-
product
C Series Counter Input Module
The C Series Counter Input Module features flexible, 32-bit counters. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal, switchable pull-up resistor. Additionally, you can use the C Series Counter Input Module to perform encoder position and velocity measurements as well as to synchronize the counters with other analog, digital, and counter measurements in your chassis.The C Series Counter Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
NI-9482, 4-Channel, SPST Relay, 60 VDC (1 A)/250 VAC (1.5 A) C Series Relay Output Module
782999-01
The NI‑9482 directly connects to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to an electromechanical relay for switching signals up to 60 VDC (1 A) or 250 Vrms (1.5 A), features channel‑to‑channel isolation, and has a LED that indicates the status. The shock and vibration rating for the NI‑9482 is limited compared with other CompactDAQ and CompactRIO modules because of the mechanical relays on the module.
-
product
PC/104 Input/Output Module
PCM-UIO48C-16
The PCM-UIO48C-16 is a highly versatile PC/104 input/output module providing 48 lines of digital I/O. The major feature of this card is its ability to monitor 24 lines for both rising and falling digital edge transitions, latch them, and then interrupt the host processor notifying that a change-of-input status has occurred. This is an efficient way of signaling the CPU of real-time events without the burden of polling the digital I/O points.
-
product
C Series Voltage Output Module
The C Series Voltage Output Module helps you update analog output models that feature overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST-traceable calibration. This module includes up to 16 channels. Some models include a channel-to-earth ground double isolation barrier for safety and noise immunity as well as improved signal quality, and some higher density models conserve chassis space, which leaves room for other measurement types.The C Series Voltage Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
C Series Frequency Input Module
The C Series Frequency Input Module is designed to acquire isolated frequency inputs from magnetic pickup sensors, variable reluctance sensors, Hall effect sensors, and other transducers with a frequency output. Additionally, the C Series Frequency Input Module provides isolation, configurable thresholds, selectable filtering, and embedded counter measurement logic. These measurements can be synchronized with other frequency, analog, digital, and counter measurements in a single acquisition.
-
product
C Series Relay Output Module
The C Series Relay Output Module enables you to switch up to eight signals at 60 V maximum DC switching voltage and up to 250 V of maximum AC switching current. For quick reference, every channel features an LED to indicate the state of that channel. The C Series Relay Output Module allows for direct connection to a wide array of industrial devices such as motors, actuators, and DC devices.The C Series Relay Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Digital Input/Output Card
IOD-144
This is a 144-bit full-size card. A Programmable Peripheral Interface chip, type 8255-5 provides three 8-bit ports (A, B, and C) for each 24-bit group. Each port can be independently programmed for either input or output. Port C can also be configured as two 4-bit ports. These cards fully implement Mode 0 of the 8255 PPI chip. (Consult the factory if you desire to operate in Mode 1.) Type LS245 bi-directional transceivers sink 24 mA (optionally 64 mA) and source 15 mA. These transceiver buffers provide hysteresis correction on inputs and added drive capability on outputs. The direction of the transceivers is set by software.
-
product
Input-output Module
MOV48
M-module MOV48 is installed on the mezzanine carrier - module NM-M or MEZABOX and is connected to them via a local information highway.
-
product
Isolated Digital Input/Output Cards
PCI-IIRO-8 and PCI-IIRO-16
The PCI-IIRO-8 and PCI-IIRO-16 are low-cost, half-size cards that provide isolated input and output for PCI-Bus computers. The cards have eight or sixteen optically-isolated digital inputs for AC or DC control signals and eight or sixteen electro-mechanical relay outputs. PCI-IIRO-8 occupies four consecutive eight-bit registers in I/O space. PCI-IIRO-16 occupies eight consecutive eight-bit registers in I/O space.
-
product
256 Digital Input/Output Channels
CP387
The C387 is a single-width, 6U, CompactPCI module with up to 256 digital input/output channels. The C387 base board supports 128 channels of TTL I/O. Four mezzanine card sites can be populated with other forms of digital I/O including isolated input, isolated output, relay output, AC switch output or differential I/O. The mezzanine card concept allows multiple digital I/O types to be configured within a single module to match the application requirements.
-
-
product
USB Digital Input/Output Module
USB-DIO-32
The USB-DIO-32 is an ideal solution for adding embedded, portable, easy-to-install digital I/O and counter capabilities to any computer with a USB port. The USB-DIO-32 is a USB 2.0 device, offering the highest speed available with the USB bus. It is fully compatible with both USB 1.1 and USB 2.0 ports. The board is plug-and-play allowing quick connect or disconnect whenever you need additional I/O on your USB port.
-
product
48-Channel DIO (Digital Input/Output) PCMCIA Card
D480C
The D480C offers up to 48 separately controllable Digital I/O lines for general purpose control and monitoring applications.
-
product
CompactRIO Input-Output Modules
More than 50 input / output modules for various measuring tasks - analog and digital input / output, tensometry, vibroacoustic diagnostics, temperature measurements, control of external devices and telecommunications.
-
product
Input-output Module
OLS
The OLS module is a specialized device for input-output of logical information, intended for the formation and registration of asymmetrical logical levels of signals on 64 channels. The OLS module is made in the VXI standard and is functionally close to the DI-Series modules from Teradyne.
-
product
I/O Input/Output Board
VME-4514A
The VME-4514A Analog I/O (AIO) Board provides 16 high-quality analog output channels which can be programmed with on-board jumpers to operate in a variety of voltage ranges. Each output can source or sink 10 mA at ±10 V. For off-line testing, the analog outputs can be disconnected from the I/O connector.
