-
product
Flexible Cable Set, 2.4 Mm To 3.5 Mm
85134F
The Keysight 85134F is a 62.9 cm (24.75 in) long1 flexible cable set composed of a 2.4 mm female2 to PSC-3.5 mm female connector and a 2.4 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.31 * sqrt (f) + 0.2, where f is frequency in GHz, for the test port connector and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability1 of the Keysight 85134F is less than 0.12 dB and phase is 0.13*f+ 0.5°, where f is frequency in GHz.
-
product
Universal Test Set
UTS
The Universal Test Set (UTS) is a portable, battery-powered, programmable, ruggedized radio frequency test set designed to validate improvised explosive device (IED) jamming equipment. Our unit is intended to provide an in-field confidence testing for warfighters employing IED jammers prior to departure.
-
product
Universal Three-phase Protective Relay Test Set
Mentor-12
The Mentor 12 is the most advanced three-phase relay test set available for type and field testing of electromechanical and digital protections of any kind, in traditional or IEC-61850 based substations.
-
product
Vacuum Interrupter Test Set
HTZK-IV / 385
Wuhan Huatian Electric Power Automation Co., Ltd.
Quantitative measurement, suitable for vacuum switch vacuum measurement, vacuum switch preventive detection special instrument.
-
product
RF Near Field Probe Set DC to 9GHz
EMF & RF close field sniffer-set for use with any Spectrum Analyzer or Measurement Receiver. The EMC Near Field probe set allows for straightforward pinpointing and measurement of interference sources in electronic component groups as well as execution and monitoring of generic EMC measurement. Our RF near field probe set is especially suitable for: - Pinpointing interference sources - Estimation of interference field strength - Verification of shielding and filtering measures - Identifying faulty components - Detecting circuitry overly sensitive to interference.
-
product
Protection Test Set
CMC 850
The CMC 850 is a protection test set dedicated to IEC 61850. It focuses on the real-time communication methods GOOSE and Sampled Values to interface with the devices under test.
-
product
Single Phase Secondary Injection Test Set
T200A
T200A Single Phase Relay Testing Kit is the best universal secondary injection test set for engineers who need to do all single phase relay test and other basic primary testing which may require single phase long-term high current injection.
-
product
High Pressure/Low Set Point Pressure Switch
J205G
The J205G High Pressure Low Set Point Pressure Switches are among our most versatile offering, affording the end user an extensive operating environment and a wide range of set point optionality.
-
product
Programming
You are looking for a LabVIEW-solution for a test problem? LabVIEW is an excellent development environment for all areas of metrology. Here we have extensive experience and can help in your test problems. In the LabVIEW programming language, we develop VIs (Virtual Instruments) that can be integrated easily in TestStand. Using hardware-oriented programming languages such as C# and LabVIEW, we develop integrations of control and measurement components.
-
product
Power Supply for Hipot Set
Wuhan Fanke Transformer Manufacture Co., LTD
Variable Frequency Power Supply for Hipot Set
-
product
Communications Manufacturing Test Set
CMW100
The R&S®CMW100 communications manufacturing test set is based on the R&S®CMW platform. The flexible RF interface permits simultaneous testing of up to eight devices. The R&S®CMW100 remote control and measurement concepts are compatible with the R&S®CMW500. The R&S®CMW100 is optimized for cost-effective calibration and verification of wireless devices in non-signaling mode (analyzer/generator). The tester provides a new eco-friendly hardware concept, featuring extremely low energy consumption and a very compact size, making it ideal for use in fully automated robotic production lines. It supports LTE, 5G NR, WLAN, Bluetooth® and IoT technologies, making it ready for today and tomorrow.
-
product
Slot 0 Module Retainer Block Set, For Discrete Wiring, 1 Position
510109150
These module retainer blocks are used to attach modules directly to the inner frame of a VXI receiver for discrete wiring. These modules then hinge down with the receiver to provide easy access to wiring.
-
product
Quantitative Analysis Program
AutoQuant Pro
AutoQuant Pro is a powerful new automated, multi-component, quantitative analysis program for analyzing gas phase mixtures in real time. The program provides a comfortable user interface for operating a MIDAC FTIR analyzer, defining analytical methods for computing concentrations of compounds, displaying and outputting results, and automating data collection for multiple sample stream installations.
-
product
TD Series High Voltage DC Test Set
TD2000A
TD series testing equipment is a High Voltage DC Test Set consisting of control unit and DC high current output unit. And the TD series HVDC primary injection system includes 3 types, which could output 2000Adc/4000Adc/ 8000Adc and 0.1% high accuracy, suitable to be used for different HVDC testing requirements, such as in HVDC Converting station, or railway transportation line, etc.
-
product
Optical Talk Sets
JW4103N
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW4103N Optical Talk Set is an intelligent and efficient instrument that combines in one set the functions of both a digital optical phone and a stabilized light source. It is widely used in operations of installation, optical testing, maintenance and fiber attenuation value testing in data network, CATV and Telecommunication network.
-
product
TRUEngine program
TRUEngine
A TRUEngine is an engine which has been maintained to GE or CFM manuals and recommendations. A TRUEngine contains TRUEngine LLP, which are life-limited parts (LLP) that have always operated in GE- or CFM- approved configurations. When rotating LLP and their associated critical influencing parts and all other internal engine parts are confirmed for GE- or CFM-approved configuration, the engine is eligible for TRUEngine status.
-
product
3" Casters, Set Of 4
HW-63
3" diameter casters for all vertical cabinets offer mobility where needed. Meets or exceeds ANSI and GSA specifications. Shipped uninstalled unless specified.
