-
Product
VME-Bus Synchro - Resolver LVDT I/O Cards
VB Series
-
Computer Conversions Corporation
The "VB Series" product lines contains VME compatible synchro/resolver converters and absolute encoder systems. These particular cards are ideal for any rotary motion and related process, control, or simulator type application with any VME compatible system.
-
Product
Motion Control Solutions
-
DDC offers a complete line of Synchro/Resolver instrument-grade cards and test equipment including angle position indication and simulation, plus a variety of hardware and software to meet today’s civil, military, and COTS/MOTS requirements. DDC is a leading supplier of Synchro/Resolver-to-Digital and Digital-to-Synchro/Resolver components—the smallest, most accurate synchro/resolver-to-digital and digital-to-synchro/resolver converters available today. Most of these single chip and hybrid converters are based on ASIC designs, yielding the most reliable and affordable converters ever offered, and are the building blocks for DDC’s card-level products.
-
Product
Synchro to Digital-Resolver to Digital Converters
SACP-RACP
-
Computer Conversions Corporation
Computer Conversions Synchro-Resolver to ACP/ARP Converters accept choice of synchro-resolver input options, power input, and mounting configuration, converts synchro/resolver input into ACP (Azimuth Change Pulse) and ARP(Azimuth Reference Pulse) type outputs suitable for 75 ohm drive.
-
Product
P104 Synchro/Resolver Simulation Board
73DS2
-
NAI’s 73DS2 is a PC104-compatible Synchro/Resolver Simulation Board with three isolated channels. These channels can incorporate up to three Digital-to-Synchro/Resolver Converters with 1.2 VA drive capability in a stack-through module. With galvanic isolation, one of the outputs can be grounded without affecting performance.
-
Product
Synchro/Resolver to Linear DC Converter
-
NAI offers a variety of Synchro/Resolver Converters that continuously transform Synchro or Resolver inputs into digital form. These solid-state modules provide resolution to 16-bit and accuracy to 19.8 arc-seconds, and are error-free up to the maximum specified tracking rate. They are transformer-isolated and operate over a frequency range from 47 Hz to 10 kHz. The modules are specifically designed for rugged defense and industrial applications.
-
Product
3U cPCI Synchro/Resolver Simulation Board
75DS2
-
NAI’s 75DS2 is a Synchro/Resolver Simulation Board with four independent, isolated channels. These channels can incorporate up to four Digital-to-Synchro/Resolver Simulation Converters with 1.5, 2.2, or 3 VA drive capability, or either two or four Digital-to-LVDT/RVDT Simulation Converters. One of the outputs on each channel can be grounded without affecting performance.
-
Product
Synchro/Resolver Boosters
-
NAI offers a variety of multi-channel Synchro/Resolver Boosters that accept Synchro/Resolver inputs, and they deliver isolated outputs capable of driving passive and active loads such as Control Transformers or Torque Receivers. These amplifiers can be used stand-alone or in conjunction with Digital-to-Synchro/Resolver Converters.
-
Product
AC-DC Rectifier / Converters
-
These following AC-DC converters all can provide 3.3/5/9/12/25/24/28/48V etc output. Newly acquired 2U rack mount 48V rectifier is a mature solution for 48V telecom systems.
-
Product
725-Watt (270VDC input) DC/DC Converter, SOSA™ Aligned, 3U VPX
VPX57HS
-
NAI’s VPX57HS-31 is NAI's latest +270 VDC Input, VPX DC/DC Converter. The VPX57HS was developed in alignment of the SOSA™ Technical Standard and is capable of handling up to 725 Watts of output power. It plugs directly into a standard 3U VPX chassis with a VITA 62 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
25-Watt DC/DC Converter
55GS1
-
NAI’s 55GS1 is a COTS, 25-Watt DC/DC Converter that accepts a +28 VDC input and provides a single full-power output at a baseplate temperature of +100°C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
Product
Optical-Electrical Converter - PXI
O2E 1000 – 1400 Series
-
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
Product
725-Watt (28VDC input) DC/DC Converter, SOSA™ Aligned, 3U VPX
VPX55HS
-
NAI’s VPX55HS-31 is NAI's latest +28 VDC Input, VPX DC/DC Converter. The VPX55HS was developed in alignment of the SOSA™ Technical Standard and is capable of handling up to 725 Watts of output power. It plugs directly into a standard 3U VPX chassis with a VITA 62 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
600-Watt DC/DC Converter, 6U VME/cPCI
55U91-01
-
NAI’s 55U91-01 is a 600 Watt DC/DC Converter that plugs directly into two card slots in a standard 6U VME chassis. It is conduction-cooled through the card edge/wedgelock. This switching power supply accepts +28 VDC input, provides up to 9 outputs at up to 614 Watts, and addresses the power supply needs of both VME and cPCI systems.
