-
product
Encoder And Decoder Unit
MS 2003
Encoder Decoder Unit is used to interact with ground station through PCM interface. Receives and transmits command/status information on Lakshya aircraft. Also provides real time clock synchronization, latitude/longitude information and IRIG-B Time. System is a digital, high speed FPGA controlled, intelligent unit to interact with various sub systems.
-
product
Data Retrival and Analyzer Unit
MS 1200
*Retrieves the Data from Magnetic / Solid State Recorders (Supports JAGUAR, AN32, IJT, ALH Platforms)*RS232/RS422/Bi-Phase/USB interface with PC AT*Presents Error Messages and Test Reports*Replay, Analysis and printout of selected parameters*Calibration facility for ADR and DAU*Portable System for Snag Analysis of Aircraft*Reports in Tabular/Graphical formats*Used to check serviceability of ADR, DAU without removing from aircraft
-
product
Pan/Tilt Unit for Side-Mounted Payloads up to 70 lbs
FLIR PTU-D300E
The PTU-D300 E-Series supports any type of single or multi-part payload through a flexible bracketing system of top and/or side mounting. Easy to integrate, the PTU-D300 E-Series is an open platform that provides the flexibility needed while minimizing your development and integration effort. The PTU-D300 E-Series has been proven in a wide range of mission critical applications for positioning of cameras, lasers, antennas, or other instruments in both fixed and mobile environments.
-
product
50 Channel Linear Vibration Motor Aging Unit
BK2021
The BK2021 50 Channel Linear Vibration Motor Aging Test System was designed to test your linear vibration motors so you know they are working. Load a jig drawer in the jig assembly unit with 10 DUT's. Close the drawer to start testing and begin loading the next of the 5 drawers. When the machine has finished running up to 4 test sequences that you've programmed in, the drawer opens. On the front, a green light tells you the motor is good, a red light tells you there was a short and if there is no light you know there was an open circuit.
-
product
Nano Interface Unit
NIU2A
NAI’s NIU2A contains an integrated power supply, two function module slots and an optional ARM® Cortex®-A9 processor. This small, low-power unit is ideally suited for rugged military, industrial, and commercial applications. It delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems — in less time, with NO NRE.
-
product
Unit Injector Expert
UInEx-2
UInEx-2 (Unit Injector Expert) is a device for comprehensive diagnostics of passenger car unit injectors. It enables detailed electrical and mechanical tests, such as:
-
product
Combined Map Display Unit & Interface Unit Tester (COMED)
MS 1117
This system is used to test COMED (Combined Map Electronic Display) IFU cards. This ATE checks the LRU Status and card status and identify faulty component in the individual UUT. On fault, this suggests the possible component failure as diagnostic report, for repairing the cards.
-
product
Benchtop Unit for Universal Coating Thickness Measurement
FISCHERSCOPE MMS PC2
Multifaceted for coating thickness measurement and material testing. Universal multi-measuring system for parallel coating thickness measurement and material testing with up to eight measuring modules.
-
product
VLF Testing and Diagnostics Unit
Frida TD
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR frida TD. The portable and high performance high-voltage testing and diagnostics device is available in two different configurations: frida: Used for cable and cable sheath testing of medium-voltage cables and electrical equipment up to 20 kV. Another function is insulation testing on electrical equipment.frida TD: Expands the functional scope of frida with the tan delta diagnostics and Monitored Withstand Test (MWT) that combines the cable testing and dissipation factor measurement. This allows for an accurate and comprehensive assessment of the cable condition.* Cable testing and dissipation factor diagnostics in one device* Easy and quick test setup* Automatic testing and diagnostic sequences* Compact dimensions and lightweight
-
product
Unit Testing Mocking Solution for .NET
Coverage
Isolator displays your code coverage instantly in your editor while you code, which means you can spot uncovered areas while the code is fresh in your mind.
-
product
Color Measuring Unit
Colorette 4
The Colorette 4 serves for precisely measuring the colour of ground roasted coffee. By means of the stripping device, the sample to be measured is prepared and afterwards positioned at the measuring point. The Colorette works according to the principle of reflection measurement. A ground coffee sample to be measured is illuminated with a white clock-pulsed LED. For colour value determination, the reflected light is thereby captured by a sensor. The determined colour value is afterwards indicated on the touch screen. The indication in different scales makes it possible to use the device flexibly and to adapt it individually to the requirements. Thanks to the improved components, the Colorette 4 is low-wear and guarantees most exact measuring results during the entire lifetime. The extended connectivity offers various integration possibilities into processes and systems.
-
product
Vibration Control, Monitoring and Diagnostics System for Hydraulic Units
Stationary system for vibration control, monitoring and diagnostics of hydraulic units is used for constant technological and safety control, diagnostics of vibrational and mechanical parameters of hydraulic units and auxiliary equipment of hydroelectric power stations in accordance with the applicable requirements.
-
product
Front Panels for Plug-In-Units | IEEE
EMC front panel for IEEE plug-in-units | 3 and 6 U | up to 14 HP
-
product
Programmable AC&DC Power Supply Unit
PADS
The energy feedback type programmable AC/DC power source with energy feedback unit equipped functions of voltage adjustable, frequency adjustable, harmonic controllable, low voltage ride through simulation etc.
