC-ADC500-5 is a High Pin Count (HPC) FMC module with 5 ADC channels each running at up to 500MS/s with a dynamic range of 16 bits. The module has 5 ADC31JB68 ICs from Texas Instruments together with an HMC7044 from ADI which is the source of clocks feeding the ADCs. Provision for external clock input is also provided for this hardware.
-
APE1553-x-DS -
AIM GmbH
A unique feature of AIM’s APE1553-x-DS modules is the option for the MILScope™ capability. Models APE1553-1-DS/APE1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
FMC-SDR400 -
Sundance Multiprocessor Technology Ltd.
FMC-SDR400 is a Dual RF multiple input/output module (MIMO) based on AD9361, 70MHz – 6GHz RF transceiver and AD9656 ADC for baseband sampling of less than 70MHz (input only in this range). A software selectable gain and tunable RF bandpass front-end section provides high RF sensitivity by allowing rejection of out-of-band-of-interest interfering signals.