-
product
GigE And 3x ASI Input/output For PCI
DTA-160
DekTec's Gigabit Ethernet adapter with three ASI/SDI ports, allowing zero-jitter transmission and reception of Transport Streams over IP networks; the additional three ASI ports allow easy conversion between the two interface types.
-
product
Digital Input/Output Expander (Normally-Open Relay Contact Outputs)
ENVIROMUX-DI16DOR16
Adds 16 digital inputs and 16 digital normally-open relay contact outputs to the ENVIROMUX-2D/5D/16D. Interfaces with the ENVIROMUX-2D/5D/16D via the RJ45 Sensor Port. Digital inputs: 16 screw terminal pairs for connecting dry contact devices; One screw terminal pair for tachometer; 0 to 255 Hz. Accepts 26 to 16AWG wire. Potential free. Voltage range: 0 to +36VDC. Over-voltage surge protected. Digital outputs: 16 screw terminal pairs for normally-open relay contact outputs. Accepts 26 to 16AWG wire. Potential free. Rated switching load: 0.5A @ 125 VAC, 1.0A @ ±30VDC. Fused. Supports CAT5/5e/6 cable up to 500 ft. (152.4 m). Includes 5V/3A power supply. Compatible with ENVIROMUX-2D/5D/16D. Dimensions WxDxH: 6.49x3.10x1.78 in (165x79x45 mm). Regulatory approvals: RoHS.
-
product
48-Channel DIO (Digital Input/Output) PCMCIA Card
D480C/i(DIOi480)
The D480C/i offers up to 48 separately controllable Digital I/O lines for general purpose control and monitoring applications.
-
product
48-Channel DIO (Digital Input/Output) PCMCIA Card
DIOi480(D480C/i)
The DIOi480 offers up to 48 separately controllable Digital I/O lines for general purpose control and monitoring applications.
-
product
Digital Input/Output and Counter/Timer Card
PCI-DIO-96C3
This is a 96 line digital input/output card with counter/timer capabilities designed for use in high I/O density application requirements. I/O connections are made via four 50-pin header connectors. The card is 12.25 inches long (312 mm) and may be installed in any full-length 5V PCI-bus (or PCI-X bus) slot in X86 type PC’s.
-
product
PMAC Input/Output (IO) Modules
PMAC Input/ output (I/O) modules offer a wide range of analog or digital IO including AC, DC, TTL and analog.
-
product
PC/104 Input/Output Module providing 96 lines of digital I/O
PCM-UIO96C-16
The PCM-UIO96C-16 is a highly versatile PC/104 input/output module providing 96 lines of digital I/O. One important feature of this card is its ability to monitor 48 of the 96 lines for both rising and falling digital edge transitions, latch them, and then interrupt the host processor notifying that a change-of-input status has occurred. This is an efficient way of signaling the CPU of real-time events without the burden of polling the digital I/O.
-
product
48 Channel Isolated Digital Input/Output Module
DP-VME-3078
DP-VME-3078 is a 48 Channel Isolated Digital Input Output Module. This module provides 48 input / interrupt channels and 48 digital output channels with isolation. The 48 channel inputs are divided into 12 groups, each group consisting of 4 channels and 1 common GND .The 48 output channels are divided into 6 groups, each group consisting of 8 channels and a common GND.
-
product
C Series Current Output Module
The C Series Current Output Module features up to eight channels of simultaneous analog output. You can choose between enclosed and non-enclosed modules. Additionally, the C Series Current Output Module has built-in open-loop detection. This detection generates an interrupt in software when an open loop is detected, zeros outputs to ensure safety, and avoids driving actuators at system power-on. The C Series Current Output Module requires an external power supply and includes a channel-to-earth ground double isolation barrier for safety and noise immunity.The C Series Current Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Low Profile Isolated Digital Input/Output Card
LPCI-IIRO-8
The LPCI-IIRO-8 is a half-size Low-Profile PCI bus compatible card that provides isolated digital input and output interface for PCI-Bus computers. The card has eight optically-isolated digital inputs for AC or DC control signals and eight electromechanical relay outputs. LPCI-IIRO-8 occupies four consecutive 8-bit registers in I/O space.
-
product
HDMI Input/Output FMC Module
AES-FMC-IMAGEON-G
Sundance Multiprocessor Technology Ltd.
The AES-FMC-IMAGEON-G HDMI input/output FMC module provides high-definition video interfaces for FMC-enabled baseboards. An HDMI video source can provide video content to the module. The module also provides an HDMI output to display FPGA driven video content.
-
product
64-Channel VME Digital Input/Output Module
V250
The V250 is a single-wide, 6U VME module that provides 64 non-isolated channels of digital input/output. Each 16-channel bank shares programmable pull-ups and input thresholds with a range of 0 to +10 volts.
-
product
24 and 48 Digital Input/Output Cards
PCI-DIO Series
The PCI-DIO-48/48S, PCI-DIO-48JP/JPS, PCI-DIO-48JPL/JPLS, PCI-DIO-48H/HS and PCI-DIO-24S are 24- and 48-bit parallel digital input/output cards designed for use in PCI-Bus computers.
-
product
Digital Input/Output Cards
PCI-DIO Series 24 and 48
The PCI-DIO-48/48S, PCI-DIO-48JP/JPS, PCI-DIO-48JPL/JPLS, PCI-DIO-48H/HS and PCI-DIO-24S are 24- and 48-bit parallel digital input/output cards designed for use in PCI-Bus computers. The card is 6.9 inches (175 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