-
product
Dual Function Slot MOSA Data Concentrator Unit (DCU)
NIU2A-DCU-01
NIU2A-DCU-01 is a Modular Open Systems Approach (MOSA) Data Concentrator Unit with low power high performance ARM Cortex -A9 processing. 512 MB RAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet and optional Fiber Optic Ethernet support
-
product
Fuel Display Unit Tester
MS 1125
Fuel Display Unit Test Bench is a compact table-top test bench with front panel controls, indications, built-in signal simulator and necessary power supply for testing the serviceability of Fuel Display Unit of Helicopter. FTB operates on 230 V AC and supplies 28 V DC power to FDU. FTB is housed in a metallic cabinet FTB interfaces with both 61 Pin connector and 6-pin socket mounted on the rear panel of FDU by means of the cable connected to the unit. FTB is fabricated utilizing off-the-shelf standard industrial/commercial components like rotary switches, toggle switches, press switches, test sockets, fuse holders, potentiometer etc. The Frequency generation circuit is integrated into FTB for the simulation of Fuel probe and flow rate signals. The frequency of the signal can be selected by means of a rotary switch Low amplitude sine wave signal is simulated for testing flow rates. Variable voltage DC power supply with a voltage range of 24 to 29 Volts is provided within FTB to power-up FDU. 5 V DC is provided for the operation of signal generating circuit (PIC Frequency Controller Board). An off-the-shelf Hand held battery operated Digital Multimeter (DMM) procured from the prominent manufacturer (FLUKE) is supplied with FTB for setting up and measurement of various parameters like Resistance, Voltage, Frequency etc.
-
product
Thermometer REPLACED BY PTM-1
BA T-7001H
In applications where clinical accuracy is not mandatory and cost is a consideration , the BAT-7001H is Physitemp‘s most compact, low cost thermocouple thermometer. The Model BAT-7001H is a high performance, precision hand-held instrument for the measurement of temperature using Type T (copper-constantan) thermocouples. This versatile instrument measures temperature in both °C and °F. The internal memory of the micro-computer stores the minimum and maximum measured temperature for instant recall via the LCD display. BAT-7001H operates on a 9V battery.
-
product
Standard 0.50 (14.00) - 2.00 (57.00) Non Replaceable General Purpose Probe
A-A-S-C
Current Rating (Amps): 2Average DC Resistance lower than (mOhm): 30Test Center (mil): 39Test Center (mm): 1.00Full Travel (mil): 30Full Travel (mm): 0.76Recommended Travel (mil): 20Recommended Travel (mm): 0.51Overall Length (mil): 310Overall Length (mm): 7.87Rec. Mounting Hole Size (mil): 31.5Rec. Mounting Hole Size (mm): 0.80Recommended Drill Size: #68 or 0.79 mm
-
product
Safety Control Unit
Epec SC52
SC52 offers a flexible solution for software-based safety function implementation. Together with the SC52 controller, Epec offers a set of pre-certified PLCopen application libraries in order to reduce customer’s safety related software development effort.
-
product
Total Nitrogen Unit For TOC-L Series
TNM-L
Perform simultaneous TOC and TN measurements. *720 °C catalytic thermal decomposition/chemiluminescence methods are adopted for TN measurement. There is no interference from metallic ions or bromine in sea water.*Measurements over a wide range with a detection limit of 5 μg/L for TOC-LCH to an upper limit of 10,000 mg/L.
-
product
Safety Relay Unit for PNP Output (Equivalent) Type Light Curtain
SF-AC
Panasonic Industrial Devices Sales Company of America
Safety Relay Unit compatible up to control Category 4. This device incorporates power supply terminals and synchronization line terminals for the Light Curtain, so terminal blocks are not required.
-
product
GPS Time Synchronization Unit
Signals & Systems India Private Limited
GPS Time Server – GPS-DRM-1010 is a compact DIN rail mountable unit that synchronizes and maintains the timing and frequency requirement of power and process industry equipment using a signal obtained from different external sources such as GPS and GLONASS. It provides nanosecond accuracy when external time references are not available. It has a storage facility to store the system log file. It delivers NTP, SNTP, IRIG-B, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through a Web-based application.
-
product
Pan/Tilt Unit for Side-Mounted Payloads up to 25 lbs
FLIR PTU-D100E
The PTU-D100 E-Series supports any type of single or multi-part payload through a flexible bracketing system of top and/or side mounting. It has been designed to be simple to integrate. The PTU-D100 E-Series is an open platform that provides the flexibility needed while minimizing your development and integration effort. It has been proven in a wide range of mission-critical applications for positioning of cameras, lasers, antennas, or other instruments in both fixed and mobile environments.
-
-
product
High Temperature Testing Mobile Conversion Unit
Used for applications that require high temperatures (1800C-2000C) for extended periods of time, the High Temperature Mobile Conversion Unit offers enhanced capabilities to accommodate more damanding requirements.The unit is based on the General Purpose MCU which allows for the use of standard specimen grips and accesories.
-
product
Phasor Measurement Unit Calibration System
6135A/PMUCAL
The 6135A/PMUCAL system is the only fully automated and traceable PMU calibration system available today. It fully complies to the IEEE C37.118.1™-2011 and section 7 of IEEE C37.242:2013 standards for PMU operation and verification.
-
product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A, Hardware Interlock
40-194A-001-HI
The 40-194A-001 is a 7-Channel PXI Fault Insertion switch with hardware interlock and one fault bus, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
product
Regulated Power Conversion Unit
RPCU
The RPCU takes variable frequency 3-phase 115VAC input power (324Hz to 800Hz) and converts it to regulated 28VDC output. Astronics currently offers two RPCU options: 250 Amp output and 150 Amp output.
-
product
Standard 0.39 (11.00) - 1.39 (39.00) Replaceable General Purpose Probe
MEP-30B
Current Rating (Amps): 2Average Probe Resistance (mOhm): 50Test Center (mil): 30Test Center (mm): 0.76Full Travel (mil): 75Full Travel (mm): 1.91Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 690Overall Length (mm): 17.53
-
product
PXI-2510, 68-Channel, 2 A PXI Signal Insertion Switch Module
778572-10
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
