-
Product
AC Power Line EMI Filters
CleanSweep®
-
CleanSweep® filters block EMI on power lines (both common and differential modes) and, uniquely, in ground, from reaching sensitive equipment. They also reduce EMI "backflow" from a "noisy" source that otherwise would end up on your AC power network.
-
Product
Vacuum, Module, Receiver, 90 Series, 2 Port Positions w/ Filter
510104266
-
Primary mating module 510108242. (May mate with other ITA modules, as well.)
-
Product
ABex Passive Terminal Module
ABex TM-6363 MDAQ
-
The ABex TM-6363 is an ABex terminal module for the ABex system to route signals from a NI-PXIe-6363 device directly to the front connector of the ABex. It is only a feedthrough-module.
-
Product
250 MHz Passive Probe for HDO4000, 10:1, 10 MOhm
PP017-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
Product
"Standard" RF Low Pass Filters
-
Coaxial Dynamics "Standard" line of RF Low Pass Filters offers several models to choose from at CW power ratings of 100 watts and 200 watts. These filters cover operating frequencies from 88 MHz to 400 MHz with less than 0.5 dB insertion loss and attenuation levels of 40, 50 and 60 dB.
-
Product
Passive probe with X1/X10 switch
-
They are normally designated X1 and X10, although 1X and 10X are sometimes seen. The designation refers to the factor by which the impedance of the scope itelf is multiplied by the probe.The X1 probes are suitable for many low frequency applications. They offer the same input impedance of the oscilloscope which is normally 1 MΩ. However for applications where better accuracy is needed and as frequencies start to rise, other test probes are needed.
-
Product
GPS, GLONASS, Galileo Splitter 8 Way, SMA, 1000 - 2000 MHz, 50 Ohm, Passive
GPS810
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo SplitterLow Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA Max on DC Block PortsRoHS Compliant Splitter Construction
-
Product
Low-PIM, High-Power Filter Solutions for Monitoring Broadband Emissions
-
Enables monitoring of PIM to 13 GHz; 100W CW and 1KW peakNear-end monitoring: Carriers rejected -90dB by the notchtravel through the bandpass filter to the low PIM termination.Far-end monitoring: Carriers rejected -90dB by the highpass,IM products passed are monitored by the spectrum analyzer.
-
Product
DC Filter Inductors
-
Osborne DC filter inductors (aka filter chokes) are commonly used in AC to DC conversion circuits to present an inductive voltage drop to the AC component of rectified current. This inductive voltage drop acts as a filter. Osborne designs filter inductors to components to function effectively (without saturation) in the presence of the DC current. Osborne will work with you to mitigate the impact of ripple frequency in conversion circuits. Every Osborne DC filter choke is designed for high performance with special consideration given to your circuit´s power supply frequency and conversion configuration.
-
Product
Passive XMC-to-PCI Express Adapter
5944
-
The Technobox, Inc. P/N 5944 is designed to adapt a single-wide XMC card to a 16X PCI Express slot. The 5944 supports both P15 and P16 and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
Product
Tunable Optical Filters
-
DiCon's MEMS tunable optical filter offers many advantages over a traditional tunable optical filter; increased accuracy & resolution, a faster tuning speed, as well as a durability that will last for over a billion tuning cycles, all in a compact package. Options are available for either 100 GHz or 50 GHz channel spacing as well as operation in either the O-band, C-band or L-band wavelength ranges.
-
Product
Passive Imaging & Radiometers
PMMW
-
A low attenuation atmospheric window from 80-110 GHz (W Band) makes this band an ideal candidate for PMMW systems. Passive imagers operate by detecting naturally emitted thermal (black body) radiation from an object. Products available up to 345 GHz.
-
Product
GPS, GLONASS, Galileo Splitter 2 Way, SMA, 1000 - 2000 MHz, 50 Ohm, Passive
GPS210
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portTri Alloy SMA Female (Jack) 50 Ohm
-
Product
Switched Filter Banks
-
K&L Microwave provides Switched Filter Bank (SFB) products built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications. Use the quote cart to request a quote on an existing design or to provide specifications for a custom design.
-
Product
Attenuation 1000 High Voltage Passive Probe
-
* high voltage multimeter probe is a 1000:1 fixed attenuation ratio passive probe. This probe is designed to test high voltages for multimeters. With high voltage and high precision.* The test signal can be read on the multimeter, and the multimeter multiplied by 1000 is the actual test result.* High reliability and high security.* The highest voltage can measure DC up to 30KV.
-
Product
Optical Filters
-
Alnair Laboratories Corporation
The filter exhibits an ultra-sharp roll-off of 1500dB/nm(12dB/GHz), without compromising the flexibility ofbandwidth- and wavelength-tuning. Ideal for DWDMchannel selection and removing ASE noise.
