-
product
PXIe-4497, 204.8 kS/s, 114 dB, 2 Gains, AC/DC-Coupled, 16-Analog Input PXI Sound and Vibration Module
781369-01
204.8 kS/s, 114 dB, 2 Gains, AC/DC-Coupled, 16-Analog Input PXI Sound and Vibration Module - The PXIe‑4497 is designed for high‑channel‑count sound and vibration applications. With 24-bit analog inputs and IEPE constant current signal conditioning, the PXIe‑4497 is ideal for making precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. The PXIe‑4497 delivers simultaneous sample on all channels. In addition, the module includes built-in antialiasing filters that automatically adjust to your sample rate, software-selectable input gain, and TEDS smart sensor support for error-free setup. Common applications include noise, vibration, and harshness (NVH) analysis; large microphone arrays; and dynamic structural test.
-
product
PXI 32 Channel Switch Simulation Module
40-480-221
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
product
Razor Express 16XX CompuScope 16-Bit, 200 MS/s, PCIe Digitizer / Oscilloscope
The GaGe Razor Express16XX CompuScope PCIe digitizer board features 16-bit resolution with sampling rates up to 200 MS/s with true Effective Number of Bits (ENOB) of 11.7-bits with 10 MHz input.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 20 MS/s on 2 Channels (Single Ended) or 2 Channels (Differential)
M2P.5921-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 2.5 GS/s on 2 Channels, 1.5 GHz Bandwidth
DN2.222-02
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
product
10 GSPS, 14-Bit Digitizer
ADQ7DC
With 14 bits and 10 GSPS, ADQ7DC improves the resolution in high-sampling rate applications beyond what was previously possible. This performance-boost has effectively helped our customers overcome performance trade-offs and have led to significant advances in many applications. ADQ7DC can be operated in either single- or dual-channel mode with 10 or 5 GSPS sampling rate respectively.
-
product
NI-9375 , 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781030-01
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
product
NI-5762, 250 MS/s, 16-Bit, 100 MHz Bandwidth, 2-Channel Digitizer Adapter Module for FlexRIO
781749-01
The NI‑5762 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that simultaneously samples two channels at 250 MS/s with options for 100 MHz of analog bandwidth or an unfiltered path. You can use the NI‑5762 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
product
Digital IO
PA32IX
The PA32IX represents a new level of performance and capabilities for PXI-based digital instrumentation. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 512 bi-directional pins (16 boards). The PA32IX also supports deep pattern memory by offering 64 M of on-board vector memory with static per pin direction control and with test rates up to 50 MHz.
-
product
12-Bit, 2.5 GSPS Digitizer Optimized for Pulse Detection
ADQ32-PDRX
ADQ32-PDRX acquires the input signal via a single connector and uses an onboard splitter to separate the signal into two paths with different gain settings. The high gain path is used to accurately capture low-amplitude portions of the input signal whereas the low gain path ensures the acquisition of high-amplitude peaks without causing saturation. The two signal paths are then combined in real-time inside the onboard field-programmable gate array (FPGA) to create a digitized output with improved performance.PDRX increases the dynamic range by 3 bits and is fully integrated into the digitizer for fast and easy system-level integration. ADQ32-PDRX is therefore comparable with a 16-bit digitizer in terms of dynamic range, but with the benefit of offering a higher sampling rate.
-
product
FPGA PXI High-Performance Digital I/O Card
GX3702
The GX3702 is a user configurable, FPGA-based, 3U PXI card which offers 160 digital I/O signals which can be configured for single-ended or differential interfaces. The card employs the Altera Stratix III FPGA, which can support SerDes data rates up to 1.2 Gb/s, digital I/O clock rates of 700 MHz, and features over 45,000 logic elements and 1.836 Kb of memory. The GX3702 is supplied with an integral expansion board providing access to the FPGA's 160 I/Os and is pin for pin compatible with the NI PXI 7813R and 7811R FPGA cards . Alternatively, users can design their own custom expansion cards for specific applications - eliminating the need for additional external boards which are cumbersome and physically difficult to integrate into a test system. The design of the FPGA is done by using Altera's free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded into the FPGA directly or via an on-board EEPROM.
-
product
PXI Digital I/O Module
PXI Digital I/O Modules offer up to 96 channels of digital I/O, with compatibility for a variety of voltage and isolation levels. Some models include programmable input filters to eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter. PXI Digital I/O Modules are ideal for a range of applications, from manufacturing test and industrial control to advanced aerospace and laboratory research.
