-
Product
Keying Pin Kit, Receiver/ITA
310118112
-
The Keying Pin kit is a way to avoid damaging the contacts within the ITAs and Receivers. Simply insert the longer keying pins into the receiver and the smaller set screws into the ITA to create the pattern needed to isolate your test fixtures so there is no operational mismatch.
-
Product
Compliant Connectors
-
*Superior durability in high life cycle applications*Widest range of applicationsFlexible architecture
-
Product
Three Meter Fully Compliant Chambers
-
3 Meter Fully Compliant semi-anechoic chambers offer semi-anechoic radiated emissions (RE) and fully anechoic radiated immunity (RI) compliance test capability for most international EMC compliance regulations.
-
Product
Standard Method Compliant
-
Shimadzu System GC Analyzers are built and tested to meet the specific analysis requirements of applicable industry standards.
-
Product
Load Pins
-
They are used in many diverse applications including cranes, winches, agricultural equipment (such as tractors), fishing, marine, offshore, subsea, aerospace, process industries, mining, hoisting gear, elevators and floor conveyors, cable laying machinery and many others. The load information provided by the pin can be used for process control, weight/force measurement, overload protection and safety related aspects.
-
Product
Screw Pins
-
C.C.P. Contact Probes Co., LTD.
CCP's Screw Pin is an extremely smart way to utilize a pogo pin as a connector as well as a mounting part.
-
Product
EU Regulation Compliant GC-MS/MS Method Package For Dioxins In Foods
-
The analysis of dioxins in foods was mainly performed using magnetic sector (double-focusing) GC-MS instruments. However, in June 2014, the GC-MS/MS method was officially recognized in the EU as being equivalent to the magnetic sector GC-MS method (EU 589/2014). This product consists of method files for the analysis of dioxins in foods, and a report creation tool, supporting the analysis of dioxins via GC-MS/MS.
-
-
Product
P-Series Modular Power Meter (LXI Compliant)
N8262A
-
The Keysight N8262A P-Series modular power meter enables LAN-based automated measurements of peak, peak-to-average ratio and average power. The N8262A enables fast, efficient, and cost-effective creation and reconfiguration of your ATE system. Owing to LXI test standardization and its interoperability with existing test assets, your system can be up and ready in no time.
-
Product
SHC68-C68-S, 68 pin VHDCI to 68 pin VHDCI, 0.5m
186380-0R5
-
SHC68-C68-S, 68 pin VHDCI to 68 pin VHDCI, 0.5m
-
Product
Digital PIN Electronics Module
P128C200M
-
The P128C200M module provides measurement and control of parameters of integrated circuits using parametric measurement methods, as well as functional and algorithmic control. The module implements a synchronization system that ensures the operability of a group of modules when they are installed in the AXIe-1 crate.
-
Product
Interface Pin
-
Smiths Interconnect offers interface probes for all major test equipment manufacturers. We also provide a variety of interface pins for use in test fixtures.
-
Product
VME Bus Pin Assignments
-
VECTOR Electronics and Technology, Inc.
VME bus connector pin assignments and signal descriptions per ANSI/VITA 1.1-1997
-
Product
Additional Products: 200 Pin D Cables - 200 Pin to 200-Pin
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Pin Pointer
CFL PP3+
-
The new generation CFL PP3+ Cable Fault Pin Pointer cum route tracer from SCOPE is the ultimate solution for locating of underground cable faults in minimum time by tracing cable route. It uses an advanced technology which helps even an unskilled operator to locate the fault accurately.
-
Product
25 Pin Breakout Interface
VSI-Breakout-25
-
The VSI-Breakout-25 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
-
Product
Keying Pin Kit, ISeries, Receiver And ITA
310113461
-
The iSeries keying pin kit includes a set of two hex keys. One hex key will allow 6 different options and two can provide 36 different keying options. The keying kit provides a way to isolate your connectors to prevent operational mismatch.
-
Product
200 Pin D Cables - 200 Pin to Alternative Connector for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 200-pin D connector.
-
Product
Pin Insertion Tool For Scorpion Connectors With Crimp Pins
C020AFR-2CP-2A-I
-
Extractor tool for crimp pins fitted into a Scorpion connector housing.
-
Product
50 Pin D-type Connectors & Cables
-
These standard voltage and high voltage 50 Pin D-type connectors are used for both PXI & LXI switching and simulation products for medium density applications.
-
Product
68 Pin 1.27mm Pitch Micro-D Cables - 68 Pin to 68 Pin for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 68-pin micro-D connector.
-
Product
SHC68-C68-S, 68 pin VHDCI to 68 pin VHDCI, 2m
186380-02
-
SHC68-C68-S, 68 pin VHDCI to 68 pin VHDCI, 2m
-
Product
68 Pin Breakout Interface
VSI-Breakout-68
-
The VSI-Breakout-68 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
96 Pin 1.27mm Pitch Micro-D Cables - 96 Pin to Alternative Connector for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 96-pin micro-D connector.
-
Product
96 Pin 1.27mm Pitch Micro-D Cables - 96 Pin to 96 Pin for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 96-pin micro-D connector.
-
Product
Compliant Connectors
MIL-DTL-55302
-
High reliability 55302 compliant connectors with mixed signal, power and coaxial contacts designed for defense, commercial aerospace and space demanding applications
-
Product
SOLAS Compliant Container Weight Verification System
-
Cargo Hawk is a non-intrusive SOLAS compliant Container Weight Verification system. Using Datum Electronics highly accurate and patent protected innovative bolton strain gauge sensors, Cargo Hawk seamlessly integrates to new and existing container handling equipment, without the need of introducing expensive high wearing consumable load monitoring hardware.
-
Product
50 Pin IDC Connector Breakouts
-
The connector breakouts below are suitable to use with Pickering cabling products that utilize a 50-pin IDC connector.
-
Product
Additional Products: 100 Pin 1.27mm Pitch Micro-D Cables - 100 Pin To 100-Pin
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
