-
Product
CompactPCI
-
CompactPCI is a computer bus interconnect for industrial computers, combining a Eurocard-type connector and PCI signaling and protocols. Boards are available in 3U or 6U sizes
-
Product
CompactPCI Chassis
-
CompactPCI is a standard in computer bus technology for industrial computing that utilizes a Eurocard type connector combined with PCI signaling and protocols. cPCI boards come in 3U and 6U variants and are typically interconnected through a passive backplane. The connector pin assignments are standardized by PICMG , allowing for eight boards in a PCI segment with multiple bus segments being allowed with the use of active bridges.
-
Product
CompactPCI
3U PMC Carrier
-
This conduction cooled 3U CompactPCI single slot PMC provides an active interface between the CompactPCI bus (backplane) and a PCI Mezzanine Card (PMC). This product addresses the needs of aerospace, military, and rugged applications. It contains a thermal heat frame made of aluminum that fits together with conduction cooled PMC modules. Conduction cooling conducts heat away from the hot spots of the board and transfers the heat to the card edges and to the system chassis. No active ventilation is necessary inside of the system, which means the boards are sealed from the environmental influences found outside of the chassis. The heat frame and integrated wedge locks for the conduction cooling stiffens carrier and PMC module enabling the board to resist high shock and vibration.
-
Product
CompactPCI Backplanes
-
ADLINK offers a wide range selection of standard backplanes for different demands with various specifications..
-
Product
CompactPCI 14+2 Slot
-
The CompactPCI® 14 CPCI slot + 2 PSU slot backplane uses CPCI bridging to enable 2 PCI segments.
-
Product
CompactPCI Chassis for 3U
-
Advantech offers 3U or 4U height enclosures for 3U CPCI boards, with fan or fanless, and with CPCI legacy backplane or CPCI plusIO backplane.
-
Product
PMC Carrier for 3U CompactPCI
TCP270
-
The TCP270 is a standard 3U CompactPCI carrier that provides front I/O and rear I/O for a single width PMC module. This PMC to 3U CompactPCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in CompactPCI systems.
-
Product
3U CompactPCI Serial Blades
-
The PICMG CPCI-S.0 CompactPCI Serial standard, which evolved from the PICMG 2.0 specification, is the fastest, most versatile, most cost-effective open standard for CompactPCI (CPCI). The Serial standard is mechanically and electronically compatible with 3U and 6U euro-cards, defining an interface for high-speed switched fabrics with a star topology. Point-to-point connectors allow up to eight peripherals on one system slot without switches or bridges. Ethernet data transfer can be configured with full mesh topology, which allows up to 1000Base-T connections to all peripheral slots for redundant, safety-critical systems.
-
Product
CompactPCI 3U Backplanes
-
COMTEL Electronics offer a large variety of CompactPCI 3U Backplanes, 2 – 14 slots 32 bit 33/66Mhz, fully compliancy with PICMG 2.0 Rev 3.0 Specs. & Hot Swap compliant per PICMG 2.1 R2.0 Spec.
-
Product
CompactPCI Boards
-
*CompactPCI (cPCI) boards are 3U or 6U boards connected via a passive PCI (Peripheral Component Interconnect). Up to 8 boards can be connected together in a segment. Segments can be connected through bridges. *They are grouped into four categories: CPU, Communication, Input/Output, PMC carrier.
-
Product
PCI / PMC / CompactPCI Test System
PCITS
-
The CPCI850 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
6U CompactPCI
-
Advantech offer 6U CompactPCI CPU boards, rear transition modules, peripheral boards, and support for PMC or XMC module.
-
Product
CompactPCI Serial Chassis
-
CompactPCI Serial is an industrial standard for modular computer systems. It is based on the established PICMG 2.0 CompactPCI standard, which uses the parallel PCI bus for communication among a system’s card components. In contrast to this, CompactPCI Serial uses only serial point-to-point connections. CompactPCI Serial was officially adopted by the PCI Industrial Computer Manufacturers Group PICMG as PICMG CPCI-S.0 CompactPCI Serial in March 2011.
-
Product
6U CompactPCI Boards
-
Full line of 6U CompactPCI products supporting PICMG 2.16, IPMI, Hotswap, TPM, System Management.
-
Product
Stepper Motor Controller for CompactPCI
CPCI321
-
The CPCI321 Intelligent Stepper Motor Controller with amplifiers is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead.