-
product
FPGA PXI High-Performance Digital I/O Card
GX3700
The GX3700 is a user configurable, FPGA-based, 3U PXI card which offers 160 digital I/O signals which can be configured for single-ended or differential interfaces. The card employs the Altera Stratix III FPGA, which can support SerDes data rates up to 1.2 Gb/s, digital I/O clock rates of 700 MHz, and features 47,500 logic elements and 2.1 kb of memory. The GX3700 is supplied with an integral expansion board providing access to the FPGA’s 160 I/Os. Alternatively, users can design their own custom expansion cards for specific applications - eliminating the need for additional external boards which are cumbersome and physically difficult to integrate into a test system. The design of the FPGA is done by using Altera’s free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded into the FPGA directly or via an on-board EEPROM.
-
product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 500 MS/s Digitizer on 4 Channels, 625 GS/s AWG on 4 Channels
DN2.825-04
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
NI-9425 , 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
780176-01
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
product
PCI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, Digital I/O Device
778833-01
The PCI-6528 is an industrial, parallel digital I/O interface.With programmable power-up states, you can configure the initial output states in software, to ensure safe … operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
Electrical High Speed Digitizer
M8296A
The Keysight M8296A is a four-channel, high-speed electrical digitizer module for the AXIe platform. It can synchronously sample up to four incident waveforms and is ideally suited to digitize the output signals from a dual-polarization coherent receiver. Keysight's vector signal analyzer and optical modulation analyzer software serves as the M8296A's user interface and enables a multitude of test and measurement tasks such as spectral analysis and digital demodulation for the analysis of signal quality metrics like error-vector magnitude. Furthermore, the sampled waveform can be stored and processed with the user's own tools (e.g. using Matlab). The modular approach allows users to combine the M8296A high-speed digitizer with other modules in one mainframe such as the M8292A modular optical modulation analyzer and the M8196A 92 GSa/s arbitrary waveform generator.
-
product
PCIe-6537B, 32-Channel, 50 MHz, 200 MB/s Digital I/O Device
782631-01
32-Channel, 50 MHz, 200 MB/s Digital I/O Device - The PCIe-6537 can continuously stream data over the PCI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 250 MS/s on 4 Channels, 4 Single-Ended Inputs
DN2.442-04
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
NI-9403, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780179-01
5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The NI‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9403 for applications such as custom, high-speed counter/timers; digital communication protocols; and pulse generation. In a CompactDAQ chassis, you can use the NI‑9403 only as a static (software-timed) digital I/O module. You cannot use these modules to route timing or triggering signals.
-
product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
782401-01
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 500 MS/s on 20 Channels, 20 Single-Ended Inputs
DN6.445-20
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5280 Series
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 40 MS/s on 4 Channels, 4 Single-Ended Inputs
DN2.593-04
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
product
C Series Digital Module
The C Series Digital Module interacts with a range of industrial switches, transducers, and devices. Some modules include an LED per channel that indicates the state of the channel. It supports input, output, or a combination of digital lines, and they can interact with a variety of voltages and logic levels, so they are well-suited for a variety of benchtop and industrial environments. Additionally, the C Series Digital Module also offers isolation options and sinking or sourcing capabilities to add further protection to your digital I/O application. When you use the C Series Digital Module with CompactRIO, you can use LabVIEW FPGA to create custom high-speed counter/timers, digital communication protocols, pulse generation, and more.The C Series Digital Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
PCIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PCI FlexRIO Digitizer Device
785648-01
The PCIe-5774 is a PCI FlexRIO Digitizer Device that provides up to 3.2 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset. The PCIe-5774 is ideal for time-domain measurements in areas such as scientific instrumentation, medical imaging, and particle physics. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
product
64-CH Isolated Digital I/O PCI Cards
PCI-7432/7433/7434
ADLINK's cPCI/PCI-743X series cards are 64-CH high-density digital input and/or output cards that provide a robust 2,500 V isolation protection and are suitable for most industrial applications. The wide input range of the cPCI/PCI-7432 and cPCI/PCI-7433 makes it easy to sense the status of external devices. There are several options for PCI-743X series, such as normal version with input range from 0 to 24 V, as well as HIR version with high input range from 0 to 50 V. The PCI- 7433ALC is specifically designed for AC power test system.
-
product
NI-9222 , ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781397-01
±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
product
Multi-Channel 10-Bit Digitizer
ADQ8-8C
With compact modular form factors, 8 channels per board, and high-precision multi-board synchronization capabilities, ADQ8-8C is ideal for massive multi-channel implementations.
-
product
PCIe Octopus Express 16-Bit Digitizer
The GaGe Octopus Express 84XX CompuScope PCIe digitizer board features 16-bit resolution with sampling rates up to 25 MS/s with true Effective Number of Bits (ENOB) of 12-bits with 10 MHz input.
