-
Product
COM Express
-
COM Express, defined by the PCI Industrial Computer Manufactures Group (PICMG), is the most successful Computer-On-Module (COM) standard in the embedded market today. COM Express employs a mezzanine-based approach, whereby an off-the-shelve module with two 220-pin board-to-board connectors, plugs into a custom, application-specific carrier board.
-
Product
3U OpenVPX™ Rugged, Cybersecure & Anti-Tamper Single Board Computer
68ARM2
-
The 68ARM2 is a 3U OpenVPX Zynq® UltraScale+™ Quad-core ARM® Cortex™-A53 MPCore™ based Single Board Computer that can be configured with up to three NAI Smart I/O and communications function modules. Ideally suited for rugged Mil-Aero applications, the 68ARM2 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
Computer Conversions GT Transducers
R90-11GS
-
Computer Conversions Corporation
Computer Conversions GT Transducers are brushless, Electromagnetic, Rotary Sensors used to provide Precise Absolute or Incremental Position, and Velocity feedback in harsh environments. All Computer Conversions Transducers are continuous rotation, bi-directional, and electronically passive devices (no electronic components to degrade or fail), that require zero maintenance, and may be installed in virtually inaccessible locations.
-
Product
IC-INT-VPX3d, 3U OpenVPX Intel Xeon Single Board Computer
IC-INT-VPX3d
-
The IC-INT-VPX3d is a powerful OpenVPX 3U Single Board Computer (SBC) based on Intel’s High Performance Low Power Spectrum processors for high performance embedded computing (HPEC).
-
Product
IRIG Time Code Receiver & Generator for Computers (PCI Express)
TCR180PEX
-
Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. The output format is independent from the incoming IRIG signal - a perfect solution to your IRIG conversion requirements. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements) or as an IRIG converter device.
-
Product
Air Data Computer (ADC) Tester
MS 1122
-
The ADC tester is used in 2nd line maintenance is to check the functionality of ADC. This unit is a rugged customized hardware based on full functionality test of ADC. The Air Data Computer (ADC) Tester is a fully automated GO/NOGO tester with full functional testing in 2nd line maintenance. This tester is to test ADC at unit level and identify faulty Shop Replaceable Unit (SRU). This tester is also used to carry out PI checks on ADC before clear them for installation on aircraft. ADC Interface board designed to test full functionality of ADC. The Air Data Computer (ADC) test equipment shall be used for testing ADC of Tejas Aircraft. ADC test equipment shall verify the functionality against specifications during second line maintenance and pre-installation on the aircraft.
-
Product
Robotic and Computer Programming System
Sense
-
Sense is a robotic and computer programming system which allows users to explore, problem solve, and advance their computer programming abilities from just starting in visual block programming, to Python and C languages.
-
Product
High-performance Computing (HPC) And Cloud
-
In the data center and in the cloud, Altair’s industry-leading HPC tools let you orchestrate, visualize, optimize, and analyze your most demanding workloads, easily migrating to the cloud and eliminating I/O bottlenecks. Top500 systems and small to mid-sized computing environments alike rely on Altair to keep infrastructure running smoothly. With longstanding hardware and cloud provider partnerships, we handle the integrations for you so your team can focus on moving business forward.
-
Product
15.6" Ubiquitous Touch Computer
UTC-515JT
-
15.6" Ubiquitous Touch Computer (IP66&69K) with Intel® Celeron® J6412. 15.6" monitor with 16:9 widescreen display. IP66/69K for full system. Stainless chassis and Anti-corrosion enclosure. M12 for all I/O ports 11~32V wide range system input rating.
-
Product
Embedded Single Board Computers
-
Advantech Embedded Single Board Computer (SBC) series include: 2.5" Pico-ITX, 3.5" PC/104, 5.25" EBX, and MI/O Extension form factors. They offer scalable x86 performance from low power to high-end, and from fanless and slim, to extended temperature platforms with longevity. They are ideal for system integration with high flexibility and expansion possibilities, and compact sizes with rich I/O. Reliability was built in for highly reliable 24/7 operation and industrial grade rugged operation.