-
Product
400-Watt DC/DC Converter
VPX55-3
-
NAI's VPX55-3 is 400-Watt DC/DC Converter that plugs directly into a standard 3U VPX chassis with a VITA 62 0.8" power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
75/150-Watt DC/DC Converter w/Holdup, 3U cPCI
75PS4
-
NAI’s 75PS4 is a DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This programmable, switching power supply accepts a +28 VDC input and is available in either a 75 Watt or 150 Watt-version.
-
Product
Digital to Synchro Converter
DSPH
-
Computer Conversions Corporation
The DSPH Series High Power Digital to Synchro Converters, are proven, high efficiency, low cost, compact, reliable solid state synchro drivers; designed for demanding Naval/Maritime, Aircraft, fire control and Radar/Antenna related, applications. They are commonly used on synchro based data transmission, retransmission, simulation, and instantaneous absolute position indicating and active control systems.
-
Product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
-
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
Product
100-Watt DC/DC Converter, 3U cPCI
55LQ2
-
NAI’s 55LQ2 is a 100 Watt DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This modular, switching power supply accepts +28 VDC input and provides a single output at up to 100 Watts.
-
Product
125-Watt DC/DC Converter, 3U cPCI
55LQ3
-
NAI’s 55LQ3 is a 125 Watt DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This modular, switching power supply accepts +28 VDC input and provides a single output at up to 100 Watts.
-
Product
1000 Watt AC/DC Power Converter, 6U VPX
VPX56H-6
-
The VPX56H-6 is NAI's latest high power, 1000 Watt AC/DC converter which accepts either a 3Ø 115VAC L-N inputs or a +270 VDC input. It plugs directly into a standard 6U VPX chassis with a (VITA 62) 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
8 channel 16 bit Digital to Analog Module
CPCI-DA8-2
-
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system.
-
Product
Dynamic D/A Converter, 16-channels, 16-Bit, Unipolar, 30 V/20 mA
M9188A
-
The M9188A is a PXI based, 1-slot unipolar Dynamic DAC which has 16 channels capable of supplying typical waveforms at high voltages. It has 4 isolated banks with 4 channels in each bank.
-
Product
Transition Time Converter, 250ps
15432B
-
The new design of these transition time converters ensures very low signal reflection far beyond the 3 dB point, unlike conventional converters. Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications. The converters are fitted with SMA connectors, one male, one female. These converters have been designed to convert the fixed transition-times of the Keysight 8133A 3 GHz timing generator (<100 ps transitions) to slower, fixed transition-times (150 ps, 250 ps, 500 ps, 1 ns, 2 ns) hence reducing the signal bandwidth. All transition-times are from 10% to 90% of amplitude.
-
Product
PXI 8/16-Channel Isolated D/A Converter
M9185A
-
The M9185A is a fully independent, isolated D/A converter that is capable of supplying high voltage levels in parallel of up to eight or sixteen channels. Each channel is able to output up to 16V as stimulus signals to Device Under Tests (DUTs).
-
Product
100-Watt DC/DC Converter
55LS1
-
NAI’s 55LS1 is a COTS, 100 Watt DC/DC Converter that accepts a +28 VDC input and provides a single full-power output at a baseplate temperature of +100° C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
Product
Optical-Electrical Converter - MATRIQ
-
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
Product
Synchro to Digital-Resolver to Digital Converters
HRDCK-HSDCK
-
Computer Conversions Corporation
HSDCK and HRDCK series are the highest accuracy, miniature tracking synchro and resolver to digital converters in the marketplace. They are designed specifically for ultra precise requirements in the most demanding industrial and military applications.
-
Product
8 channel 16 bit Digital to Analog
CPCI-DA8-1
-
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system. The CPCI-DA8 is supported by ALPHI Technology under Windows NT by a Board Support Package which is supplied with the card. Other documentationsupplied with the card will describe this support in full detail.
-
Product
P104 Synchro/Resolver Measurement Board
73SD4
-
NAI’s 73SD4 is a DSP-based, PC104-compliant Synchro/Resolver Measurement Board with six separate, isolated channels. These channels can incorporate up to six Synchro/Resolver-to-Digital Tracking Converters in a stack-through module. Each channel also produces differential incremental encoder (A & B) outputs (with programmable resolution) and a zero-degree marker pulse. Commutation outputs are available for 4-, 6-, or 8-pole brushless DC motors that eliminate the need for Hall Effect sensors, thereby reducing both processor time and bus traffic.
-
Product
Synchro to Digital and Resolver to Digital Converters
-
Computer Conversions Corporation
Resolution: Up to 20 Bit Single-speed Resolution, Up to 24 Bits Multi-Speed Multi-Turn Resolution.Accuracy: +/- 7 to +/-19 arc seconds 20 bit, +/-40 arc seconds 16 bit, +/- 1',+/-2.3 and +/-4' Reference Inputs: 2- 11.8V 26/ 115Vrms L-L 47 to 10,000 Hz. Isolated to > 500VDCSignal Inputs: 2 - 11.8, 26, 40, 90V.L-L. Isolated to . 500VDC.Options: Multispeed synchro input and bus card interface.