-
product
Engine Speed Control and Measurement (Test Set A)
MS 1100
*Checks the parameters such as current, voltage, speed, and turbine gas temperature of 804E and 811 engines Portable instrument*Testing of Automatic engine control system and after burner control system*Simulates the temperature signal derived from the engine TGT (Temperature Gas Turbine) thermocouples*Simulates the speed signal, NL (low pressure shaft speed signal) drive from the L.P shaft Probe*Indicates the current signal to the FCU solenoid derived from the engine control amplifier*Measure the TGT and NL simulated signal at static position*Measure the signal produced by the engine TGT thermocouples*Measure the NL signal produced by the LP shaft*Measure the NH (High-pressure shaft speed) signal produced by HP shaft*Indicates the solenoid current, produced by the engine control amplifier*Indicates the solenoid voltage, produced by the engine control amplifier*Used to test engine in both static and dynamic states
-
product
Test Program Quality Verification
CodeReport
CodeReport is an easy-to-use application for verifying test program quality. CodeReport comes with many different, known quality screening rules that can be used to verify your test program is complete and ready for production. CodeReport also provides a graphical Rule Editor that allows you to create your own, custom rules. Ensure your coding standards and quality specifications are correct by generating your set of rules, checks, and screenings. Easily generate a detailed report for locating, correcting, and documenting the state of your test program. Quickly identify the tester hardware and instrumentation needed to run your program with the Tester Resource report. Save a session file to quickly return to your project after edits have been made or use the Session on other similar projects to transfer your configuration and custom rules.
-
product
RAMP TEST SET
AN/USM-719
Tel-Instrument Electronics Corp.
Based on entirely new up-to-date technology and digital architecture; the AN/USM-719 large 4.75" x 3.5" in. color LCD screen and surrounding soft-keys and keyboard provides easy and quick access to a multiple of test screens menus, and display options affording single man operation, instant results, and a host of pre-programmed and manually variable parameters to meet the most demanding requirement's for testing of advabced airborne avionic and transponder/interrogator systems.
-
product
Relay Buddy Adapter Set
190-4
*Expands the testing capability of your Relay Buddy! *3 pack of adapters allows testing of shielded relays, same relays tested by #190 Relay Buddy *Relay adapter plugs into Relay Buddy first *Shielded relay then plugs into the top of the adapter
-
product
6 PCS Deluxe Light Set
3606
Peaceful Thriving Enterprise Co Ltd
Kit packed in a deluxe blow mold case.Quick, efficient and economic way to find faults find on the following electronic fuel (EFI) system:1. 3405-BOSCH PFI2. 3410-GM TBI3. 3411-FORD TBI4. 3412-GM PFI5. 3413-GEO TBI6. 3414-GM SCPI.
-
product
Automated Fibre Loss Test Set
LTS-1500
The LTS-1500 is a small, rugged automated fiber optic loss test set that characterises singlemode fiber links at wavelengths of 1310, 1490 and 1550 nm. It is comprised of a sensitive InGaAs based optical power meter calibrated at six wavelengths with better than -75 dBm noise level plus a stabilised laser light source with up to three selectable wavelengths.
-
product
Test Sets For Transformer Industries
Contemporary Test Sets For Transformer Industries are developed to recognize the potentially disastrous current transformer errors. They prevent the primary current from overpowering insulation and short circuits. They are used for developing a testing and maintenance plan for addressing the errors before any failure to save money and time. With these powerful test sets, they are sure to perform saturation testing to test the knee point of a signal by comparing primary and secondary windings.
-
product
The Imperas Instruction Set Simulator
ISS
The Imperas ISS is often the first simulation product used in an embedded software development project. The Imperas ISS allows the development and debug of code for the target architecture on an x86 host PC with the minimum of setup and effort. It simply requires the cross compilation of your application and running the ISS with an argument to specify the name of the application object.
-
product
Multifunction Substation Test Set
STS 5000
STS 5000 is a multifunction substation maintenance & commissioning test system for current, voltage and power transformers designed to perform primary tests requested in substations commissioning. It allows to perform accurate tests on CTs, VTs, PTs and ground grid.
-
product
Universal Primary Injection Test Set for Substation Assets
CPC 100
The patented CPC 100 primary injection test system replaces several individual testing devices. This reduces the costs for training and transport, and cuts down testing time.
-
product
Flexible Cable Set, 3.5 Mm (Test Port) To 7 Mm
85132F
The Keysight 85132F is a 62.9 cm (24.75 in) long¹ flexible cable set composed of two 3.5 mm female² to 7 mm connectors. Cable frequency range is dc to 18 GHz with a return loss greater than or equal to 17 dB. Insertion loss is 0.25 * sqrt(f) + 0.2, where f is frequency in GHz, for the test port connector and device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability¹ of the Keysight 85132F is less than 0.12 dB and phase is 0.13 * f + 0.5, where f is frequency in GHz.
-
product
High Voltage Test Sets
Nmc's high voltage test sets are manufactured as per the customers requirement ranging from 5kv-100kv ac or dc.
-
product
Ionization Test Set
PFK-105
- Ionization Test Kit for Measuring Offset Voltage and Discharge Times- Includes a Field Meter, Charge Plate Monitor, ±1000 Volt Charger and Decay Timer- Balance Ionizers per ANSI/ESD SP3.3 Periodic Verification- Measure Ionizer Decay time as per ANSI/ESD S3.1 and ANSI/ESD SP3.3.- Measure Body Voltage Generation and Decay- Evaluate Ionizers and Packaging Materials- Includes a fixture to hold the PFM-711B, CPM-720B and PDT-740B as one- Molded Carrying Case with Foam Insert Included