-
Product
15.6" All-In-One Touch Computer
UTC-115I
-
15.6" All-in-One Touch Computer with 11th Gen Intel® Core™ i5/i3 Processor. Slimmer and Lighter design. Low power and fanless system design. Built-in Intel® Core™ i5-1145G7E. 15.6" monitor with 16:9 widescreen display.
-
Product
10.1" Touch Computer
UTC-510J
-
10.1" Touch Computer with Intel® Celeron® J6412. Low power & fanless design. Built-in Intel® Celeron® J6412 processor. Provide natural viewing experience with 16:10 10.1" display. Landscape & portrait screen mode support by different applications.
-
Product
21.5" Ubiquitous Touch Computer
UTC-320SL
-
21.5" Ubiquitous Touch Computer with Intel® Core™ 12th–14th Gen Processor. Fan SKU and Fanless SKU system design. Socket Type CPU with Intel® Core™ 12th/13th/14th Gen processor. Multiple power input options (Power Din 4 pins/Terminal Block).
-
Product
6U VPX Single Board Computer
VPX6-195
-
Curtiss-Wright Defense Solutions
Our VPX6-195 6U OpenVPX T2080 Single Board Computer (SBC) combines performance with the advanced I/O capabilities of the NXP's quad-core AltiVec enabled T2080 processor. Designed for SWaP-constrained applications, the VPX6-195 provides two independent processor cores on a single printed wiring board (PWB) with a wide range of standard I/O and each with a XMC mezzanine site to provide twice the processing power.
-
Product
All-In-One Touch Computers & Kiosks Rugged UTC-500 Series
-
The Rugged UTC-500 series all-in-one computers are IP66/69K rated and feature a corrosion-resistant, stainless steel enclosure with waterproof I/O.
-
Product
6U VPX Computing Payload
VP62108
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP62108 is a 6U VPX computing payload based on Intel® 4th generation Core™ Processor. It supports Intel® 4th generation Haswell architecture i3/i5/i7 dual-core or quad-core embedded processor, up to quad-core i7 processor 4860EQ with a life cycle of more than 7 years.VP62108 provides four serial RapidIO (SRIO) x4 links for VPX data plane communications, two x8 PCIe links for VPX expansion plane communications and four Gigabit Ethernet links for VPX control plane communications. Its rich data exchange capability allows users to easily build the whole machine or system-level solutions.VP62108 supports up to DDR3L 16GB ECC memory and offers reliable data transmission. Its onboard solid state Flash managed by a SATA interface controller can be up to 64GB SLC or 128GB MLC. And the entire board uses the reinforced conduction-cooled design and has a wide operating temperature, allowing the user not to worry about its working stability in harsh environments. This feature makes VP62108 particularly suitable for critical mission areas.
-
Product
18.5" Ubiquitous Touch Computer
UTC-318H
-
18.5" Ubiquitous Touch Computer with 8th Gen Intel® Core™ i7/i5/i3 Processor. Low power and fanless system design. Built in Intel® Core™ i5-8365UE. 18.5" monitor with 16:9 widescreen display. Front panel IP65 compliant.
-
Product
High-Performance Computers
EnsembleSeries™
-
Our high-performance compute blades are characterized by their compute power and density achieved by embedding the most contemporary processors, including Scalable Intel® Xeon® datacenter processors.
-
Product
Single Board Computers
-
Advantech RISC-based Single Board Computers (SBC) powered by Freescale and TI ARM, provides multi-integrated functions for easy implementation. Advantech offers a range of RISC solutions including RISC Modules, Single Board Computers (SBC) and Box Computers based on ARM cortex processor technologies. Together with RISC Design Support Services they streamline the whole design process and help customers rapidly develop their own innovations.
-
Product
ProSys-5102, Industrial Embedded Computing Platform
063-502
-
ProSys-5102 is a compact application ready platform with a powerful CPU for various industrial uses, as process control, security, digital signage, IoT edge points and more. The large amount of I/Os enables connectivity for most applications.