-
Product
4U CompactPCI Hybrid PlusIO System with 5 CompactPCI and 4 CPCI-S.0 Peripheral Slots
cPCIS-P2630R
-
- 3U CompactPCI PlusIO backplane with five CompactPCI and four CPCI-S.0 peripheral slots and one system slot- Temperature, voltage, and fan monitoring LEDs- Supports rear I/O backplane with P2 connectors for CompactPCI 50mm depth RTMs- Hot-swappable cooling fans & filter- 400 W ATX Power supply
-
Product
ELOS CompactPCI Serial
ELOS-CPCIS
-
ELOS is an embedded rugged CompactPCI Serial system platform for a wide range of applications. The cost-efficient concept is based on modular building blocks that make this product extremely flexible.
-
Product
CompactPCI PICMG 2.16 Backplanes
-
Comtel Electronics offers a large variety of CompactPCI 2.16 Backplanes, 8 – 14 slots 64 bit 33Mhz,Fully compliancy with PICMG 2.0 Rev 3.0 Specs & 2.16 Spec. Hot Swap compliant per PICMG 2.1 R2.0 Spec.
-
Product
8 Channel ADC for CompactPCI
CPCI393
-
The CPCI393 8-Channel Differential Input ADC card is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs the data acquisition and calibration transparent for the host.
-
Product
PICMG 2.11 3U CompactPCI 47-pin Power Backplanes
cBP-3061/cBP-3062
-
- PICMG 2.0 CompactPCI Specification Rev. 2.1 compliant- Design for 47-pin 3U CompactPCI redundant power supply*- cBP-3061 for single power supply, cBP-3062 for dual power supply- AC (and DC) Screw terminal input
-
Product
16 Channel ADC for CompactPCI
CPCI392
-
The CPCI392 16-Channel Common-Mode Input ADC card is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs the data acquisition and calibration transparent for the host.
-
Product
3U CompactPCI Serial 2-Port CAN From PEAK Module
cPCI-A3CAN
-
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP- 2x D-Sub CAN ports in front panel- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
6U CompactPCI Dual 64-bit PMC Slots Carrier Board
cPCI-8602
-
- Supports two single-size 32,64-bit/33,66 MHz PMC sites in 4HP width- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- PICMG® 2.1 Hot Swap Specification Compliant- 3.3V or 5V V(I/O) for cPCI bus and PMC sites- PLX® PCI-to PCI bridge PCI6154 for PCI bus- Power and HotSwap LED incidators on front panel
-
Product
3U CompactPCI Serial Power Interface Board
046-201
-
Standalone Power-BP 3U 8HP to connect CPCI Serial power supplies to compactPCI Serial-BPs. The connection is made via cables.
-
Product
CompactPCI Serial 8 Slot 9U
-
The CompactPCI® Serial backplane is designed to be used with CompactPCI Serial 9 Slot 4U chassis.
-
Product
3U CompactPCI Serial 9-slot SSL w/o RTM w/ Ethernet
1CPCIS-309-L200
-
3U CompactPCI Serial Backplane with 9 CompactPCI S.0 slots, system slot left, without rear IO : 1x CompactPCI S.0 CPU slot, 8x CompactPCI S.0 peripheral slots, without connectors for Rear Transition Modules (RTMs), Ethernet full mesh.
-
Product
CompactPCI Backplanes
-
Model types include 3U and 6U, 32bit and 64bit, 33 MHz and 66 MHz. We offer several variations including EasyCable, EasyPlug, Low Profile, 32-bit, PICMG 2.16, and the latest CompactPCI Serial.
-
Product
4U 8-Slot CompactPCI® System with Redundant Power Supplies
cPCIS-6418U
-
The cPCIS-6418U Series Subsystem is designed for maximum density and has 8 horizontal slots for 6U cPCI boards with 80mm RTMs. The chassis is 4U in height and standard 19" rack mount width.
-
Product
CompactPCI CTEL 7U 2 Slot with H.110 bus, P1-2s
105CTEL702-0136
-
CompactPCI CTEL 7U 2 slot with system slot left, H110 bus, fully compliant to the PICMG basic specification 2.0 R3.0, Hot Swap specification 2.1 R1, andv PICMG H.110 Computer Telephony specification 2.5 R1.0.
-
Product
3U CompactPCI Serial 5-slot SSR w/ RTM no Ethernet
1CPCIS-305-R010
-
3U CompactPCI Serial Backplane with 5 CPCI-S.0 slots, system slot right, with rear IO: 1x CPCI-S.0 CPU slot, 4x CPCI-S.0 peripheral slots, with connectors for RTMs in slots 2 to 5, system slot (Slot 5) has one connector for RTM -> 5RJ6 - no Ethernet.