-
Product
Blocklist Based Filtering
-
Many businesses prefer to use blocklists prepared by external intelligence agencies to save the time of generating this data themselves. Also, to get as much exposure and intelligence of the threat landscape as possible. However, this blocklist information can be sent in various formats, making utilizing them a challenge. Luckily, FastNetMon is a flexible blacklisting feed filtering tool that supports a vast array of formats to receive, consume, and use blocklists from different intelligence feed providers. FastNetMon then enables you to block specific malicious and dangerous hosts using blocklist-based filtering.
-
Product
Rack Module with Standard Contactors without Anti-Harmonic filters
MOD Rack
-
Lifasa - International Capacitors, SA
The MOD-RACK control units include, in a compact form, all the components necessary for the operation of a step of a standard capacitor bank. MOD-RACK modules are divided into two basic blocks: power block and control block. The two blocks are mounted in a small frame to be installed in an electrical panel.
-
Product
GPS Antenna Signal Splitter 3 Way, N Type, Passive, L1 & L2, 50 Ohm
GPS300
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo SplitterLow Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsRoHS Compliant Splitter Construction
-
Product
Gas Filter Correlation CO Analyzer
Model T300U
-
Teledyne Advanced Pollution Instrumentation
The Model T300U Trace-level CO analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. Using IR absorption with a Gas Filter Correlation Wheel, the T300U is designed to allow ultra-sensitive CO measurements while still meeting the requirements for use as a US EPA compliance analyzer.The optical bench is enclosed in a temperature controlled oven, dramatically decreasing instrument noise and drift. The objective and field mirrors in the sample cell are gold plated to maximize signal to noise performance, while a temperature-controlled Nafion dryer on the inlet minimizes water interference caused by ambient humidity changes. Periodically, the T300U seamlessly corrects its baseline by routing the sample through a heated catalytic CO scrubber. This Auto Reference function corrects zero drift and reduces the effect of interferences.
-
Product
Bandpass Filters
-
K&L Microwave provides bandpass filters in multiple topologies built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications, as well as product families. Use the quote cart to request a quote on a specific design.
-
Product
Digital Noise Filter
DSP-599zx
-
The DSP-599zx, with highly aclaimed digital noise filters, is part of the latest generation Timewave DSP filters. Incorporating the newest high speed CPU, the extra power gives the user unparalleled features and field upgradeability for the future. The new LCD display, pushbuttons, and Visible Memory let you see the exact settings of the filter. The optical encoders give the operator continuous tuning of the filters.
-
Product
Real Time Digital Filters
-
Real Time Digital Filters can be used to filter a measured signal in real time. Filter characteristics can be defined by the user to meet the requirements of a specific application. Real-time digital filters are applied in the data conditioning phase. The filters are designed with a graphic design tool and then uploaded to the front-end for real-time calculation. The graphic design tool defines the filter performance vertical axis with a dB scale. The horizontal axis is defined as relative frequency.
-
Product
5-slot ATX-supported 2U Butterfly PICMG 1.3 Bus Passive Backplane
FAB205
-
The FAB205 features a PICMG 1.3 CPU card slot, five 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. The FAB205 is optimized to support AXIOMTEK's PICMG 1.3 system host boards, the SHB100 and SHB110, which are built around the PICMG 1.3 form factor. The FAB205 is compatible with the AX61220/AX61222 chassis.
-
Product
Passive Waveguide Components
-
We cover all kinds of connections between waveguide, coaxial, micro-strip and co-planar lines. Filters are available in waveguide technology as well as in stripline/micro-strip. Passive structures such as power splitter, power combiner, ortho-mode transducer and hybrids mostly are designed to meet the specific goals of the customer.
-
Product
T3DSO Passive Probe, 350 MHz, 1X/10X, 1 MOhm/10 MOhm, 300V/600V
T3PP350
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
Product
Narrow Band Filters (Single Octave)
POWER-POLE® Series
-
The POWER-POLE® Series of tunable filters provides improved RF performance with increased power handling capability and the lowest insertion loss for a given bandwidth. The product line includes several standard designs in various frequencies to support almost any application. Approximate performance is summarized in the POWER-POLE Series Selection Guide.
-
Product
Narrow Band Filters (Single Octave)
MAXI-POLE® Series
-
The MAXI-POLE® Series of tunable filters provides improved passband performance (reduced insertion loss for a given bandwidth) in a slightly larger package. The product line includes several standard designs in various frequencies to support almost any application. Approximate performance is summarized in the Maxi-Pole Series Selection Guide.
-
Product
4 Way GPS / GNSS Signal Splitter IP67 Outdoor, SMA, 1-2 GHz, 50 Ohm, Passive
GPS411
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo SplitterLow Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy SMA Female (Jack) 50 Ohm
-
Product
Gas Filters
-
WITT gas filters enable the finest filtering of impurities in technical gases such as acetylene, argon., oxygen, hydrogen, methane, carbon dioxide, helium, compressed air and ethylene. They thus protect downstream equipment and systems. Some gas filters are also referred to as gas cleaners.