-
Product
21.5" Ubiquitous Touch Computer
UTC-520K
-
21.5" Ubiquitous Touch Computer with Intel® N97/Core™ i3-N305 Processor. Low-power, fanless system design. Built-in Intel® N97/Core™ i3-N305. 21.5" monitor with 16:9 widescreen display. IP65-rated front panel for water and dust resistance.
-
Product
All-In-One Touch Computers & Kiosks UTM-700 Series
-
The UTM-700 series is a smart monitor solution featuring 43", 55", and 65" slim-bezel displays.
-
Product
Computer Interface, GPIB and RS-232
SR245
-
Stanford Research Systems, Inc.
The SR245 Computer Interface module is a powerful tool for data acquisition. It provides both an analog and a digital interface between your computer and your experiment.
-
Product
21.5" Ubiquitous Touch Computer
UTC-320K
-
21.5" Ubiquitous Touch Computer with Intel® Atom N97/ Core™ i3-N305 processors. Low power and fanless system design. Built-in Intel® Atom N97/ Core™ i3-N305 processors. 21.5" monitor with 16:9 widescreen display. Front panel IP65 compliant.
-
Product
7" All-In-One Touch Computer
UTC-307J
-
7" All-in-One Touch Computer with Intel® Celeron® J6412 processors. Low power and fanless system design. Built-in Intel® Celeron® J6412 (UTC-307J). 7" monitor with 16:9 widescreen display. Front panel IP65 compliant.
-
Product
Airborne Computers
-
True open systems architecture leverages commercial, off-the-shelf technology, in a high-performance, scalable, and maintainable solution for future applications and next generation computing capabilities. Our mission processor's open architecture is suited for multiple platforms, providing advanced general and display processing for current and future needs.
-
Product
Industrial Computed Tomography
TomoScope® XL
-
Micro focus X-ray source up to 225 kV (option: 300 kV micro focus tube) Grater range of x-ray detectors Grater range of x-ray detectors
-
Product
SMARC Short Size Module with NXP i.MX 8M Plus
LEC-IMX8MP
-
ADLINK LEC-IMX8MP, based on the powerful NXP i.MX8M Plus (quad core Arm Cortex-A53) processor with an optional Neural Processing Unit (NPU) operating at up to 2.3 TOPS., is the first SMARC revision 2.1 compliant module focusing on machine learning and vision, advanced multimedia, and industrial IoT with high reliability. Additionally, it supports dual Image Signal Processors and two camera inputs for an effective Vision System. The LEC-IMX8MP is suited for applications such as smart home, building, city and industry 4.0.
-
Product
Verifier Computer Interface Report
VCIR
-
The Verifier Computer Interface Report (VCIR) is a Windows software package that allows for transferring inspection report from your Inspector series bar code verifier to a computer. Once transferred you can review the ISO/ANSI inspection results or view the scan reflectance profile for detailed troubleshooting. The inspection results can be saved by job for later retrieval or to append new inspection results to the existing job. As each job is saved an Excel spreadsheet (CSV file) is generated. You can customize which parameters should be saved in the spreadsheet. The spreadsheet provides a simple report that will have a line for each bar code inspected.
-
Product
Industrial Computed Tomography
TomoScope® XS
-
Coordinate measuring machine for three-dimensional measurement utilizing computed tomographyFast measurement with high resolution via the next generation transmission tubeReduce measurement time by 90% with OnTheFly TechnologyLow operating costs as a result of the new monoblock designExtremely precise air bearing rotary axis for low measurement uncertaintyLow space requirement thanks to compact designLow weight allows for installation almost anywhereFast amortization through low acquisition costsStandard-compliant calibration for reliable and traceable measurement results, optionally with DAkkS certificateVersatile fields of application such as plastic, metal and multi-material componentsSoftware for 3D real-time reconstruction of workpiece geometries during tomography
